TIG WELDING GAUNTLETS - PAIR
MODEL NO: SSP142.V4
1. INTRODUCTION
Quality goat skin TIG welding leather gauntlets with 160mm split cow leather cu. 330mm Length. Conforms to BS EN 388 and BS EN
12477:2001. Size range: 9,10, 11.
Notied Body: ITS Testing Services (UK) Limited, Ventre Court, Meridian Business Park, Leicester, LE19 1WD
Type Examination Certicate Number: LEC FI00339435
Approved Body No: 0362
2. SAFETY
9 For multilayer gloves that can be separated, the performance of levels are only applicable to the whole glove including all layers.
8 DO NOT use where there is risk of entanglement by moving parts.
9 When gloves are intended for arc welding: these gloves do not provide protection against electric shock caused by defective or live
working equipment. Note that electrical resistance is reduced if the gloves are wet, dirty or soaked with sweat. This could increase the
risk of electric shock.
9 Protection is only given to the palm of the hand, the cu will give adequate protection against small splashes of molten metal.
9 There are substances in the glove which are known to cause allergies. A list of raw substances is available upon request.
9 Type B gloves are recommend when high dexterity is required, as for TIG welding. Type A gloves are recommended for other welding
processes.
9 There is no standardized test method at present for detecting UV penetration of materials for gloves, but the current methods of
construction of protective gloves for welders do not normally allow penetration of UV radiation.
3. PERFORMANCE
Mechanical Risks
EN 388
2111X
Abrasion Resistance 1 (on 4 maxi) The numbers indicate the
performance level of the gloves.
1 = lowest 4 = highest 5 =
highest for blade cut resistance
‘X’ indicates that the glove has
not been submitted to the test or
the test method appears not to
be suitable for the glove design
or material.
Blade Cut Resistance 1 (on 5 maxi)
Tear Resistance 1 (on 4 maxi)
Puncture Resistance 1 (on 4 maxi)
Cut Resistance Method (EN ISO 13997) X (A to F)
Thermal Risks (Heat/Flame)
EN 407
412X4X
Limited Flame Spread 4
Contact Heat 1
Convective Heat 2
Radiant Heat X
Small drops of molten metal 4
Large drops of molten metal (if
applicable)
X
Protective Gloves for Welders
EN 12477
Burning Behaviour B Suitable for high dexterity tasks.
Contact Heat B
Small splashes of molten metal B
4. INSTRUCTIONS FOR USE
4.1. Place glove over hand tting the thumb and ngers in the appropriate positions, making sure the glove is tted comfortably to carry out
the task at hand.
4.2. Remove by pulling the glove upward from the ngers.
5. MAINTENANCE
8 DO NOT wash or tumble dry.
9 The packaging provided with the glove is suitable for the required transport.
9 This product does not have an expiry date, but should be replaced when worn/damaged.
REFER TO INSTRUCTIONS
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
SSP142.V4 Issue 1 18/09/23Original Language Version
© Jack Sealey Limited
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When
the product becomes completely unserviceable and requires disposal, drain any uids (if applicable) into approved
containers and dispose of the product and uids according to local regulations.
REGISTER YOUR
PURCHASE HERE
This document has been drawn up according to Regulation (EU) 2016/425 as amended to apply to GB for Personal Protective
Equipment. The declaration of conformity can be accessed at www.sealey.co.uk.
SSP142.V4 Issue 1 18/09/23Original Language Version
© Jack Sealey Limited
EU | Sealey EU Ltd, Farney Street, Carrickmacross, Co. Monaghan, A81 PK68 Ireland
UK | Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 sales@sealey.co.uk www.sealey.co.uk
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specications and component parts
without prior notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please
email or call our technical team on technical@sealey.co.uk or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
