LEATHER WELDING GAUNTLETS
MODEL NO: SSP151.V2
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
I
MPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. INTRODUCTION
Heavy-duty traditionally designed extra-large welding gauntlets providing excellent protection against spatter and heat. Manufactured
from split cow hide leather with Kevlar® stitching, cotton lined cuff with a soft comfortable fl eece lining. Durability is enhanced by
additional leather, stitched over the palm area of the hand. These gauntlets cannot be used for arc welding. Five year storage life in
cool, dry conditions. In case of wear/damage/deterioration the gloves must be scrapped.
Certifi ed to EN 12477, Type ‘A’. Rated to EN 388 - 3134X and EN 407 - 41314X.
It meets the requirements of the PPE Regulation 2016/425 applicable from April 21st, 2018: innocuousness, comfort, solidity.
It has been subject to a UE-type Examination performed by: C.T.C. (OO75)
4, rue Hermann Frenkel
69367 LYON Cedex 07
FRANCE
2. SAFETY
WARNING! This glove doesn’t protect against temperatures over 100
o
C
WARNING! This glove is not suitable for arc welding.
DO NOT wear these gloves when there is a risk of entanglement by moving parts of machines.
2.1. This model does not contain any substances at levels that are known to, or suspected to, adversely aff ect user hygiene or health.
2.2. The protection against risks or hazards which are not mentioned in this document is not warranted.
2.3. The levels of performance mentioned are only valid for the palm of the glove.
2.4. The levels of performance mentioned are only valid for new gloves, not washed, nor regenerated.
2.5. These levels of performance are obtained from the tests done according to conditions defi ned by the applicable standards.
2.6. Before use the glove shall be visually controlled, in case of deterioration, the gloves must be scrapped (abrasion, cut, tear).
2.7. For gloves with diff erent layers of material, the performance levels are warranted only for the whole glove.
2.8. These gloves do not provide protection against electric shock caused by defective or live equipment, and the electrical resistance is
reduced if the gloves are wet, dirty or soaked with sweat, this could increase the risk.
2.9. There is no standardised test method at present for detecting U.V penetration of materials for gloves, but the current method of
construction of protective gloves for welders do not normally allow U.V radiation penetration.
2.10. With arc welding installations, it is not possible to protect all parts conducting the welding voltage against direct contact for operational
reasons. The gloves do not protect again electrical risks due to defected equipment or moisture.
2.11. For gloves with two or more layers the overall classifi cation does not necessarily refl ect the performance of the outermost layer.
3. APPLICABLE STANDARDS
This glove meets the requirements of the standard EN 420 : 2003 + A1 : 2009 < General requirements for work glove > Dexterity : 2
Moreover, this glove has been designed for the following applications :
Mechanical Hazard
EN 388 : 2016
3134X
Abrasion Resistance 3 (on 4 maxi) ‘X’ indicates that the glove has
not been submitted to the test or
the test method appears not to
be suitable for the glove design
or material.
Blade Cut Resistance 1 (on 5 maxi)
Tear Resistance 3 (on 4 maxi)
Puncture Resistance 4 (on 4 maxi)
Cut Resistance Method (EN ISO 13997) X (A to F)
Impact Protection -
Thermal Risk
EN 407 : 2004
41314X
Burning Behaviour 4 (on 4 maxi)
Contact Heat 1 (on 4 maxi)
Convective Heat 3 (on 4 maxi)
Radiant Heat 1 (on 4 maxi)
Small Splashes of Molten Metal 4 (on 4 maxi)
Large Quantities of Molten Metal X (on 4 maxi)
READ INSTRUCTIONS
BEFORE USE
SSP151.V2 Issue 1 19/07/23
Original Language Version
© Jack Sealey Limited
SSP151.V2 Issue 1 19/07/23
Original Language Version
© Jack Sealey Limited
EU | Sealey EU Ltd, Farney Street, Carrickmacross, Co. Monaghan, A81 PK68 Ireland
UK | Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 sales@sealey.co.uk www.sealey.co.uk
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifi cations and component parts
without prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When
the product becomes completely unserviceable and requires disposal, drain any fl uids (if applicable) into approved
containers and dispose of the product and fl uids according to local regulations.
EN12477: 2001/A1:2005: Type A: is recommended for applications without high dexterity.
The Declaration of Conformity (DOC) can be found at: www.sealey.co.uk
4. MAINTENANCE
4.1. STORAGE
4.1.1. Store the gloves in their original packaging.
4.1.2. Store the gloves in normal temperature and humidity conditions.
4.1.3. Store the gloves in clean, covered and ventilated premises.
4.2. MAINTENANCE
4.2.1. The gloves should be inspected before each use, and replaced if damaged.
4.3. This PPE is subject to ageing and has a 5 year shelf life when stored in appropriate conditions.
