BAUMR-AG SAWMCTBM3CVA Metal Cut Off Saw 2400W User Manual

User Manual

[Revision 1.0]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE AND MAY

VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by this manual may vary in appearance,

assembly, inclusions, specifications, description, and packaging.

CS-355 Cold Cut Off Saw

E&OE © Baumr-AG 2

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death, injury or

equipment or property damage if not understood or followed. Safety messages have the following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be INJURED if you do

not follow instructions or equipment

damage may occur.

It is vital that you read and understand this

user manual before using the product,

including safety warnings, and any assembly

and operating instructions. Keep the manual

for future reference.

Safety precautions and recommendations

detailed here must be fully understood and

followed to reduce the risk of injury, fire,

explosion, electrical hazard, and/or property

damage.

Safety information presented here is generic

in nature – some advice may not be

applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery powered or

combustion engine powered.

• Before Use - If you are not familiar with the

safe operation/handling of the equipment or

are in any way unsure of any aspect of

suitability or correct use for your

application, you should complete training

conducted by a person or organization

qualified in safe use and operation of this

equipment, including fuel/electrical handling

and safety.

• Do NOT operate the equipment in

flammable or explosive environments, such

as in the presence of flammable liquids,

gases, or dust. The equipment may create

sparks or heat that may ignite flammable

substances.

• Keep clear of moving parts.

• Equipment may be a potential source of

electric shock or injury if misused.

• Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

• Do NOT allow others to use the equipment

unless they have read this manual and are

adequately trained.

• Keep packaging away from children - risk

of suffocation! Operators must use the

equipment correctly. When using the

equipment, consider conditions and pay

due care to persons and property.

General Work Area Safety

•

Work areas should be clean and well it.

• Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

• If devices are provided for connecting dust

extraction / collection facilities, ensure

these are connected and used properly.

Dust collection can reduce dust-related

hazards.

General Personal Safety

•

Wear appropriate protective equipment

when operating, servicing, or when in the

operating area of the equipment to help

protect from eye and ear injury, poisoning,

burns, cutting and crush injuries. Protective

equipment such as safety goggles,

respirators, non-slip safety footwear, hard

hat, hearing protection etc should be used

for appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective equipment.

Do not wear loose clothing or jewellery,

which can be caught in moving parts. Keep

hair and clothing away from the equipment.

• Stay alert and use common sense when

operating the equipment. Do not over-

reach. Always maintain secure footing and

balance.

• Do not use the equipment if tired or under

the influence of drugs, alcohol, or

medication.

• This equipment is not intended for use by

persons with reduced physical, sensory, or

mental capabilities.

General Fuel Safety

•

Petrol/fuel/gasoline is extremely flammable

– keep clear of naked flames or other

ignition sources.

• Do not spill fuel. If you spill fuel, wipe it off

the equipment immediately – if fuel gets on

your clothing, change clothing.

• Do NOT smoke near fuel or when

refuelling.

• Always shut off the engine before

refuelling.

• Do NOT refuel a hot engine.

• Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly.

• Always refuel in well-ventilated areas.

• Always check for fuel leakage. If fuel

leakage is found, do not start, or run the

engine until all leaks are fixed.

General Carbon-Monoxide Safety

•

Using a combustion engine indoors CAN

KILL IN MINUTES. Engine exhaust

contains carbon-monoxide – a poison you

cannot smell or see.

• Use combustion engines OUTSIDE only,

and far away from windows, doors, and

vents.

General Equipment Use and Care

•

The equipment is designed for domestic

use only.

• Handle the equipment safely and carefully.

• Before use, inspect the equipment for

misalignment or binding of moving parts,

loose components, damage, or any other

condition that may affect its operation. If

damaged, have the equipment repaired by

an authorised service centre or technician

before use.

• Prevent unintentional starting of the

equipment - ensure equipment and power

switches are in the OFF position before

connecting or moving equipment. Do not

carry equipment with hands or fingers

touching any controls. Remove any tools or

other items that are not a part of the

equipment from it before starting or

switching on.

• Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be safer

when used within its design and usage

parameters.

• Use the equipment and accessories etc. in

accordance with these instructions,

considering working conditions and the

work to be performed. Using the equipment

for operations different from those intended

could result in hazardous situations.

• Always keep equipment components

(engines, hoses, handles, controls, frames,

housings, guards etc) and accessories

(cutting tools, nozzles, bits etc) properly

maintained. Keep the equipment clean and,

where applicable, properly lubricated.

• Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the equipment

near flammable materials, combustible

gases, or liquids etc.

• The equipment is not weather-proof, and

should not be stored in direct sunlight, at

high ambient temperatures or locations that

are damp or humid.

• Do not clean equipment with solvents,

flammable liquids, or harsh abrasives.

• For specific equipment safety use and care,

see Equipment Safety.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CS-355 Cold Cut Off Saw

E&OE © Baumr-AG 3

General Electrical Safety

•

Inspect electrical equipment, extension

cords, power bars, and electrical fittings for

damage or wear before each use. Repair or

replace damaged equipment immediately.

• Ensure all power sources conform to

equipment voltage requirements and are

disconnected before connecting or

disconnecting equipment.

• When wiring electrically powered

equipment, follow all electrical and safety

codes.

• Always use a Residual Current Device

(RCD) (GFCI) / Earth Leakage Circuit

Breaker / Safety Switch when operating this

item (electrical items only).

• High voltage / high current power lines may

be present. Use extreme caution to avoid

contact or interference with power lines.

Electrical shock can be fatal.

General Electrical Safety

•

Electrically grounded equipment must have

an approved cord and plug and be

connected to a grounded electrical outlet.

• Do NOT bypass the ON/OFF switch and

operate equipment by connecting and

disconnecting the electrical cord.

• Do NOT use equipment that has exposed

wiring, damaged switches, covers or

guards.

• Do NOT use electrical equipment in wet

conditions or in damp locations.

• Do NOT use electrical cords to lift, move or

carry equipment.

• Do NOT coil or knot electrical cords, and

ensure electrical cords are not trip hazards.

General Service Information

•

The equipment must be serviced or

repaired at authorised service centres by

qualified personnel only.

• Replacement parts must be original

equipment manufacturer (OEM) to ensure

equipment safety is maintained.

• Do NOT attempt any maintenance or repair

work not described in this manual.

• After use, the equipment and components

may still be hot – allow the equipment to

cool and disconnect spark plugs and/or

electrical power sources and/or batteries

from it before adjusting, changing

accessories, or performing repair or

maintenance.

• Do NOT adjust while the equipment is

running.

• Perform service-related activities in suitable

conditions, such as a workshop.

• Replace worn, damaged or missing

warning/safety labels immediately.

Child Choking Hazard!

• W

ARNING: CHOKING HAZARD - CHILDREN UNDER 8 YRS. CAN CHOKE OR SUFFOCATE ON SMALL PARTS. ADULT

SUPERVISION REQUIRED.

• Carefully inspect anything a baby or child could gain access to, including this product & packaging.

• Dangers include anything of a size that could become stuck or lodged in a baby or child's airway.

• Dangers include things like raw, hard fruit and vegetable pieces, large pieces of meat, bones or sausage skins, popcorn, nuts,

hard lollies and corn chips, small magnets and batteries, coins, beads, marbles and small uninflated balloons, broken toys and smaller toys,

buttons, keys, and coins. But there are also many more.

• Pay particular attention to accessories, nuts, bolts, screws, washers, caps, covers, loose parts, parts that could be removed or break off, pieces

of packaging, staples, tape etc.

• In the case of any doubt, secure the item of concern in an appropriate manner, or completely remove the possibility of access by a baby or child.

IMPORTANT WARNINGS ON MOVING BLADES

• BE

AWARE THAT THE EQUIPMENT MAY INCLUDE HAZARDOUS COMPONENTS, SUCH AS BLADES, HOT SURFACES AND MOVING

PARTS.

• MOVING BLADES CAN CAUSE SERIOUS INJURY AND EVEN DEATH IF USED IMPROPERLY OR WITHOUT SUFFICIENT PPE.

• DO NOT USE THIS EQUIPMENT ON UNEVEN SURFACES AND ALWAYS MAINTAIN GOOD BALANCE WHEN USING THIS EQUIPMENT.

FAILURE TO DO SO MAY CAUSE SERIOUS INJURY.

• MAINTAIN A SECURE GRIP OF THE TRIGGER ASSEMBLY AT ALL TIMES.

Safety Regulations for Cold Cut Saws

• W

ARNING! WHEN USING ELECTRIC TOOLS. ALL THE SAFETY INSTRUCTIONS SHOULD ALWAYS BE OBSERVED TO REDUCE THE

RISK OF FIRE, ELECTRIC SHOCK AND PERSONAL INJURY BEFORE ATTEMPTING TO OPERATE THE TOOL, PLEASE READ ALL THE

INSTRUCTIONS AND SAVE IT FOR FURTHER REFERENCE.

• KEEP WORK AREA CLEAN. Cluttered area and benches invite injuries.

• CONSIDER WORK AREA ENVIRONMENT. Don't use electric tools in damp or wet locations. Don't expose electric tools to rain. Keep work area

well-lit, in particular, no inflammable liquids or gases must be present.

• AVOID ELECTRIC SHOCK. When you are operating tool. Don't touch metal being grounded, such as pipe, radiators, freezers, etc.

• KEEP CHILDREN AND VISITORS AWAY. Don't let children contact tool on extension cord. All visitors should be kept away from work place.

• STORE IDLE TOOL. When not in use, tools should be stored dry high, or locked-up place.

• DON'T FORCE TOOL. It will do the job better and safer at the rate.it is intended. Avoid unnecessary over load which may put the operator at risk

and impair function of

the tools.

• USE RIGHT TOOL. Don't force small tools and attachment to do the job of a heavy-duty tool. Don't use tools for purpose not intended, for

example, don't use electric curricular saw for cutting logs or tree limbs.

• DRESS PROPERLY. Don't wear loose clothes on jewellery. They can be caught in moving parts. Rubber gloves and non-skid footwear are

recommended when working out. doors. Wear protective hair covering to contain long hair.

• USE SAFETY GOGGLES. Always wear safety goggles. If dust is produced use the special masks.

• DONT ABUSE CABLES. Never carry tool by cable or rank it to disconnect it from socket. Keep cable from heat, oil, and sharp edges.

• DON’T OVERREACH. Keep proper footing and balance at all times.

• MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance. Follow instruction for lubricating accessories

inspect tool cords periodically and replace if damaged. Keep handles dry clean and free from oil and grease.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CS-355 Cold Cut Off Saw

E&OE © Baumr-AG 4

• DISCONNECT TOOLS. When not in use, before servicing, and when changing accessories such as blades, bits, and cutters.

• KEMOVE ADIUSTING KEYS AND WRENCHES. Form the habit of checking to see that keys and adjusting wrenches are removed form tool

before turning it on.

• AVOID UNINTENTIONAL STARING. Don't carry plugged-in tool with finger on switch. Make sure the switch is off when connecting the plug to

the socket.

• USE EXTENSION CORD. If an extension cord is required, always check that its cross- section measurement is equal to or greater than that of

the tool capabilities and so marked.

• STAY ALERT. Watch what you are doing. Use common sense. Do not operate tool when you are tired.

• CHECK DAMAGE PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it

will operate properly and perform its intended function, check for alignment of moving parts, blinding of mooring parts, breakage of moving parts,

mounting and any other conditions that may affect is operation. A guard or other part that is damaged should be properly repaired or replaced by

a qualified service centre unless otherwise indicated elsewhere in the instruction manual. Have defective switches replaced by a qualified service

centre. Do not use tool if switch does not turn it on and off.

• CHECK THE VOLTAGE. Do not plug the electric tool into the mains until you have checked that the voltage shown on the date plate corresponds

to the voltage available.

• REPLACE PARTS. Do not plug the electric into the mains until you have checked that the voltage shown on the data plate corresponds to the

voltage available.

• HAVE YOUR TOOL REPAIRED BY AN EXPERT. This electric tool is in accordance with the relevant safety regulations. Repairing of electric tool

may be carried out only by expert. Otherwise, it may cause considerable danger to the user.

Additional Safety Regulations

•

If the tool you purchased is Class I, for your safety, ensure that the housing is correctly grounded before operation, as should be the power

supply. If an extension cord is required, use only a three-core cord, plug, and socket that have been properly grounded.

• Before plugging this tool into the mains, ensure that the cutting wheel is securely tightened, the special spanner has been removed from the tool,

and the lock pin behind the protection cover has been removed from its locked position.

• Before moving this tool, fixing parts, adjusting the cutting angle of the workpiece, or replacing the cutting wheel, please turn off the switch and

remove the plug from the socket.

• Before operating, ensure that the safety protection devices are functioning properly.

• When operating this tool, it is forbidden to stop the cutting wheel by touching it with your hand.

• When cutting a workpiece, do not start operating until you confirm that the workpiece has been securely fixed in the vise.

• Before the cutting wheel contacts the workpiece, you must wait until the cutting wheel reaches maximum speed.

• Turn off the switch immediately after finishing cutting, then allow the cutting wheel to return to its original speed.

• Keep the cutting wheel sharp. Replace it when it has been worn down by approximately 1/3.

• The air vent of the tool should be cleaned regularly to ensure the motor can cool normally.

• Please use a reinforced fibre cutting wheel with a safety peripheral speed over 80 m/s. The cutting wheel should be perfect and intact. It should

not emit a sound of breakage or crack when tapped lightly with a wooden hammer.

• Please lock the head in the lowest position with the chain during the storage and transportation of the tool.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CS-355 Cold Cut Off Saw

E&OE © Baumr-AG 5

Safety Symbols

The product may have safety warning labels attached to it, explained below. Understand the symbols on your

product and their meanings. If any stickers become unreadable, unattached etc., replace them.

Flammable Material Hazard

Flammable liquids, gases, or

substances etc may present.

Avoid ignition sources and open

flames. Danger of fire.

Read User Manual

Read and fully understand

product safety warnings,

operation, procedures etc before

using the product.

Use Hand Protection

Wear appropriate hand protection

and take due care as the product

or use of the product may present

hand hazards.

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Electrocution / Electrical Shock

Hazard

High voltage or high current

electricity may be present or

required by the product. Take

due care when handling electrical

products, cables, plugs and

leads. Electrical shock can be

fatal.

Toxic Fumes / Dust Hazard

Using the product or by-products

from use may produce fumes,

smoke or particles that could be

harmful if inhaled. Wear

appropriate breathing protection

and have adequate ventilation.

Explosive Material Hazard

Combustible liquids, gases, or

substances etc may be present.

Avoid ignition sources and open

flames. Danger of explosion.

Cutting / Amputation Hazard

The product may have blades,

edges or mechanical devices that

can cause severe cut injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Crush Hazard

The product may have blades,

edges or mechanical devices that

can cause severe crush injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Single Operator Only

The product must be operated by

a single person only. More than

one person operating the product

may introduce additional hazards.

Use Face Protection

Wear appropriate full-face

protection and take due care as

the product or use of the product

may present face and eye

hazards.

Use Foot Protection

Wear appropriate foot protection

and take due care as the product

or use of the product may present

foot hazards.

Use Eye / Ear / Head Protection

Wear appropriate eye and / or

ear and / or head protection and

take due care as the product or

use of the product may present

eye, hearing, and head hazards.

Running Hazard

Do not run on or near the product

as doing so may present a fall

hazard.

Diving Hazard

Do not dive into the product as

doing so may present a neck /

head injury hazard.

Adult Supervision Required

Always supervise children and

other users of a product to

prevent drowning or injury.

Skin Penetration / Puncture

Hazard

The product may produce

pressure, emit liquids or objects

that can cause severe injury to

fingers, limbs, blood etc. Take

due care when handling and

using the product.

Hot Surface Hazard

Be aware that the product may

produce high temperatures and

hot surfaces that can cause burn

injuries.

Flying Debris Hazard

Be aware that the product or use

of the product may present

hazards produced by flying

debris. Wear appropriate clothing

and protective devices.

Moving Parts Hazard

Be aware that the product

contains or uses mechanical

devices that move or rotate.

Always wait for moving parts to

stop fully before handling the

product, adjusting, maintenance

etc.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CS-355 Cold Cut Off Saw

E&OE © Baumr-AG 6

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Pull Hazard

Be aware that the product

contains or uses mechanical

devices that can pull in objects

and can cause severe injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Slope / Fall Injury Hazard

Be aware that using the product

on sloping surfaces or in slippery

conditions may present additional

dangers from falls and contact

with blades, moving parts, hot

surfaces etc.

"Slam Dunk" Warning

Do NOT attempt "slam dunk"

manoeuvres as this may result in

severe injury due to falling,

product breakage or collapse etc.

Electrocution / Electrical Shock

Hazard - Outdoor

High voltage or high current

electricity may be present or

required by the product. Do NOT

use in rain, damp, or wet

conditions. Electrical shock can

be fatal.

Electrocution / Electrical Shock

Hazard - Disconnect

High voltage or high current

electricity may be present or

required by the product. Always

disconnect the product from the

electrical supply before handling

the product, adjusting,

maintenance etc.

Power Line Electrocution

Hazard

High voltage / high current power

lines may be present. Use

extreme caution to avoid contact

or interference with power lines.

Electrical shock can be fatal.

"Kick-Back" Hazard

High level of "kick-back" hazard

that can cause the machine to

suddenly rotate towards operator.

Kick-back injury can be fatal.

Winch Operator Position

Hazard

Do NOT stand between winch

and load. Do NOT use winch to

move people.

Winch Lift Hazard

Do NOT LIFT load vertically. Use

machine to PULL only.

Cable Hazard

Ensure that load bearing cable is

not kinked or knotted.

Winch Cable Hazard

Ensure that there is a minimum

number of cable coils on

winching mechanism.

Winch Hook Hazard

Carry hook to load – do NOT

throw or run.

Flash / Blinding Hazard

Wear appropriate eye protection

for welding. Direct exposure to

weld arcs may cause permanent

eye injury.

Laser Hazard

Laser may be in use – do NOT

look directly at laser or allow

others to.

Choking Hazard

Children under 8 yrs. Can choke

or suffocate on small parts. Adult

supervision required.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CS-355 Cold Cut Off Saw

Table of Contents

Safety ............................................................................................................................................................. 2

Safety Symbols ........................................................................................................................................................... 5

Operation ....................................................................................................................................................... 8

Preparation Before Operating ..................................................................................................................................... 8

Operating the Tool ...................................................................................................................................................... 8

Adjustment of Cutting Angle ....................................................................................................................................... 8

Cutting Wide Workpieces ........................................................................................................................................... 8

Cutting Wheel Replacement ....................................................................................................................................... 9

Maintenance ................................................................................................................................................ 10

Specifications ............................................................................................................................................. 10

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CS-355 Cold Cut Off Saw

Operation

Preparation Before Operating

1. Place the tool on flat ground or a work table. It can also be secured to the work table using the holes in the

base.

2. Adjust the chain to keep the cutting wheel in the highest position.

Operating the Tool

1. Place the workpiece on the base and secure it firmly in the vise by turning the vise handle (3). Ensure the

workpiece does not move or loosen during cutting.

2. Turn on the switch (6) before the cutting wheel contacts the workpiece and wait until the cutting wheel

reaches maximum speed. Then, slowly press down the handle (7) to begin cutting.

3. Immediately turn off the switch (6) once the cutting is finished. Gradually release the handle (7) to allow the

cutting wheel to return to its original position.

Adjustment of Cutting Angle

The vise of the tool can be adjusted from 0 degrees to 45 degrees to facilitate angle cutting. To adjust the cutting

angle, first loosen the fixed screw (2) on the vise, turn the vise plate (1) to the desired angle according to the

angle marks, and then tighten the fixed screw (2). Please refer to Figure 1.

Cutting Wide Workpieces

The vise of the tool can be moved backward by 35mm to accommodate wider workpieces. When adjusting,

loosen the fixed screw on the vise, move the vise towards the back of the tool, and then insert the fixed screw

into the assembly hole to secure the vise. Please refer to Figure 2.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CS-355 Cold Cut Off Saw

Figure 2

Cutting Wheel Replacement

1. Unplug the tool from the power socket.

2. Release the handle to return the cutting wheel to its highest position.

3. Push the lock pin located behind the protection cover to lock the spindle, making it immovable.

4. Open the side cover of the protection cover.

5. Loosen the hexagon bolt (8) with the special spanner, and then sequentially remove the flange washer (7),

outer flange (6), and cutting wheel (5).

6. Install the new cutting wheel, outer flange, and flange washer in the reverse order, then securely tighten the

bolt (8). Release the lock pin and ensure the rotor is set free. Replace the side cover to its original position.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CS-355 Cold Cut Off Saw

Maintenance

Please check the carbon brushes of the tool regularly. When the carbon brushes are worn down to 5-6mm, they

must be replaced in pairs. To change them, remove the brush holder cap at the back of the motor housing using

a screwdriver, and then take out the worn carbon brushes. After replacing the brushes, allow the tool to run idle

for 10 minutes.

Specifications

Voltage 240V 50Hz

Power 2400W

Plug Standard Australian 10A

Cord Length 210 cm

Blade Type Abrasive Resin Composite (355 x 3 x 25.4mm)

Blade Diameter 355mm, 14 inches

Speed 3800 RPM

Max Cut

Rectangular:



90 degrees: 210 x 85mm



45 degrees: 135 x 43mm

Square:



90 degrees: 120 x 120mm



45 degrees: 85 x 85mm

Round Pipe:



90 degrees: 130mm



45 degrees: 90mm

Angle steel:



90 degrees: 200 x 200mm



45 degrees: 130 x 130mm

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Some experts believe that the incorrect or prolonged use of almost any

product may cause serious injury or death. To help reduce your risk of

serious injury or death, refer to the information below. For more information,

see www.datastreamserver.com/safety



Consult all documentation, packaging,

and product labelling before use. Note

that some products feature

documentation available online. It is

recommended to print and retain the

documentation.



Before each use, check the product for

loose/broken/damaged/missing parts,

wear, or leaks (if applicable). Never use a

product with

loose/broken/damaged/missing parts,

wear, or leaks.



Products must be inspected and serviced

(if applicable) by a qualified technician

every 6 months. This is based on

average residential use by persons of

average size and strength, and on a

property of average metropolitan size.

Use beyond these recommendations may

require more frequent

inspections/servicing.



Ensure that all users of the product have

completed a suitable industry recognised

training course before being allowed

access to the product.



The product has been supplied by a general merchandise

retailer that may not be familiar with your specific

application or description of application. Be sure to attain

third-party approval from a qualified specialist for your

application before use, regardless of any assurances from

the retailer or its representatives.



This product is not intended for use where fail-safe

operation is required. As with any product (for example,

automobile, computer, toaster), there is the possibility of

technical issues that may require the repair or

replacement of parts, or the product itself. If the possibility

of such failure and the associated time it may take to

rectify could in any way inconvenience the user, business,

or employee, or financially affect the user, business, or

employee, then the product is not suitable for your

requirements. This product is not intended for use where

incorrect operation or a failure of any kind, including but

not limited to, a condition requiring product return,

replacement, parts replacement, or service by a

technician may cause financial loss, loss of employee

time or an inconvenience requiring compensation.



If this product has been purchased in error when

considering the information presented here, contact the

retailer directly for details of their returns policy, if

required.

diagrams, or images may be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying, scanning, or recording, or any information storage and retrieval system,

without express permission or consent from the publisher.

BAUMR-AG SAWMCTBM3CVA Metal Cut Off Saw 2400W

Product's Documents

Product manual

Specifications

BAUMR-AG SAWMCTBM3CVA Questions and Answers