Loading ...
Loading ...
Loading ...
7
8
Operaon Cauon and Device Maintenance
Specificaon
Replace Baeries
- All the electronic operaon should be strictly compliance with the electrical safety regulaons, fire prevenon regula-
ons and other related regulaons in your local region.
- Do not drop the device or subject it to physical shock, and do not expose it to high electromagnesm radiaon. Avoid
the equipment installaon on vibraons surface or places subject to shock (ignorance can cause equipment damage).
- Please make sure that the power has been disconnected before you wire, install or dismantle the device.
- If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please
contact the service center.
- Do not drop the device or subject it to physical shock, and do not expose it to high electromagnesm radiaon. Avoid
the equipment installaon on vibraons surface or places subject to shock (ignorance can cause equipment damage).
- Do not place the device in extremely hot (refer to the specificaon of the device for the detailed operaon tempera-
ture), cold, dusty or damp locaons, and do not expose it to high electromagnec radiaon.
- The device for indoor use shall be kept from rain and moisture.
Exposing the equipment to direct sun light, low venlaon or heat source such as heater or radiator is forbidden (igno-
rance can cause fire danger).
- Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a
malfuncon however), and affecng the endurance of sensor at the same me.
- Improper use or replacement of the baery may result in hazard of explosion. Replace with the same or equivalent type
only. Dispose of used baeries according to the instrucons provided by the baery manufacturer.
- Do not expose the device to the corrosive gas. Otherwise the equipment damage may occur.
- Do not expose the device to the explosive situaon.
4
Hangzhou Hikvision Digital Technology CO.,Ltd. No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China
The device is self powered from the manufacturer.
Replace all baeries at the same me.
Do not mix old and new baeries.
CAUTION
RISK OF EXPLOSION IF BATTERY IS
REPLACED BY AN INCORRECT TYPE
DISPOSE OF USED BATTERIES
ACCORDING TO THE INSTRUCTIONS
CHEMICAL BURNING DANGER
DO NOT SWALLOW THE BATTERY
KEEP NEW AND USED BATTERIES
AWAY FROM THE CHILDREN
INSTALL THE BATTERIES ACCORDING
TO THE POLARITY MARK ON THE
BATTERY HOLDER. THE OPPOSITE
POLARITY MAY CAUSE DEVICE
DAMAGE
DO NOT REVERSE THE POLARITY OF
THE BATTERY
Frequency 868 MHz
Metod Two-way communicaon
Distance 1.6 KM
Indicator Red/Green/Amber
Strobe light Red/Blue
Power Baery (default power supply method)
Consumpon
Quiescent Current: 40uA
Max. 3 V/4A (alerts in volume level 3 )
Low Baery Cut Off
2.45 V
Voltage Range
Fully charged (new) to 2.45V DC (baery)
Baery life span
3 CR123A, 3 years in work status (triggered every two weeks and
alerng 90 s for each triggering)
Power switch Power switch
Tamper switch Front and rear tamper-proof
Decibel 90 to 110 db
Max. sound duraon
15min
（
900s
）
Operaon
Temperature
-10 °C to 40 °C (14 °F to 104 °F)
Operaon Humidity 10% to 90%
Dimension (W × H ×
D)
88× 88 × 32 mm (3.46" ×3.46" × 1.26"）
Weight 169.5g
Installaon Wall mounng
General
RF
Indicaon
Power
Interface
Buzzer