POLYCOOL AIRINDPLYA55K 4.5kW Portable Industrial Spot Cooler User Manual

Model shown is PN-350

User Manual

[Revision 7.0]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE AND MAY

VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by this manual may vary in appearance,

assembly, inclusions, specifications, description, and packaging.

PN-350, PN-550, PN-750 Industrial Spot Coolers

E&OE © Polycool 2

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death, injury or

equipment or property damage if not understood or followed. Safety messages have the following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be INJURED if you do

not follow instructions or equipment

damage may occur.

It is vital that you read and understand this

user manual before using the product,

including safety warnings, and any assembly

and operating instructions. Keep the manual

for future reference.

Safety precautions and recommendations

detailed here must be fully understood and

followed to reduce the risk of injury, fire,

explosion, electrical hazard, and/or property

damage.

Safety information presented here is generic

in nature – some advice may not be

applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery powered or

combustion engine powered.

• Before Use - If you are not familiar with the

safe operation/handling of the equipment or

are in any way unsure of any aspect of

suitability or correct use for your

application, you should complete training

conducted by a person or organization

qualified in safe use and operation of this

equipment, including fuel/electrical handling

and safety.

• Do NOT operate the equipment in

flammable or explosive environments, such

as in the presence of flammable liquids,

gases, or dust. The equipment may create

sparks or heat that may ignite flammable

substances.

• Keep clear of moving parts.

• Equipment may be a potential source of

electric shock or injury if misused.

• Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

• Do NOT allow others to use the equipment

unless they have read this manual and are

adequately trained.

• Keep packaging away from children - risk

of suffocation! Operators must use the

equipment correctly. When using the

equipment, consider conditions and pay

due care to persons and property.

General Work Area Safety

•

Work areas should be clean and well it.

• Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

• If devices are provided for connecting dust

extraction / collection facilities, ensure

these are connected and used properly.

Dust collection can reduce dust-related

hazards.

General Personal Safety

•

Wear appropriate protective equipment

when operating, servicing, or when in the

operating area of the equipment to help

protect from eye and ear injury, poisoning,

burns, cutting and crush injuries. Protective

equipment such as safety goggles,

respirators, non-slip safety footwear, hard

hat, hearing protection etc should be used

for appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective equipment.

Do not wear loose clothing or jewellery,

which can be caught in moving parts. Keep

hair and clothing away from the equipment.

• Stay alert and use common sense when

operating the equipment. Do not over-

reach. Always maintain secure footing and

balance.

• Do not use the equipment if tired or under

the influence of drugs, alcohol, or

medication.

• This equipment is not intended for use by

persons with reduced physical, sensory, or

mental capabilities.

General Fuel Safety

•

Petrol/fuel/gasoline is extremely flammable

– keep clear of naked flames or other

ignition sources.

• Do not spill fuel. If you spill fuel, wipe it off

the equipment immediately – if fuel gets on

your clothing, change clothing.

• Do NOT smoke near fuel or when

refuelling.

• Always shut off the engine before

refuelling.

• Do NOT refuel a hot engine.

• Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly.

• Always refuel in well ventilated areas.

• Always check for fuel leakage. If fuel

leakage is found, do not start, or run the

engine until all leaks are fixed.

General Carbon-Monoxide Safety

•

Using a combustion engine indoors CAN

KILL IN MINUTES. Engine exhaust

contains carbon-monoxide – a poison you

cannot smell or see.

• Use combustion engines OUTSIDE only,

and far away from windows, doors, and

vents.

General Equipment Use and Care

•

The equipment is designed for domestic

use only.

• Handle the equipment safely and carefully.

• Before use, inspect the equipment for

misalignment or binding of moving parts,

loose components, damage, or any other

condition that may affect its operation. If

damaged, have the equipment repaired by

an authorised service centre or technician

before use.

• Prevent unintentional starting of the

equipment - ensure equipment and power

switches are in the OFF position before

connecting or moving equipment. Do not

carry equipment with hands or fingers

touching any controls. Remove any tools or

other items that are not a part of the

equipment from it before starting or

switching on.

• Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be safer

when used within its design and usage

parameters.

• Use the equipment and accessories etc. in

accordance with these instructions,

considering working conditions and the

work to be performed. Using the equipment

for operations different from those intended

could result in hazardous situations.

• Always keep equipment components

(engines, hoses, handles, controls, frames,

housings, guards etc) and accessories

(cutting tools, nozzles, bits etc) properly

maintained. Keep the equipment clean and,

where applicable, properly lubricated.

• Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the equipment

near flammable materials, combustible

gases, or liquids etc.

• The equipment is not weather-proof, and

should not be stored in direct sunlight, at

high ambient temperatures or locations that

are damp or humid.

• Do not clean equipment with solvents,

flammable liquids, or harsh abrasives.

• For specific equipment safety use and care,

see Equipment Safety.

POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

PN-350, PN-550, PN-750 Industrial Spot Coolers

E&OE © Polycool 3

General Electrical Safety

•

Inspect electrical equipment, extension

cords, power bars, and electrical fittings for

damage or wear before each use. Repair or

replace damaged equipment immediately.

• Ensure all power sources conform to

equipment voltage requirements and are

disconnected before connecting or

disconnecting equipment.

• When wiring electrically powered

equipment, follow all electrical and safety

codes.

• Always use a Residual Current Device

(RCD) (GFCI) / Earth Leakage Circuit

Breaker / Safety Switch when operating this

item (electrical items only).

• High voltage / high current power lines may

be present. Use extreme caution to avoid

contact or interference with power lines.

Electrical shock can be fatal.

General Electrical Safety

•

Electrically grounded equipment must have

an approved cord and plug and be

connected to a grounded electrical outlet.

• Do NOT bypass the ON/OFF switch and

operate equipment by connecting and

disconnecting the electrical cord.

• Do NOT use equipment that has exposed

wiring, damaged switches, covers or

guards.

• Do NOT use electrical equipment in wet

conditions or in damp locations.

• Do NOT use electrical cords to lift, move or

carry equipment.

• Do NOT coil or knot electrical cords, and

ensure electrical cords are not trip hazards.

General Service Information

•

The equipment must be serviced or

repaired at authorised service centres by

qualified personnel only.

• Replacement parts must be original

equipment manufacturer (OEM) to ensure

equipment safety is maintained.

• Do NOT attempt any maintenance or repair

work not described in this manual.

• After use, the equipment and components

may still be hot – allow the equipment to

cool and disconnect spark plugs and/or

electrical power sources and/or batteries

from it before adjusting, changing

accessories, or performing repair or

maintenance.

• Do NOT adjust while the equipment is

running.

• Perform service-related activities in suitable

conditions, such as a workshop.

• Replace worn, damaged or missing

warning/safety labels immediately.

Industrial Spot Cooler Safety

•

If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory, or mental capabilities or lack

of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the

hazards involved.

• Children should not play with the appliance.

• Cleaning and user maintenance should not be made by children without supervision.

• This appliance is intended to be used by expert or trained users in shops, in light industry and on farms, or for commercial use by lay persons.

• Disconnect the appliance from its power source during service and when replacing parts.

• Please do not use air cooler in places that use or store volatile substances (diluents, gasoline, kerosene, liquefied gas and other volatile liquids;

magnesium, aluminium, lead and other volatile dusts and vapours) to avoid possible ignition, explosion, fire and burn injuries.

• Please do not remould for use, which may lead to machine breakdown or even fire, etc.

• Except for professional maintenance personnel, other personnel are not allowed to assemble or disassemble to avoid fire, electrocution, injury,

and other safety accidents. If repair is needed, please contact an authorised service centre.

• Do not use it in places with rain, snow, and/or water. Do not operate with wet hands.

• Use a 220-240V/50Hz power supply. Otherwise, there might be a machine breakdown or safety accident.

• Use a separate 20A rated current socket. Use of socket with other electrical appliances may cause error.

• Assign professionals to operate according to equipment standard and wiring upon installation. Otherwise, there may be safety accident.

• Do not go near fire sources to avoid damaging the machine.

• Equip safe and reliable ground lead and use leakage protector.

• Use it in specified range of 18 - 45°C, otherwise there may be a machine breakdown.

• Do not move the air cooler when the machine is running. Ensure to set the castor brake to locked status.

• Please immediately stop using it in case of error (stopped rotation, strange noise, improper vibration, and unusual odour).

• To prevent disaster and damage, air cooler cannot be used in the following places:

• Vibrating floor

• Gradient floor

• Stairway, emergency exit and house exit and entrance, etc.

• Places with unstable articles piled around

• Windy and moist places or places with floating metallic powder

• Grip the plug when pulling it off instead of pulling on the power line directly. Otherwise, it may damage the plug, or cause sparks or safety

accidents.

• Pull the power plug off the socket if the machine is not used for an extended period.

• To prevent electrocution, please pull the power plug off the socket upon installation and maintenance.

• Please use a dry, clean cloth to wipe away any dirt/dust on the power plug. Dusty or moist plug can cause poor contact or electric leakage,

leading to safety accidents.

• Do not haphazardly bend, drag, twist, pinch or change the power line. Do not overload the power line. Otherwise, it could start a fire, cause

electrocutions and other accidents.

• Please do not use it on boats, vehicles, etc. Otherwise, there could be safety accidents.

• Please do not stick fingers or hands in the vent.

POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

PN-350, PN-550, PN-750 Industrial Spot Coolers

E&OE © Polycool 4

Safety Symbols

The product may have safety warning labels attached to it, explained below. Understand the symbols on your

product and their meanings. If any stickers become unreadable, unattached etc., replace them.

Flammable Material Hazard

Flammable liquids, gases, or

substances etc may present.

Avoid ignition sources and open

flames. Danger of fire.

Read User Manual

Read and fully understand

product safety warnings,

operation, procedures etc before

using the product.

Use Hand Protection

Wear appropriate hand protection

and take due care as the product

or use of the product may present

hand hazards.

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Electrocution / Electrical Shock

Hazard

High voltage or high current

electricity may be present or

required by the product. Take

due care when handling electrical

products, cables, plugs and

leads. Electrical shock can be

fatal.

Toxic Fumes / Dust Hazard

Using the product or by-products

from use may produce fumes,

smoke or particles that could be

harmful if inhaled. Wear

appropriate breathing protection

and have adequate ventilation.

Explosive Material Hazard

Combustible liquids, gases, or

substances etc may be present.

Avoid ignition sources and open

flames. Danger of explosion.

Cutting / Amputation Hazard

The product may have blades,

edges or mechanical devices that

can cause severe cut injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Crush Hazard

The product may have blades,

edges or mechanical devices that

can cause severe crush injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Single Operator Only

The product must be operated by

a single person only. More than

one person operating the product

may introduce additional hazards.

Use Face Protection

Wear appropriate full-face

protection and take due care as

the product or use of the product

may present face and eye

hazards.

Use Foot Protection

Wear appropriate foot protection

and take due care as the product

or use of the product may present

foot hazards.

Use Eye / Ear / Head Protection

Wear appropriate eye and / or

ear and / or head protection and

take due care as the product or

use of the product may present

eye, hearing, and head hazards.

Running Hazard

Do not run on or near the product

as doing so may present a fall

hazard.

Diving Hazard

Do not dive into the product as

doing so may present a neck /

head injury hazard.

Adult Supervision Required

Always supervise children and

other users of a product to

prevent drowning or injury.

Skin Penetration / Puncture

Hazard

The product may produce

pressure, emit liquids or objects

that can cause severe injury to

fingers, limbs, blood etc. Take

due care when handling and

using the product.

Hot Surface Hazard

Be aware that the product may

produce high temperatures and

hot surfaces that can cause burn

injuries.

Flying Debris Hazard

Be aware that the product or use

of the product may present

hazards produced by flying

debris. Wear appropriate clothing

and protective devices.

Moving Parts Hazard

Be aware that the product

contains or uses mechanical

devices that move or rotate.

Always wait for moving parts to

stop fully before handling the

product, adjusting, maintenance

etc.

POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

PN-350, PN-550, PN-750 Industrial Spot Coolers

E&OE © Polycool 5

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Pull Hazard

Be aware that the product

contains or uses mechanical

devices that can pull in objects

and can cause severe injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Slope / Fall Injury Hazard

Be aware that using the product

on sloping surfaces or in slippery

conditions may present additional

dangers from falls and contact

with blades, moving parts, hot

surfaces etc.

"Slam Dunk" Warning

Do NOT attempt "slam dunk"

manoeuvres as this may result in

severe injury due to falling,

product breakage or collapse etc.

Electrocution / Electrical Shock

Hazard - Outdoor

High voltage or high current

electricity may be present or

required by the product. Do NOT

use in rain, damp, or wet

conditions. Electrical shock can

be fatal.

Electrocution / Electrical Shock

Hazard - Disconnect

High voltage or high current

electricity may be present or

required by the product. Always

disconnect the product from the

electrical supply before handling

the product, adjusting,

maintenance etc.

Power Line Electrocution

Hazard

High voltage / high current power

lines may be present. Use

extreme caution to avoid contact

or interference with power lines.

Electrical shock can be fatal.

"Kick-Back" Hazard

High level of "kick-back" hazard

that can cause the machine to

suddenly rotate towards operator.

Kick-back injury can be fatal.

Winch Operator Position

Hazard

Do NOT stand between winch

and load. Do NOT use winch to

move people.

Winch Lift Hazard

Do NOT LIFT load vertically. Use

machine to PULL only.

Cable Hazard

Ensure that load bearing cable is

not kinked or knotted.

Winch Cable Hazard

Ensure that there is a minimum

number of cable coils on

winching mechanism.

Winch Hook Hazard

Carry hook to load – do NOT

throw or run.

Flash / Blinding Hazard

Wear appropriate eye protection

for welding. Direct exposure to

weld arcs may cause permanent

eye injury.

Laser Hazard

Laser may be in use – do NOT

look directly at laser or allow

others to.

POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

PN-350, PN-550, PN-750 Industrial Spot Coolers

E&OE © Polycool 6

Table of Contents

Safety ............................................................................................................................................................. 2

Safety Symbols ........................................................................................................................................................... 4

Parts Identification ....................................................................................................................................... 7

Spare Parts .................................................................................................................................................... 8

Installation ..................................................................................................................................................... 9

Installing the Connector .............................................................................................................................................. 9

Installing the Cold Exhaust Pipe ................................................................................................................................. 9

Cutting the Extension Pipe ....................................................................................................................................... 10

Reducing the Diameter of the Extension Pipe .......................................................................................................... 10

Connecting the Extension Pipe ................................................................................................................................ 10

Operation ..................................................................................................................................................... 11

Selecting Fan Strength ............................................................................................................................................. 11

Compressor Overheat and Overload Protection ...................................................................................................... 11

Adjustment Range of Exhaust Pipes ........................................................................................................................ 11

Water Tank Operation .............................................................................................................................................. 12

Drainpipe (optional) .................................................................................................................................................. 12

Requirements for Operation Site .............................................................................................................................. 12

Maintenance ................................................................................................................................................ 13

Troubleshooting ......................................................................................................................................... 14

Specifications ............................................................................................................................................. 15

PN-350 ...................................................................................................................................................................... 15

PN-550 ...................................................................................................................................................................... 15

PN-750 ...................................................................................................................................................................... 16

POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

PN-350, PN-550, PN-750 Industrial Spot Coolers

E&OE © Polycool 7

Parts Identification

Note: Model shown is PN-350

No. Name

1 Cold exhaust pipe

2

Switch Box

3 F

ilter screen

4

Front shell

5

Hot exhaust pipe

6 Handle

7

Right plate

8

Water tank

9 Castor wheels

1

6

4

3

2

5

7

8

9

POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

PN-350, PN-550, PN-750 Industrial Spot Coolers

E&OE © Polycool 8

Spare Parts

Spare parts available for purchase, scan QR code/s below:

QR Code SKU

AIRINDPLYA35K

AIRINDPLYA55K

AIRINDPLYA75K

POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

PN-350, PN-550, PN-750 Industrial Spot Coolers

E&OE © Polycool 9

Installation

Installing the Connector

Direct the turning of the connector to the dent of the detachable elbow base on the machine. Insert and rotate it

anti-clockwise. The elbow is in place when a clicking sound is heard.

Installing the Cold Exhaust Pipe

Align the turning of the cold exhaust pipe to the dent of the cold exhaust pipe, insert and rotate it to the left to

secure it in place.

POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

PN-350, PN-550, PN-750 Industrial Spot Coolers

E&OE © Polycool 10

Cutting the Extension Pipe

1. Cut the extension pipe based on the required length needed.

2. As shown in the figure below, separate the exhaust pipe from the groove with a flathead screwdriver or other

sharp tools at the location where it is supposed to be cut, and cut it off with pliers or scissors.

Reducing the Diameter of the Extension Pipe

Rotate the pipe in a clockwise direction to reduce the diameter of the pipe opening.

Connecting the Extension Pipe

1. Detach the joint of the hot exhaust pipe and cover the extension pipe outside the hot exhaust pipe.

2. Screw the end tight and ensure it is secure. Use a strong adhesive tape to secure it, if necessary.

3. Use binders to secure the attached pipe opening of the extended hot exhaust pipe.

POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

PN-350, PN-550, PN-750 Industrial Spot Coolers

E&OE © Polycool 11

Operation

Selecting Fan Strength

•

Rotate the selecting switch on the cover of the machine to or and the compressor immediately

launches into refrigeration. In the meantime, start the draught fan to blow air out. The blast capacity has or

for customer to choose from.

•

When the switch is rotated to “0”, the machine is turned OFF and stops running.

ATTENTION! Turn the selecting switch OFF and cut the power off before moving the machine. When

the machine is off, it may be restarted after 3 minutes.

Compressor Overheat and Overload Protection

•

Overly high or low voltage and overly high ambient temperature can cause the compressor to overheat and

overload. To protect the compressor, the overload protector will be activated to cut the power of the

compressor OFF.

ATTENTION! When the overload protector is activated, the machine only blows out natural air but does

not cool it. If the overload protector is activated frequently, please find out and eliminate the cause

before using the machine.

Adjustment Range of Exhaust Pipes

•

Cold air pipe may rotate left or right to 360° (hot air pipe is installed).

•

Cold air pipe may be moved up or town to 150°.

•

The range of adjustment angle for hot air pipe is 45°.

ATTENTION! Adjust the cold exhaust pipe in advance and use the air-out direction of the hot exhaust

pipe later. When adjusting the air-out angle of the cold exhaust pipe, please grip the connector to do

adjustments and do not hold the cold exhaust pipe directly.

POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

PN-350, PN-550, PN-750 Industrial Spot Coolers

Water Tank Operation

When the water in the tank and the water level indicator are parallel with each other, set the gear to 0, pour the

water out and re-install the water tank. Choose a gear to make it work properly.

ATTENTION! Please do not move the machine when the water is full. Pour the water before moving it.

Drainpipe (optional)

Condensate water may be discharged with a drainpipe (not included in some units). Take the water tank out and

install the drainpipe directly on the drainage of the tank to cross the round hole on the corresponding side plate.

Requirements for Operation Site

•

When the machine is running, both the filter screen and the cold air pipe should be 30cm or more from walls

or other obstacles. The hot exhaust pipe should be 80cm or more from walls, ceilings, or other obstacles.

•

The machine must be placed on a flat, stable ground. To avoid accidents, do not place it on slopes, rugged

terrains, entrances or exits, etc.

•

To avoid accidents, do not use it in the rain, snow, and other wet/humid environment.

ATTENTION! Do not place obstacles in front of the filter screen or air outlet of the cold air pipe and the

hot exhaust pipe. Please do not direct hot air from the hot exhaust pipe towards flammable objects.

POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

PN-350, PN-550, PN-750 Industrial Spot Coolers

Maintenance

•

Clean the filter screen regularly. Dust and dirt on the filter screen may affect the air supply and cause

frosting of the heat exchanger, leading to a possible machine breakdown.

•

For filter screen cleaning, carefully remove it from the unit and use a vacuum cleaner to suck dust out of the

filter screen and then use clean water to wash it. Re-install it when it is completely dry.

ATTENTION! When cleaning machine surfaces, please do not use diluents, volatile oils, and other

cleaning agents that may damage surfaces.

•

Check if the power line is broken. If so, have it replaced immediately.

•

Check if any screws are loose. If so, re-screw them tightly.

•

Before long-term storage of the machine or when it will not be used for an extended period, pour out the

water in the water tank and re-install it when the tank is dry.

•

Do not place or store the machine horizontally or upside down.

•

Store the machine where kids cannot reach or access it. Avoid storing it in places with high ambient

temperatures, rain exposure or direct sunlight.

ATTENTION! Pull out the power plug when changing parts during maintenance and checks. Pull the

power plug out when storing the machine.

POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

PN-350, PN-550, PN-750 Industrial Spot Coolers

Troubleshooting

If the spot cooler breaks down, please cut the power off immediately and pull the power plug out from the socket

to check the following.

Fault Possible Cause Possible Solution

Unit does not

operate

Power plug is loose or fell off Please insert the power plug firmly in the power socket

Burnt fuse

Ask a professional technician or service centre to

replace the fuse

Unit does not blow

cold air

Heat exchanger surface is blocked

with debris

Clean heat exchanger surface to ventilate it and to

release excess heat

Hot exhaust blower failure Repair or replace hot exhaust blower

External temperature is too high

Please use it in a proper place with proper spacing

requirements

Compressor capacitor is damaged Replace compressor capacitor

Refrigerating system pipeline is

clogged

Replace pipeline system or remove the obstacle

Overly high or low input voltage Please select the proper voltage

Overheated compressor and

overload protection fails

Restart after cooling

Failed compressor motor Repair or replace compressor

Water Leakage

Drainpipe opening is clogged clear the drainpipe

Water tank position is placed

improperly

Reset it

Filter screen has dust and filth Please clean filter screen

Water tank is full Pour water out of the water tank

POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

PN-350, PN-550, PN-750 Industrial Spot Coolers

Specifications

PN-350

Air Volume 400m³/h

Rated Voltage 220 - 240V/50Hz

Power Plug 10A Australian Standard

Refrigerating Capacity 9200 Btu (2.7kW)

Operating Temperature 18-45°C

Refrigerant R32 / 400g

Noise Level 55dB

Condensation Tank 5L

Power Cord Length 1.9m

Extended duct length 1.2m

Note: Minimal Assembly required

PN-550

Air Volume 800m³/h

Rated Voltage 220-240V/50Hz

Power Plug 15A

Refrigerating capacity 15,300 BTU (4.5kW)

Operating Temperature 18-45°C

Refrigerant R32 / 840g

Noise Level 60dB

Condensation tank 8L

Power cord length 1.9m

Extended duct length 1.2m

Note: Minimal Assembly required

POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

PN-350, PN-550, PN-750 Industrial Spot Coolers

PN-750

Air Volume 1200m³/h

Rated Voltage 220-240V/50Hz

Power Plug 15A

Refrigerating Capacity 22,200 BTU (6.5kW)

Operating Temperature 18-45°C

Refrigerant R32 / 1220g

Noise Level 65dB

Condensation Tank 13L

Power Cord Length 1.9m

Extended duct length 1.2m

Note: Minimal Assembly required

POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

Some experts believe that the incorrect or prolonged use of almost any

product may cause serious injury or death. To help reduce your risk of

serious injury or death, refer to the information below. For more information,

see www.datastreamserver.com/safety



Consult all documentation, packaging,

and product labelling before use. Note

that some products feature

documentation available online. It is

recommended to print and retain the

documentation.



Before each use, check the product for

loose/broken/damaged/missing parts,

wear, or leaks (if applicable). Never use a

product with

loose/broken/damaged/missing parts,

wear, or leaks.



Products must be inspected and serviced

(if applicable) by a qualified technician

every 6 months. This is based on

average residential use by persons of

average size and strength, and on a

property of average metropolitan size.

Use beyond these recommendations may

require more frequent

inspections/servicing.



Ensure that all users of the product have

completed a suitable industry recognised

training course before being allowed

access to the product.



The product has been supplied by a general merchandise

retailer that may not be familiar with your specific

application or description of application. Be sure to attain

third-party approval from a qualified specialist for your

application before use, regardless of any assurances from

the retailer or its representatives.



This product is not intended for use where fail-safe

operation is required. As with any product (for example,

automobile, computer, toaster), there is the possibility of

technical issues that may require the repair or

replacement of parts, or the product itself. If the possibility

of such failure and the associated time it may take to

rectify could in any way inconvenience the user, business,

or employee, or financially affect the user, business, or

employee, then the product is not suitable for your

requirements. This product is not intended for use where

incorrect operation or a failure of any kind, including but

not limited to, a condition requiring product return,

replacement, parts replacement, or service by a

technician may cause financial loss, loss of employee

time or an inconvenience requiring compensation.



If this product has been purchased in error when

considering the information presented here, contact the

retailer directly for details of their returns policy, if

required.

diagrams, or images may be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying, scanning, or recording, or any information storage and retrieval system,

without express permission or consent from the publisher.

POLYCOOL AIRINDPLYA55K 4.5kW Portable Industrial Spot Cooler

Product's Documents

Product manual

Specifications

POLYCOOL AIRINDPLYA55K Questions and Answers