Loading ...
Loading ...
Loading ...
10
Enter the default Master Code
(123456)
to
complete the bolt direction setting.
Change the Master Code before operating the lock.
See Change Master Code on page 01.
Press SET BUTTON to exit programming mode.
Turn On.
1
＋
Turn Off.
0
＋
Enter new digits (10 - 99 seconds)
then press
This will erase all stored information, including the current Master Code and existing User Codes.
09
Auto-lock Delay Timer
・Auto-lock timer can be set from 10 to 99 seconds according to your demand.
Press
0
7
Enter current Master Code (4-6 digits)
then press
Press [SET] button once
1
2
3
4
06
Vacation Mode
・Disabled by default.
・
When Vacation Mode is enabled, only the current Master Code (4-6 digits) can unlock the lock.
・The stored User / Single-entry Codes will be re-activated once the Vacation Mode is disabled.
Press
0
5
Enter current Master Code (4-6 digits)
then press
Press [SET] button once
1
2
3
4 4 4
07
Enable or Disable Beeper
・The beeper can be turned off if desired. Beeps will still sound during programming.
Press
0
6
Enter current Master Code (4-6 digits)
then press
Press [SET] button once
1
2
3
08
Auto-lock Function
・Disabled by default.
・When enabled, the lock will automatically re-lock after unlocking (Default: 10 seconds).
Press
0
8
Enter current Master Code (4-6 digits)
then press
Press [SET] button once
1
2
3
Enter New Single-entry Code (4 digits)
Add another code
05
Add Single-entry Code(s)
・The Single-entry User Code can be used for only one successful entry and will be invalid
when the lockset is locked again.
・The unit can store up to 5 Single-entry User Codes (4 digits long).
Press
12
Enter current Master Code (4-6 digits)
then press
Press [SET] button once
1
2
3
4
3
Name
User Code (4-6 digits)
Restore to Factory Settings
11
ACCESS CODE LIST
After changing your Master Code, do not pass your Master Code to
anyone else.
MASTER CODE (4-6 digits)
WRITE YOUR MASTER CODE HERE FOR EASY ACCESS
FEDERAL COMMUNICATIONS COMMISSION STATEMENT
IC REGULATIONS
This Class B digital apparatus complies with Canadian ICES-003.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation of the device.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Turn On.
1
＋
Turn Off.
0
＋
Turn On.
1
＋
Turn Off.
0
＋
1 2
Remove one battery
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
Press and hold SET button while inserting the
battery back. Hold the set button until long
beep over.
Loading ...
Loading ...
Loading ...