Loading ...
Loading ...
Loading ...
4
OPERATION
WARNING
To reduce the risk of injury , always
remove battery pack before chang-
ing or removing accessories. Only use acces-
sories specically recommended for this tool.
Others may be hazardous.
Always wear proper eye protection marked to
comply with ANSI Z87.1.
When working in dusty situations, wear appro-
priate respiratory protection or use an OSHA
compliant dust extraction solution.
Fuel Gauge
To determine the amount of charge left in the bat-
tery, pull the trigger. The Fuel Gauge will light up for
2-3 seconds.
To signal the end of charge, 1 light on the fuel gauge
will ash for 2-3 seconds.
Selecting Drill or Drive Action
1. To use the drilling mode, rotate
the torque selector collar until the
drill symbol
appears in line
with the arrow.
2. To use the driving mode rotate
the torque selector collar until the
desired clutch setting appears in
line with the arrow.
The adjustable clutch, when prop-
erly adjusted, will slip at a preset
torque to prevent driving the screw
too deep into dierent materials and to prevent
damage to the screw or tool.
The torque specications shown here are approximate
values obtained with a fully charged battery pack.
TORQUE SPECIFICATIONS
Clutch
Setting
in. lbs Applications
1-5
6-10
11-16
8-15
16-21
22-32
Small screws in softwood.
Medium screws in softwood or small
screws in hardwood.
Large screws in softwoods. Medium
screws in hardwood or large screws in
hardwood with pilot hole.
NOTE: Because the settings shown in the table are
only a guide, use a piece of scrap material to test
the dierent clutch settings before driving screws
into the workpiece.
Selecting Speed
The speed selector is on top of the
motor housing. Allow the tool to
come to a complete stop before
changing speeds. See “Applica-
tions” for recommended speeds
under various conditions.
1. For Low speed, push the speed selector to display
“1”.
2. For High speed, push the speed selector to display
“2”.
Using the Control Button
The control button can be set to
three positions: forward, reverse and
lock. Always allow the motor to come
to a complete stop before using the
control button.
1. For forward (clockwise) rotation,
push in the control button to dis-
play Forward
►
. Check the direction of rotation
before use.
ASSEMBLY
WARNING
Recharge only with the charger
specied for the battery. For spe-
cic charging instructions, read the operator’s
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
WARNING
Always remove battery pack before
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
WARNING
Only use accessories specically
recommended for this tool. Others
may be hazardous.
Attaching and Removing Attachments
1. Remove the battery pack.
Spindle
Collar
2. Select the appropriate attach-
ment for the job.
3. Pull out the collar and snap the
attachment onto the spindle.
NOTE: The right angle and
offset attachments can be
installed 360° in 16 preset
detents.
4. When using the right angle
attachment, repeat the proce-
dure to attach another chuck, if desired.
5. To remove the attachment, pull out the collar and
remove the attachment.
Attaching and Removing Accessories
3/8" Keyless Chuck Attachment
Always remove the battery before inserting or remov-
ing bits. Select the proper style and size bit for the job.
This tool is equipped with a spindle lock. The chuck
can be tightened with one hand, creating higher grip
strengths on the bit.
1. To open the chuck jaws, turn the sleeve in the
counterclockwise direction.
When using drill bits, allow the bit to strike the
bottom of the chuck. Center the bit in the chuck
jaws and lift it about 1/16" off of the bottom.
When using screwdriver bits, insert the bit far
enough for the chuck jaws to grip the hex of the bit.
2. To close the chuck jaws, turn the sleeve in the
clockwise direction. The bit is secure when the
chuck makes a ratcheting sound and the sleeve
can not be rotated any further.
3. To remove the bit, turn the sleeve in the counter-
clockwise direction.
NOTE: A ratcheting sound may be heard when the
chuck is opened or closed. This noise is part of the
locking feature, and does not indicate a problem with
the chuck’s operation.
1/4" Hex Attachment
1. To attach an accessory, press the
shank into the hex drive chuck.
2. To remove the accessory, pull out
the ring and remove the accessory.
Release the ring.
Oset Attachment, Right Angle
Attachment, and 1/4" Hex Spindle
1. To attach an accessory, press the
shank into the attachment.
2. To remove the accessory, pull the shank from the
attachment.
Loading ...
Loading ...
Loading ...