Loading ...
English
IMPORTANT
SAFETY
INSTRUCTIONS
When using an electric product, basic
precautions should always be followed,
including the following:
Read all instructions before using this
product.
DANGER
To reduce the risk of electric shock:
- Do not reach for a corded product that
has fallen into water. Unplug immediately.
- Power plug and the accessories
connected to it are not for immersion or
for use in shower.
- Do not use an extension cord with this
product.
- Do not place or store the product where
it can fall or be pulled into a tub or sink,
water or other liquid while plugged in.
- Always unplug this product from the
electrical outlet immediately after use,
except when product is (re)charging.
- Unplug and remove power supply cord
from the product before cleaning.
- The batteries used in this product may
present a re or chemical burn hazard
if mistreated. Do not disassemble, heat
above 100°C (212°F) or incinerate.
WARNING
To reduce the risk of burns, re, electric
shock, or injury to persons:
- Close supervision is required when this
product is used by, on, or near children,
or persons with limited physical, sensory,
or mental capabilities or invalids.
- Use this product only for its intended
household use as described in this manual.
Do not use attachments not recommended
by Philips North America LLC.
- This product is only intended for shaving
and trimming body parts below the
neckline. Do not use it to shave or trim
facial or scalp hair.
- Never operate this product if it has a
damaged power cord or charging plug,
if it is not working properly, if it has been
dropped or damaged, or dropped into
water while plugged in. For assistance
call 1-800-243-3050.
- Keep the product, cord, charging plug
and any attachments away from heated
surfaces.
- Never drop or insert any object into any
opening.
- Do not use the adapter in or near a power
outlet that contains an electric air freshener
to prevent damage to the adapter
.
- Do not charge, clean or plug in product
outdoors or operate where aerosol
(spray) products are being used or where
oxygen is being administered.
- Always check cutters, foil, cutting unit and
guards before using the product. Do not
use the product if cutters, cutting unit or
guards are damaged, as injury may occur.
- Always attach power cord to product rst,
then to outlet. Be certain plug is inserted
rmly into product up to mark indicated
on plug. To disconnect, turn product o
then remove power cord from outlet.
- Keep the power cord dry at all times.
Do not handle with wet hands.
- Use only the cord provided to charge and
(re)charge the product.
- Never put the product in direct sunlight or
store at a temperature above 140°F (60°C).
- This product is water-safe and can be
rinsed under running tap water or used in
shower. Do not submerge product in water.
- To prevent possible damage to the cord,
do not wrap cord around the product.
- This product is for use on human hair
only. Do not use the product for any
other purpose.
- Always store the product, attachments
and power cord in a moisture-free area.
Make sure the cord is disconnected from
the product.
- Do not attempt to open the product
to remove or replace the built-in
rechargeable battery.
- Only use the power plug and other
accessories supplied with the product.
SAVE THESE
INSTRUCTIONS
IMPORTANT: The power plug contains a
transformer. Do not cut o the power plug
to replace it with another plug as this will
cause a hazardous condition.
Introduction
Congratulations on your purchase and
welcome to Philips Norelco!
To fully benet from the support that Philips
Norelco oers, register your product at
www.norelco.com/register.
3mm
(1/8in.)
5mm
(3/16in.)
7mm
(9/32in.)
1
4
2
3
5
8
6
7
10
9
1
General description (Fig. 1)
1 Trimming guard (3mm/ 1/8in.)
2 Trimming guard (5mm/ 3/16in.)
3 Trimming guard (7mm/ 9/32in.)
4 Shaving unit
5 Shaving foil
6 On/o button
7 Battery status indicator
8 Back shaving attachment
9 Power plug
10 Small plug
This symbol indicates that the
product can be used in the bath
or shower.
Charging
Battery status indications
- When the battery is almost empty, the
battery status indicator ashes orange
(Fig. 2).
- When the product is charging, the battery
status indicator ashes green (Fig. 3).
- When the battery is fully charged, the
battery status indicator lights up green
continuously.
Note: After approx. 30 minutes, the light
goes out automatically.
Charging
Charging takes approx. 1 hour. Charge the
product before you use it for the rst time
and when the display indicates that the
battery is almost empty.
- Charging, recharging or using the product
at temperatures below 40°F (4,5°C) or
higher than 95°F (35°C) adversely aects
the lifespan of the battery.
- If the product is subjected to a major
change in temperature, pressure or
humidity, let the product acclimatize for
30 minutes before use.
1 Make sure the product is switched o.
2 Insert the small plug into the product
(Fig. 4) and put the power plug in any
120V AC outlet.
3 After charging, remove the power plug
from the wall outlet and pull the small
plug out of the product.
Note: An adapter plug may be necessary for
cord usage in some foreign countries. Use
an attachment plug adapter of the proper
conguration for power outlet.
Operating time
When the product is fully charged it has a
cordless operating time of up to 60 minutes.
Using the product
You can use the product wet or dry to shave
or trim hair on all parts of the body below
the neckline (Fig. 5, Fig. 6).
Always check the product and all accessories
before you use it. Do not use the product or
any accessory if it is damaged, as this may
cause injury. Always replace a damaged
part with one of the original type.
-
Use this product for its intended household
use as described in this manual.
- For hygienic reasons, the product should
only be used by one person.
- Trimming is easier when the skin and hair
are dry
Note: This product is for cordless use only.
Switching the product on and o
1 Press the on/o button once to switch
the product on or o (Fig. 9).
Attaching and detaching guards
1 To attach a guard, snap the front part of
the guard onto the teeth and push the
projection at the back of the guard into
the product (‘click’).
2 To detach a guard, carefully pull the back
part o the product and then click it o
the cutting element.
Trimming length settings
The trimming guards allow you to cut hair to
3 dierent length settings.
Guard size
indication
Hair length after
trimming
3 3mm/ 1/8in.
5 5mm/ 3/16in.
7 7mm/ 9/32in.
Trimming
- If you are trimming for the rst time, be
careful. Do not move the product too fast.
Make smooth and gentle movements.
- When you trim for the rst time, use
trimming guard #7 (9/32 in./7mm) to
familiarize yourself with the product.
- Since all hairs do not grow in the same
direction, you may want to try dierent
trimming positions (i.e. upwards,
downwards, or across). Practice is best
for optimum results.
- Always make smooth and gentle
movements and be sure the surface of
the guard always stays in contact with
your skin.
- Body hair can be trimmed wet or dry,
however dry is preferable because wet
hair tends to stick to the body.
- When trimming sensitive areas, always
use a trimming guard
Trimming
1
Snap the desired trimming guard onto the
product (Fig. 10). Trim against the hair grain
for optimal performance (Fig. 7, Fig. 8).
2 Press the on/o button to turn on the
product (Fig. 11).
3 Move the product against the direction of
hair growth.
Note: Make sure that the at part of the
trimming guard is always fully in contact
with the skin.
4 Turn o and clean the product after each
use (see ‘Cleaning’).
Shaving
Do not use this shaving unit to shave or
trim facial or scalp hair.
- When shaving sensitive areas for the
rst time, you may feel some discomfort,
irritation or reddening of the skin. This is
normal as your skin needs time to adjust
to shaving.
- If your hair is longer than 13/32in. (10 mm),
trim hair to a length of 1/8in. (3mm) rst
for optimum shaving results.
- For dry use, be certain that your skin is clean
and dry before using the shaving unit.
- For wet use, prepare your skin with
lathered soap or shaving foam before
using the shaving unit.
1 Remove any trimming guard from the
product.
2 Press the on/o button to turn on the
product (Fig. 11).
3 Stretch your skin taut with your free hand
(Fig. 12). Gently press the shaving unit to
skin and move it slowly and smoothly
against the direction of the hair growth
(Fig. 13, Fig. 14).
- Do not press too hard. Too much
pressure can distort the foil and cause
skin irritation.
- Make sure the shaving unit is always in
full contact with your skin.
- The shaver is bi-directional, which
means that you can shave by moving the
appliance up and down. Shave against
the hair grain for optimal performance.
4 Switch o and clean the product after
each use Cleaning (see ‘Cleaning’).
Shaving with the back shaving
attachment
Note: The back shaving attachment is
suitable for both wet and dry use.
1 Press and hold the release button (1)
and open the back shaving attachment
(Fig. 16) (2) in the preferred setting.
2 Place the bottom of the product in
the lower part of the back shaving
attachment. Then press the top against
the top part of the holder until it locks
into place with a click (Fig. 17).
3 Press the on/o button to turn on the
product (Fig. 11).
4 Shave your back by moving the back
shaving attachment up and down by its
handle (Fig. 18).
Note: For ease of use, the back shaving
attachment can be folded to dierent
angles (Fig. 19). Use a smaller angle to
shave your lower back (Fig. 20).
5 To remove the product from the back
shaving attachment, pull the top of the
product towards you until it unlocks from
the holder (Fig. 21).
6 To close the back shaving attachment,
press and hold the release button (1) and
push the handle against the holder (2)
(Fig. 22).
Cleaning
Clean the product after every use.
Never use scouring pads, abrasive cleaning
agents or aggressive liquids such as
gasoline or acetone to clean the product.
Never dry trimmer or shaving foil head
with a towel, brush or tissue, as this may
cause damage.
1 Turn o the product.
2 Remove any trimming guard from the
product.
3 Rinse the back shaving attachment and
product handle under warm water and
wipe dry with a dry cloth.
4 Remove the shaving foil head by pulling
it o the product (Fig. 24).
- Hold the shaving foil head by the plastic
housing only.
5 Rinse the shaving foil head with warm
running tap water (Fig. 25).
6 Allow the shaving foil head to air dry
completely.
- Never dry trimmer or shaving foil head
with a towel, brush or tissue, as this may
cause damage.
7 Rinse the hair chamber under warm
running tap water to remove any residual
debris (Fig. 26).
8
Reattach the shaving foil head by snapping
it back onto the product (Fig. 27). You
will
hear a click.
This product has no other user-serviceable
parts. For assistance call 1-800-243-3050.
Storage
- Be sure the product is switched o.
Remove cord from outlet and the
product before storing it in a safe, dry
location where it will not be crushed,
banged, or subject to damage.
- Do not wrap cord around the product
when storing.
- Store cord in a safe location where it will
not be cut or damaged.
- Do not place or store the product where
it can fall or be pulled into a tub or sink,
water or other liquid while plugged in.
Replacement
Replacing the shaving foil head
For maximum shaving performance, we advise
you to replace the shaving foil head and
cutters every year (TT2000). If shaving head
foil and cutters are worn or damaged, do not
use the product and replace immediately.
Always replace the shaving foil head and
cutters with original Philips Norelco shaving
foil head Accessories (see ‘Accessories’).
1 Switch o the product and disconnect it
from the wall outlet.
2 Remove the shaving foil head by pulling
it o the product (Fig. 24).
Note: The foil is delicate. Handle the shaving
unit with care.
3 Place the new shaving foil head on the
product by snapping it into place (Fig. 27).
You will hear a click.
4 After replacing the shaving foil head,
check that the shaving head is rmly
attached before using product.
Accessories
Replacement parts may be purchased on
our website www.philips.com/store.
For maximum product performance,
replace shaving foil head once a year.
- Model BG2000 Philips Norelco
Replacement Shaving Foil Head.
Assistance
For assistance, visit our website:
www.philips.com/support or call toll free
1-800-243-3050.
Online information is available 24 hours
a day, 7 days a week.
Disposal
- This product contains a rechargeable
lithium-ion battery which must be
disposed of properly (Fig. 28).
- Contact your local town or city ocials
for battery disposal information.
You can also call 1-800-822-8837 or
visit www.call2recycle.org for battery
drop-o locations.
- For assistance, visit our website
www.philips.com/support or call
1-800-243-3050 toll free.
- Your product is designed and
manufactured with high quality materials
and components, which can be recycled
and reused. For recycling information,
please contact your local waste
management facilities or visit
www.recycle.philips.com
Full Two-Year Warranty
Philips North America LLC warrants this new
product (except foil, cutters and guards)
against defects in materials or workmanship
for a period of ve years from the date of
purchase, and agrees to repair or replace
any defective product without charge.
IMPORTANT: This warranty does not cover
damage resulting from accident, misuse or
abuse, lack of reasonable care, the axing
of any attachment not provided with the
product or loss of parts or subjecting the
product to any but the specied voltage or
batteries.*
NO RESPONSIBILITY IS ASSUMED
FOR ANY SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES.
In order to obtain warranty service, simply
go to www.philips.com/support for
assistance. It is suggested that for your
protection you return shipments of product
by insured mail, insurance prepaid. Damage
occurring during shipment is not covered by
this warranty.
NOTE: No other warranty, written or oral, is
authorized by Philips North America LLC.
This warranty gives you specic legal rights,
and you may also have other rights which
vary from state to state. Some states do
not allow the exclusion or limitation of
incidental or consequential damages, so the
above exclusion and limitations may not
apply to you.
*Read enclosed instructions carefully.
45-DAY MONEY-BACK GUARANTEE
If you are not fully satised with your
product send the product back and we’ll
refund you the full purchase price.
The product must be shipped prepaid
by insured mail, insurance prepaid, have
the original sales receipt, indicating
purchase price and date of purchase,
and the money-back guarantee return
authorization form enclosed.
We cannot be responsible for lost mail.
The product must be postmarked no later
than 45 days after the date of purchase.
Philips reserves the right to verify the
purchase price of the product and limit
refunds not to exceed suggested retail price.
To obtain money-back guarantee return
authorization form, call 1-800-243-3050
for assistance.
Delivery of refund check will occur 6–8 weeks
after receipt of returned product.
ENGLISH
25
28
12M
TT2000
23
26
24
27
1
2
4
16
3
15
2
14
1098
7
19
5
17
6
18
1311 12
1
2
222120
4222_100_8917_1_DFU-Leaflet_A7_v7.indd 8-14 11/09/17 10:21