TAA6219
6000 Series
Sports
Headphones
User manual
Register your product and get support at:
www.philips.com/support
1 Important safety instructions 2
Hearing safety 2
General information 2
2 Your On-ear solar-powered
headphones 4
What's in the box 4
Other devices 4
Overview of your Bluetooth
wireless headphones 5
3 Get started 6
Charge the battery
App download 7
Pair the headphones for the
�rst time 7
Pair the headphones with
another Bluetooth device 7
4 Use your headphones 8
Connect the headphones to a
Bluetooth device 8
Multi-point connection 8
Power on/off 8
Manage your calls and music 9
Gaming mode
(low latency mode) 9
Voice Assistant 9
LED indicator status 9
5 Reset the headphones 11
7 Notice 12
Declaration of conformity 12
Disposal of your old product
and battery 12
Remove the integrated battery 12
Compliance with EMF 12
Environmental information 13
Notice of compliance 13
8 Trademarks 15
9 Frequently asked questions 15
Contents
6 Technical data 11
2 EN
1 Important
safety
instructions
Hearing safety
Be sure to observe the following
guidelines when using your headphones.
• Listen at reasonable volumes for
reasonable periods of time.
• Be careful not to adjust the volume
continuously upwards as your
hearing adapts.
• Do not turn up the volume so high
that you can't hear what's around
you.
• You should use caution or
temporarily discontinue use in
potentially hazardous situations.
• Excessive sound pressure from
headphones and headphones can
cause hearing loss.
• Using headphones with both ears
covered while driving is not
recommended and may be illegal in
some areas.
• For your safety, avoid distractions
from music or phone calls while in
traffic or other potentially dangerous
environments.
General information
To avoid damage or malfunction:
Danger
To avoid hearing damage, limit the time you
use headphones at high volume and set the
volume to a safe level. The louder the volume,
the shorter the safe listening time is.
Caution
Do not expose headphones to excessive heat.
Do not drop your headphones.
Headphones shall not be exposed to dripping
or splashing. (Refer to the IP rating of speci�c
product)
Do not allow your headphones to be
submerged in water.
Do not charge your headphones when the
connector or socket is wet.
Do not use any cleaning agents containing
alcohol, ammonia, benzene, or abrasives.
Use a clean, damp cloth to clean your
headphones - especially the sound conduits and
the microphone holes - regularly and avoid
buildup of substances such as sweat or earwax.
If any sweat or water droplets are left in the
sound conduits, air holes or microphone holes,
the sound level will temporarily drop or cut out
entirely. This is not a malfunction. Use a soft,
damp cloth to dry the headphones thoroughly.
Alternatively, remove the earbud tips, turn the
sound conduits downward and gently tap the
headphones about �ve times on a dry cloth or
similar to remove any water collected inside.
Be sure the headphones are completely dry
before charging and using. Avoid using
disposable alcohol pads or other substances for
cleaning.
The integrated battery shall not be exposed to
excessive heat such as sunshine, �re or the like.
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or
equivalent type.
To achieve the speci�c IP rating, the charging
slot cover must be closed.
Disposal of a battery into �re or a hot oven, or
mechanically crushing or cutting a battery, can
result in an explosion.
Leaving a battery in an extremely high
temperature surrounding environment can
result in an explosion or the leakage of
�ammable liquid or gas.
A battery subjected to extremely low air
pressure may result in an explosion or the
leakage of �ammable liquid or gas.
Replacement of a battery with an incorrect type
risks severely damaging the headphones and
the battery (for example, in the case of some
lithium battery types).
If the headphones are not used for a long time,
the rechargeable battery will begin to lose its
charge. To avoid this loss, please fully charge
the battery at least once every three months.
3 EN
Operating and storage temperatures and
humidity
• Store in a place where the
temperature is between -20°C (-4°F)
and 55°C (131 °F) with up to 90%
relative humidity.
• 0-45 °C for charging operating
ambient temperature；
0-55°C for discharging operating
ambient temperature.
• Battery life may be shorter in high or
low temperature conditions.
To avoid risk of �re, the equipment is supplied
only by external power source which output
shall comply with PS1 (with output capacity less
than or equal to 15W).
2 Your On-ear
solar-powered
headphones
What's in the box
On-ear solar-powered headphones
Philips TAA6219
Quick start guide
Other devices
A mobile phone or device (e.g. notebook,
tablet, Bluetooth adapters, MP3 players
etc) which supports Bluetooth and is
compatible with the headphones (see
'Technical data' on page 11).
Congratulations on your purchase, and
welcome to Philips! To fully bene�t from
the support that Philips offers, register
your product at www.philips.com/support.
With these Philips headphones, you can:
• Enjoy convenient wireless handsfree
clear calls
• Enjoy and control great sound music
wirelessly
• Switch between calls and music
• Sunlight to electric light, these
headphones recharge whenever
they’re exposed to light
• Cool and comfy on-ear �t for Run,
walk, roller skate
Global Warranty
Safety lea�et
4 EN
Overview of your On-ear
solar-powered
headphones
Solar panel
Light source LED indicator
MFB (Multi-function button)
Volume + / Volume -
PWB (Power button)
Bluetooth / Charge LED indicator
Type C charging slot
Mic
1
2
3
4
5
6
7
8
2 3 4 5 6 7
1
8
EN 5
3 Get started
Charge the battery
Normally, a full charge takes 2.5 hours.
LED turns white during charging and
turns off when the headphones are
fully charged.
Tip
Where the temperature is lower than 0°C (32°F)
or higer than 45°C (113 °F) can’t charge
headphones what ever by power source or solar
energy.
Note
Before you use your headphones, place them in
the charging box and charge the battery for 2.5
hours for optimum battery capacity and lifetime.
Finish your call before charging. Connecting the
headphones to charge will power them off.
If the headset is not used for a long time, the
rechargeable battery will begin to lose its
charge. To avoid this loss, please fully charge the
battery at least once every three months.
Note
6 EN
Charging headphones by
power source
Charging headphones by any
sources of light
Plug one end of the USB-C cable (cable
not included) into the headphpone and
the other end into the power source.
Headphones built-in solar cell, it can be
charged by any sources of light.
Solar panel charging one hour in sunny
day can play music up to 2 hours.
EN 7
Pair the headphones with
your Bluetooth device for
the �rst time
The headphones remain in
pairing mode for 5 minutes.
1
2
Make sure that the headphones are
fully charged and powered off.
Press and hold PWB for 2 seconds
until the blue and white LED �ash
quickly.
Philips TAA6219
The following example shows you how
to pair the headphones with your
Bluetooth device.
Turn on the Bluetooth function of
your Bluetooth device, select
Philips TAA6219.
Enter the headphones' password
“0000” (4 zeros) if prompted. For
those devices featuring Bluetooth 3.0
or higher, there is no need to enter a
password.
1
2
Turn on the Bluetooth function of
your Bluetooth device.
Pair the headphones with the mobile
phone. For detailed information,
refer to the user manual of your
mobile phone.
3
4
App download
Scan the QR code/press 'Download'
button or search 'Philips Headphones' in
the Apple App Store or Google Play to
download the app.
The Philips Headphones App puts you in
charge of the music you are listening to.
You can customize the sound so that your
music and calling experience always best
suit your needs.
Get Connected
philips.to/headapp
Pair the headphones with
another Bluetooth device
If you want to pair another Bluetooth
device with the headphones, just put them
into pairing mode, press Volume + and
Volume - button for 4 seconds at the same
time, then discover the second device as
per normal pairing.
04" 04"
4 Use your
headphones
Connect the headphones
to your Bluetooth device
Turn on your mobile phone/
Bluetooth device.
Press and hold the PWB button to
turn the headphones on.
The blue LED is on for 1 second
The headphones are reconnected
to the last connected mobile
phone/ Bluetooth device
automatically. If the last one is not
available, the headphones will be
in pairing mode
If you turn on the mobile phone/Bluetooth
device or activate the Bluetooth feature after
turn on the headphones, you have to reconnect
the headphones and mobile phone/Bluetooth
device manually.
8 EN
If the headphones fail to connect to any
Bluetooth device within range of 5 minutes,
it will switch off automatically to save the
battery life.
Note
Tip
1
2
Note
When streaming audio from Device 1, receiving
a call from Device 2 will automatically pause
Device 1 playback. And the call will be routed
automatically to headphones.
Ending the call will automatically resume
playback from device 1.
Multi-point connection
Pairing
• Pairing the headphones to two
devices, e.g. mobile phone and
notebook.
Switch between device
• At anytime, you can only listen to
music from one device. Another
device will be for phone call.
• Pause the audio from one device
and then start play audio from the
another device.
Task
Turn the
headphones
on
Press and
hold 2s
Press and
hold 2s
Turn the
heaphones
off
Power on/off
Button
PWB
PWB
Operation
EN 9
Manage your calls and
music
Music control
Task Button Operation
MFBPlay or pause
music
Press once
Press once
Long press
Long press
Adjust volume
up
Press once
Adjust volume
down
Next track
Previous track
Call control
Task
Button
Button
Operation
Answer
Reject a call /
hang up a call
MFB
MFB
Press once
Press and
hold for one
second
Switch caller
during a call
Press once
Gaming mode
(low latency mode)
OperationTask
Gaming mode
on
Double
click
MFB
PWB
Gaming mode
off
Double
click
PWB
Charge LED indicator
Bluetooth LED indicator
When charging Indicator
Battery low
Charging White LED lights
up until fully
charged
Blue LED �ashes
until off
Waiting for
pairing
Connected to a
Bluetooth device
White LED blinks
once
Blue and white LED
�ashes alternately
Headphones
status
Indicator
LED indicator status
Bluetooth / Charge
LED indicator
Voice Assistant
OperationTask Button
Trigger Voice
(Siri/Google)
Assistant
Press &
holding for
1 second
Stop Voice
Assistant
Press once
MFB
MFB
10 EN
Light source LED indicator
At night or indoor
Rainy day
Near windows
(indoor) in sunny
day or cloudy day
One LED on
Two LEDs on
Sunny day
Three LEDs on
One LED �ashes
Light source
intensity
Indicator
Light source
LED indicator
On your Bluetooth device, go to the
Bluetooth menu and remove Philips
TAA6219 from the device list.
Turn off the Bluetooth function of
your Bluetooth device.
Press both volume+ and volume- on
the headphones for 4 seconds at the
same time.
Follow steps in “Use your
headphones- Pair the headphones
with your Bluetooth device for the
�rst time.”
Pair the headphones with your
Bluetooth device, select Philips
TAA6219.
EN 11
6 Technical data
Speci�cations are subject to change without
notice.
• Music time: 80 hours
• Talk time: 60 hours
• Standby time: 600 hours
• Charging time: 2.5 hours
• Rechargeable lithium polymer
battery (650 mAh)
• Bluetooth version: 5.4
• Compatible Bluetooth pro�les:
- HFP (Hands-Free Pro�le)
- A2DP (Advanced Audio
Distribution Pro�le)
- AVRCP (Audio Video Remote
Control Pro�le)
• Supported audio codec: SBC, AAC
• Frequency range: 2.402-2.480 GHz
• Transmitter power: < 10 dBm
• Operating range: Up to 10 meters
(33 feet)
• 1 AI mic
• Auto power off
• Low battery warning: available
• Built-in solar cell
• Solar panel charging 1 hour play
time:
≈2 hours
Illumination >100000 Lux
Cloudy day charge time
between 10:00am-16:00pm
• Removeable and washable cooling
gel earpads
Note
5 Reset the
headphones
1
2
3
4
5
If you encounter any pairing or connection
issue, you can follow the following
procedure to reset your headphones to
factory default settings.
04" 04"
12 EN
Compliance with EMF
This product complies with all
applicable standards and regulations
regarding exposure to electromagnetic
�elds.
Remove the integrated
battery
If there is no collection/recycling system
for electronic products in your country,
you can protect the environment by
removing and recycling the battery
before disposing of the headphones.
• Make sure the headphones are
disconnected before removing the
battery.
7 Notice
Declaration of conformity
Disposal of your old
product and battery
Your product is designed and manufactured
with high quality materials and components
which can be recycled and reused.
This symbol on a product means that the
product is covered by European Directive
2012/19/EU.
This symbol means that the product
contains batteries covered by European
Regulation (EU) 2023/1542 which cannot be
disposed of with normal household waste.
Inform yourself about the local separate
collection system for electrical and electronic
products and batteries. Follow local rules
and never dispose of the product and
batteries with normal household waste.
Correct disposal of old products and
batteries helps prevent negative
consequences for the environment and
human health.
Hereby, TP Vision Europe B.V. declares that
the product is in compliance with the
essential requirements and other relevant
provisions of RED Directive 2014/53/EU and
UK Radio Equipment Regulations SI 2017
No 1206. You can �nd the Declaration of
Conformity on www.philips.com/support.
EN 13
Environmental information
All unnecessary packaging has been
omitted.
Your system consists of materials which
can be recycled and reused if
disassembled by a specialized company.
Please observe the local regulations
regarding the disposal of packaging
materials, exhausted batteries and old
equipment.
Notice of compliance
The device complies with the FCC rules,
Part 15. Operation is subject to the
following two conditions:
1. This device may not cause harmful
interference, and
2. This device must accept any
interference received, including
interference that may cause
undesired operation.
FCC rules
This equipment has been tested and
found to comply with the limits for a Class
B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed
to provide reasonable
protection against harmful interference
in a residential installation. This
equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the
following measures:
Reorient or relocate the receiving
antenna
Increase the separation between
equipment and receiver
Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected
Consult the dealer or an experienced
radio/TV technician for help
FCC Radiation Exposure Statement:
This equipment complies with FCC
radiation exposure limits set forth for an
uncontrolled environment.
This transmitter must not be co-located or
operated in conjunction with any other
antenna or transmitter.
Caution:
The user is cautioned that
changes or modi�cations not expressly
approved by the party responsible for
compliance could void the user's authority
to operate the equipment.
Canada:
This device contains licence-exempt
transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence- exempt
RSS(s). Operation is subject to the
following two conditions: (1) this device
may not cause harmful interference, and
(2) This device must accept any
interference received, including
interference that may cause undesired
operation of the device.
CAN ICES-(B)/NMB-(B)
IC Radiation Exposure Statement:
This equipment complies with Canada
radiation exposure limits set forth for
uncontrolled environments.
This transmitter must not be co-located
or operating in conjunction with any
other antenna or transmitter.
14 EN
Avis de conformité
Cet appareil satisfait aux règlements de
la FCC partie 15 du Code of Federal
Regulations. Son fonctionnement est
assujetti aux deux conditions suivantes :
1. Cet appareil ne doit pas causer
d’interférence préjudiciable et
2. l’appareil doit accepter toute
interférence reçue, y compris les
interférences qui peuvent causer un
fonctionnement non désiré.
Règlement de la FCC
Cet équipement a été testé et jugé
compatible avec les limites s’appliquant
aux appareils numériques de la classe B,
conformément à l’article 15 du
règlement de la FCC. Ces limites ont été
dé�nies pour fournir une protection
raisonnable contre les interférences
nuisibles dans le cadre d’une installation
résidentielle. Cet équipement génère,
utilise et peut émettre de l’énergie
radiofréquence et, s’il n’est pas installé ni
utilisé conformément aux instructions,
peut causer des interférences gênantes
pour les communications radio.
Rien ne garantit toutefois que des
interférences ne surviendront pas dans
une installation particulière. Si cet
équipement cause des interférences
nuisibles pour la réception de la radio ou
de la télévision, ce qui peut être
déterminé en mettant l’équipement hors
tension puis sous tension, l’utilisateur
devra essayer de corriger ces
interférences en effectuant une ou
plusieurs des opérations suivantes :
• Déplacez l’antenne de réception.
• Augmentez la distance entre
l’équipement et le récepteur.
• Branchez l’équipement à une prise
d’un circuit autre que celui sur lequel
le récepteur est branché.
• Consultez le détaillant ou un
technicien de radiotélévision
expérimenté.
Canada :
Le présent appareil est conforme aux
CNR d’Industrie Canada applicables aux
appareils radio exempts de licence.
L’exploitation est autorisée aux deux
conditions suivantes : (1) l’appareil ne
doit pas produire de brouillage, et (2)
l’utilisateur de l’appareil doit accepter
tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en
compromettre le fonctionnement.
CAN ICES-(B)/NMB-(B)
Déclaration d’IC sur l’exposition aux
radiations:
Cet équipement est conforme aux limites
d’exposition aux radiations dé�nies par le
Canada pour des environnements non
contrôlés.
Cet émetteur ne doit pas être installé au
même endroit ni utilisé avec une autre
antenne ou un autre émetteur.
9 Frequently
asked
questions
My On-ear solar-powered headphones
do not turn on.
The battery level is low. Charge the
headphones.
I cannot pair my On-ear solar-powered
headphones with my Bluetooth device.
The Bluetooth is disabled. Enable the
Bluetooth feature on your Bluetooth
device and turn on the Bluetooth device
before you turn on the headphones.
The Bluetooth device cannot �nd the
headphones.
• The headphones may be connected
to a previously paired device. Turn
off the connected device or move it
out of range.
• Pairing may have been reset or the
headphones have been previously
paired with another device. Pair the
headphones with the Bluetooth
device again as described in the user
manual. (see ‘Pair the headphones
with your Bluetooth device for the
�rst time’ on page 7).
My On-ear solar-powered headphones
are connected to a Bluetooth
stereo-enabled mobile phone, but
music only plays on the mobile phone
speaker.
Refer to the user manual of your mobile
phone. Select to listen to music through
the headphones.
15 EN
8 Trademarks
The Bluetooth® word mark and logos are
registered trademarks owned by
Bluetooth SIG, Inc. and any use of such
marks by MMD Hong Kong Holding
Limited is under license. Other
trademarks and trade names are those of
their respective owners.
Bluetooth
Siri is a trademark of Apple Inc.,
registered in the U.S. and other countries.
Siri
Google and Google Play are trademarks
of Google LLC.
Google
The audio quality is poor and crackling
noise can be heard.
• The Bluetooth device is out of range.
Reduce the distance between your
headphones and Bluetooth device,
or remove obstacles between them.
• Charge your headphones.
The audio quality is poor when
streaming from a mobile phone, is very
slow or streaming does not work at all.
Make sure your mobile phone not only
supports (mono) HFP but also supports
A2DP and is BT4.0x (or higher)
compatible (see ‘Technical data’ on page
11).
I hear but cannot control music on my
Bluetooth device (e.g. play/pause/skip
forward/backward).
Make sure the Bluetooth audio source
supports AVRCP (see ‘Technical data’ on
page 11).
The volume level of the headphones is
too low.
Some Bluetooth devices cannot link the
volume level with the headphones
through volume sync. In this case, you
have to adjust the volume on your
Bluetooth device independently to
achieve an appropriate volume level.
I cannot connect the headphones to
another device, what do I do?
• Make sure the Bluetooth function of
the previous paired device is turned
off.
• Repeat the pairing procedure on
your second device (see ‘Pair the
headphones with your Bluetooth
device for the �rst time’ on page 7).
For further support,
visit www.philips.com/support
16 EN
Clean your headphones regularly.
• Use a clean, damp cloth to clean your
headphones - especially the sound
conduits and the microphone holes -
regularly and avoid buildup of
substances such as sweat or earwax.
• If any sweat or water droplets are left
in the sound conduits, air holes or
microphone holes, the sound level will
temporarily drop or cut out entirely.
This is not a malfunction. Use a soft,
damp cloth to dry the headphones
thoroughly. Alternatively, “for in-ear
headphones remove the earbud tips,
turn the sound conduits downward
and gently tap the headphones about
�ve times on a dry cloth or similar to
remove any water collected inside.
• Be sure the headphones are
completely dry before charging and
using. Avoid using disposable alcohol
pads or other substances for cleaning.
Charge your headphones regularly.
If the headset is not used for a long time,
the rechargeable battery will begin to
lose its charge. To avoid this loss, please
fully charge the battery at least once
every three months.
UM_TAA6219_00_EN_V1.0
MMD Hong Kong Holding Limited. All rights reserved. Speci�cations are subject to change without notice.
Philips and the Philips Shield Emblem are registered trademarks
of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility
of MMD Hong Kong Holding Limited or one of its affiliates, and
MMD Hong Kong Holding Limited is the warrantor in relation to this product. All other company and product names may be
trademarks of their respective companies with which they are associated.
