BAUMR-AG DP15 600W 10" Pedestal Bench Drill Press User Manual

User Manual

[Revision 2.0 December 2023]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE AND MAY

VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by this manual may vary in appearance,

assembly, inclusions, specifications, description, and packaging.

DP15 Drill Press

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death, injury or

equipment or property damage if not understood or followed. Safety messages have the following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be INJURED if you do

not follow instructions or equipment

damage may occur.

It is vital that you read and understand this

user manual before using the product,

including safety warnings, and any assembly

and operating instructions. Keep the manual

for future reference.

Safety precautions and recommendations

detailed here must be fully understood and

followed to reduce the risk of injury, fire,

explosion, electrical hazard, and/or property

damage.

Safety information presented here is generic

in nature – some advice may not be

applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery powered or

combustion engine powered.

• Before Use - If you are not familiar with the

safe operation/handling of the equipment or

are in any way unsure of any aspect of

suitability or correct use for your

application, you should complete training

conducted by a person or organization

qualified in safe use and operation of this

equipment, including fuel/electrical handling

and safety.

• Do NOT operate the equipment in

flammable or explosive environments, such

as in the presence of flammable liquids,

gases, or dust. The equipment may create

sparks or heat that may ignite flammable

substances.

• Keep clear of moving parts.

• Equipment may be a potential source of

electric shock or injury if misused.

• Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

• Do NOT allow others to use the equipment

unless they have read this manual and are

adequately trained.

• Keep packaging away from children - risk

of suffocation! Operators must use the

equipment correctly. When using the

equipment, consider conditions and pay

due care to persons and property.

General Work Area Safety

•

Work areas should be clean and well it.

• Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

• If devices are provided for connecting dust

extraction / collection facilities, ensure

these are connected and used properly.

Dust collection can reduce dust-related

hazards.

General Personal Safety

•

Wear appropriate protective equipment

when operating, servicing, or when in the

operating area of the equipment to help

protect from eye and ear injury, poisoning,

burns, cutting and crush injuries. Protective

equipment such as safety goggles,

respirators, non-slip safety footwear, hard

hat, hearing protection etc should be used

for appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective equipment.

Do not wear loose clothing or jewellery,

which can be caught in moving parts. Keep

hair and clothing away from the equipment.

• Stay alert and use common sense when

operating the equipment. Do not over-

reach. Always maintain secure footing and

balance.

• Do not use the equipment if tired or under

the influence of drugs, alcohol, or

medication.

• This equipment is not intended for use by

persons with reduced physical, sensory, or

mental capabilities.

General Fuel Safety

•

Petrol/fuel/gasoline is extremely flammable

– keep clear of naked flames or other

ignition sources.

• Do not spill fuel. If you spill fuel, wipe it off

the equipment immediately – if fuel gets on

your clothing, change clothing.

• Do NOT smoke near fuel or when

refuelling.

• Always shut off the engine before

refuelling.

• Do NOT refuel a hot engine.

• Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly.

• Always refuel in well ventilated areas.

• Always check for fuel leakage. If fuel

leakage is found, do not start, or run the

engine until all leaks are fixed.

General Carbon-Monoxide Safety

•

Using a combustion engine indoors CAN

KILL IN MINUTES. Engine exhaust

contains carbon-monoxide – a poison you

cannot smell or see.

• Use combustion engines OUTSIDE only,

and far away from windows, doors, and

vents.

General Equipment Use and Care

•

The equipment is designed for domestic

use only.

• Handle the equipment safely and carefully.

• Before use, inspect the equipment for

misalignment or binding of moving parts,

loose components, damage, or any other

condition that may affect its operation. If

damaged, have the equipment repaired by

an authorised service centre or technician

before use.

• Prevent unintentional starting of the

equipment - ensure equipment and power

switches are in the OFF position before

connecting or moving equipment. Do not

carry equipment with hands or fingers

touching any controls. Remove any tools or

other items that are not a part of the

equipment from it before starting or

switching on.

• Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be safer

when used within its design and usage

parameters.

• Use the equipment and accessories etc. in

accordance with these instructions,

considering working conditions and the

work to be performed. Using the equipment

for operations different from those intended

could result in hazardous situations.

• Always keep equipment components

(engines, hoses, handles, controls, frames,

housings, guards etc) and accessories

(cutting tools, nozzles, bits etc) properly

maintained. Keep the equipment clean and,

where applicable, properly lubricated.

• Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the equipment

near flammable materials, combustible

gases, or liquids etc.

• The equipment is not weather-proof, and

should not be stored in direct sunlight, at

high ambient temperatures or locations that

are damp or humid.

• Do not clean equipment with solvents,

flammable liquids, or harsh abrasives.

• For specific equipment safety use and care,

see Equipment Safety.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

General Electrical Safety

•

Inspect electrical equipment, extension

cords, power bars, and electrical fittings for

damage or wear before each use. Repair or

replace damaged equipment immediately.

• Ensure all power sources conform to

equipment voltage requirements and are

disconnected before connecting or

disconnecting equipment.

• When wiring electrically powered

equipment, follow all electrical and safety

codes.

• Always use a Residual Current Device

(RCD) (GFCI) / Earth Leakage Circuit

Breaker / Safety Switch when operating this

item (electrical items only).

• High voltage / high current power lines may

be present. Use extreme caution to avoid

contact or interference with power lines.

Electrical shock can be fatal.

General Electrical Safety

•

Electrically grounded equipment must have

an approved cord and plug and be

connected to a grounded electrical outlet.

• Do NOT bypass the ON/OFF switch and

operate equipment by connecting and

disconnecting the electrical cord.

• Do NOT use equipment that has exposed

wiring, damaged switches, covers or

guards.

• Do NOT use electrical equipment in wet

conditions or in damp locations.

• Do NOT use electrical cords to lift, move or

carry equipment.

• Do NOT coil or knot electrical cords, and

ensure electrical cords are not trip hazards.

General Service Information

•

The equipment must be serviced or

repaired at authorised service centres by

qualified personnel only.

• Replacement parts must be original

equipment manufacturer (OEM) to ensure

equipment safety is maintained.

• Do NOT attempt any maintenance or repair

work not described in this manual.

• After use, the equipment and components

may still be hot – allow the equipment to

cool and disconnect spark plugs and/or

electrical power sources and/or batteries

from it before adjusting, changing

accessories, or performing repair or

maintenance.

• Do NOT adjust while the equipment is

running.

• Perform service-related activities in suitable

conditions, such as a workshop.

• Replace worn, damaged or missing

warning/safety labels immediately.

Application Conditions

This drill press is designed for operating under ambient temperatures between +5°C and 40°C and for installation at altitudes no more than 1000m

abov

e M.S.L. The surrounding humidity should less than 50% at 40°C. It can be stored or transported under ambient temperatures between -25°C

and 55°C.

Recycling and Disposal

This marking indicates that this product should not be disposed with other household wastes. To prevent possible harm to the environment

or

human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return

your used device, please use the return and collection systems or check with your local authority or local stores for advice of environmentally

safe recycling.

Understand your Machine

•

Read this manual and labels affixed to the machine to understand its limitations and potential hazards.

• Be thoroughly familiar with the controls and their proper operation. Know how to stop the machine and disengage the controls quickly.

• Do not attempt to operate the machine until you fully understand how to properly operate and maintain the engine and how to avoid accidental

injuries and/or property damage.

• If the unit is to be used by someone other than original purchaser or loaned, rented, or sold, always provide this manual and any needed safety

training before operation. The user can prevent and is responsible for accidents or injuries that may occur to themselves, other people, and

property.

• Do not force the machine. Use the correct machine for your application. The correct machine will do the job more efficiently and safer at the rate it

was designed.

Personal Safety

•

Do not permit children to operate this machine at any time.

• Keep children, pets, and other people not using the unit away from the work area. Be alert and shut off unit if anyone enters work area. Keep

children under the watchful care of a responsible adult.

• Do not operate the machine while under the influence of drugs, alcohol, or any medication that could affect your ability to use it properly.

• Dress properly. Wear heavy long pants, boots, and gloves. Do not wear loose clothing, short pants, or jewellery of any kind. Secure long hair so it

is above shoulder level. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewellery, or long hair can be caught in

moving parts.

• Protect eyes, face, and head from objects that may be thrown from the unit. Always wear safety goggles or safety glasses with side shields when

operating.

• Wear appropriate hearing protection. Wear respiratory protection to avoid the risk of inhaling harmful dust.

• Always keep hands and feet away from all moving parts during operation. Moving parts can cut or crush body parts.

• Always keep hands and feet away from all pinch points.

• Do not touch parts that might be hot from operation. Allow parts to cool before attempting to maintain, adjust, or service.

• Stay alert, watch what you are doing, and use common sense when operating the machine.

• Do not overreach. Do not operate the machine while barefoot or when wearing sandals or similar lightweight footwear. Wear protective footwear

that will protect your feet and improve your footing on slippery surfaces. Keep proper footing and balance at all times. This enables better control

of the machine in unexpected situations.

Inspect your Machine

•

Check your machine before starting it. Keep guards in place and in working order. Make sure all nuts, bolts, etc., are securely tightened.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

• Never operate the machine when it needs repair or is in poor mechanical condition. Replace damaged, missing, or failed parts before using it.

Keep the machine in safe working condition. Regularly check to see that the keys and adjusting wrenches are removed from the machine area

before starting it. A wrench or a key that is left attached to a rotating part of the machine may result in personal injury. Avoid accidental starting.

Be sure the motor switch is off before transporting the machine or performing any maintenance or service on the unit.

• Transporting or performing maintenance or service on a machine with its switch on invites accidents. If the machine should start to vibrate

abnormally, stop the motor, and check immediately for the cause. Vibration is generally a warning sign of trouble.

Electric Safety

•

Protect yourself from electric shock. Do not plug or unplug the motor while standing in or around damp or wet ground. Do not use the unit in wet

or damp areas or expose it to rain. Prevent body contact with grounded surfaces: pipes, radiators, ranges, and refrigerator enclosures. Make sure

your fingers do not touch the plug’s metal prongs when plugging or unplugging the unit.

• Avoid inadvertent starting. Make sure that the switch is switched off when plugging the plug into an outlet.

• Only use approved and appropriately identified extension cables for use outdoors. Only use cable reels in the unrolled state.

• Do not use the cable for purposes for which it is not intended. Do not use the cable to pull the plug out of the outlet. Protect the cable from heat,

oil, and sharp edges.

• Have your electric tool repaired by a qualified electrician. This electric tool conforms to the applicable safety regulations. Repairs may only be

performed by an electrician using original spare parts. Otherwise, accidents can occur.

Work Area & Store Area

•

Keep the work area orderly. Disorder in the work area can lead to accidents.

• Take environmental influences into account. Do not expose electric tools to rain. Do not use electric tools in a damp or wet environment. Make

sure that the work area is well-illuminated. Do not use electric tools where there is a risk of fire or explosion.

• Securely store unused electric tools. Unused electric tools should be stored in a dry, elevated or closed location out of the reach of children.

Machine Use and Care

•

Never turn the drill press on until the table is clear of all foreign objects (tools, scraps, etc.).

• Always keep hands and fingers away from the drill bit.

• Do not drill materials without a flat surface.

• Never start the drill press with the drill bit pressed against the workpiece.

• Make sure the table lock is tightened before starting the drill press.

• Never layout, assemble, or set-up any work on the table while the drill is on.

• Make sure the drill bit is securely locked in the chuck.

• Make sure the chuck key is removed from the chuck before turning power on.

• Adjust the table or depth stop to avoid drilling into the table.

• Always stop the drill before removing scrap pieces from the table.

• Use clamps or a vise to secure a workpiece to the table. This will prevent the workpiece from rotating with the drill bit.

• Do not wear gloves when operating a drill press.

• Set the drill press to the speed that is appropriate for the material being drilled.

• If any part of the drill press is missing/ damaged or if the electrical components fail to perform properly, shut the power OFF and unplug the drill

press. Replace missing, damaged, or failed parts before resuming operation.

• Before leaving the machine, shut the power off, remove the drill bit and clean the table.

• Take care of your tools. Keep cutting tools sharp and clean to be able to work better and more safely. Follow the instructions for lubrication and

for tool replacement. Check the connection cable of the electric tool regularly and have it replaced by a recognized specialist when damaged.

Check extension cables regularly and replace them when damaged. Keep the handle dry, clean, and free of oil and grease.

Residual Risks

Despite proper use, additional residual risks cannot be completely ruled out. The following risks may arise due to the nature of the drill press.

M

echanical hazards related to machine parts or workpieces:

• Shape

• Relative location

• Mass and velocity (kinetic energy of elements in controlled or uncontrolled motion)

• Mechanical strength

• Crushing hazard

• Cutting or severing hazard

• Entanglement hazard

• Drawing-in or trapping hazard

Electrical hazards due to:

• Contact of persons with live parts (direct contact)

• Contact of persons with parts which have become live under faulty conditions (indirect contact)

• Electrostatic phenomena

Hazards generated by noise, resulting in:

• Hearing loss (deafness), other physiological disorders (loss of balance, loss of awareness)

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

• Interference with speech communication, acoustic signals.

Hazards generated by materials and substances (and their constituent elements)

• Processed or used by the machinery

• Hazards from contact with or inhalation of harmful fluids and dusts

• Fire hazard

Hazards generated by neglecting ergonomic principles in machinery design related to:

• Unhealthy postures or excessive effort

• Hand-arm or foot-leg anatomy

• Local lighting

• Mental overload and underload, stress

• Human error, human behaviour

• Design, location, or identification of manual controls

Combination of hazards. Unexpected start up, unexpected overrun/overspeed (or any similar malfunction) from:

• Failure/disorder of the control system

• External influences on electrical equipment

• Errors made by the operator (due to mismatch of machinery with human characteristics and abilities)

• Impossibility of stopping the machine in the best possible conditions

• Variations in the rotational speed of tools

• Failure of the power supply

• Failure of the control circuit

• Errors of fitting

• Break-up during operation

• Falling or ejected objects or fluids

• Loss of stability / overturning of machinery

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

Safety Symbols

The product may have safety warning labels attached to it, explained below. Understand the symbols on your

product and their meanings. If any stickers become unreadable, unattached etc., replace them.

Flammable Material Hazard

Flammable liquids, gases, or

substances etc may present.

Avoid ignition sources and open

flames. Danger of fire.

Read User Manual

Read and fully understand

product safety warnings,

operation, procedures etc before

using the product.

Use Hand Protection

Wear appropriate hand protection

and take due care as the product

or use of the product may present

hand hazards.

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Electrocution / Electrical Shock

Hazard

High voltage or high current

electricity may be present or

required by the product. Take

due care when handling electrical

products, cables, plugs and

leads. Electrical shock can be

fatal.

Toxic Fumes / Dust Hazard

Using the product or by-products

from use may produce fumes,

smoke or particles that could be

harmful if inhaled. Wear

appropriate breathing protection

and have adequate ventilation.

Explosive Material Hazard

Combustible liquids, gases, or

substances etc may be present.

Avoid ignition sources and open

flames. Danger of explosion.

Cutting / Amputation Hazard

The product may have blades,

edges or mechanical devices that

can cause severe cut injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Crush Hazard

The product may have blades,

edges or mechanical devices that

can cause severe crush injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Single Operator Only

The product must be operated by

a single person only. More than

one person operating the product

may introduce additional hazards.

Use Face Protection

Wear appropriate full-face

protection and take due care as

the product or use of the product

may present face and eye

hazards.

Use Foot Protection

Wear appropriate foot protection

and take due care as the product

or use of the product may present

foot hazards.

Use Eye / Ear / Head Protection

Wear appropriate eye and / or

ear and / or head protection and

take due care as the product or

use of the product may present

eye, hearing, and head hazards.

Running Hazard

Do not run on or near the product

as doing so may present a fall

hazard.

Diving Hazard

Do not dive into the product as

doing so may present a neck /

head injury hazard.

Adult Supervision Required

Always supervise children and

other users of a product to

prevent drowning or injury.

Skin Penetration / Puncture

Hazard

The product may produce

pressure, emit liquids or objects

that can cause severe injury to

fingers, limbs, blood etc. Take

due care when handling and

using the product.

Hot Surface Hazard

Be aware that the product may

produce high temperatures and

hot surfaces that can cause burn

injuries.

Flying Debris Hazard

Be aware that the product or use

of the product may present

hazards produced by flying

debris. Wear appropriate clothing

and protective devices.

Moving Parts Hazard

Be aware that the product

contains or uses mechanical

devices that move or rotate.

Always wait for moving parts to

stop fully before handling the

product, adjusting, maintenance

etc.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Pull Hazard

Be aware that the product

contains or uses mechanical

devices that can pull in objects

and can cause severe injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Slope / Fall Injury Hazard

Be aware that using the product

on sloping surfaces or in slippery

conditions may present additional

dangers from falls and contact

with blades, moving parts, hot

surfaces etc.

"Slam Dunk" Warning

Do NOT attempt "slam dunk"

manoeuvres as this may result in

severe injury due to falling,

product breakage or collapse etc.

Electrocution / Electrical Shock

Hazard - Outdoor

High voltage or high current

electricity may be present or

required by the product. Do NOT

use in rain, damp, or wet

conditions. Electrical shock can

be fatal.

Electrocution / Electrical Shock

Hazard - Disconnect

High voltage or high current

electricity may be present or

required by the product. Always

disconnect the product from the

electrical supply before handling

the product, adjusting,

maintenance etc.

Power Line Electrocution

Hazard

High voltage / high current power

lines may be present. Use

extreme caution to avoid contact

or interference with power lines.

Electrical shock can be fatal.

"Kick-Back" Hazard

High level of "kick-back" hazard

that can cause the machine to

suddenly rotate towards operator.

Kick-back injury can be fatal.

Winch Operator Position

Hazard

Do NOT stand between winch

and load. Do NOT use winch to

move people.

Winch Lift Hazard

Do NOT LIFT load vertically. Use

machine to PULL only.

Cable Hazard

Ensure that load bearing cable is

not kinked or knotted.

Winch Cable Hazard

Ensure that there is a minimum

number of cable coils on

winching mechanism.

Winch Hook Hazard

Carry hook to load – do NOT

throw or run.

Flash / Blinding Hazard

Wear appropriate eye protection

for welding. Direct exposure to

weld arcs may cause permanent

eye injury.

Laser Hazard

Laser may be in use – do NOT

look directly at laser or allow

others to.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

Table of Contents

Safety ............................................................................................................................................................. 2

Safety Symbols ........................................................................................................................................................... 6

Contents Supplied ........................................................................................................................................ 9

Assembly ..................................................................................................................................................... 10

Column Tube ............................................................................................................................................................ 10

Drilling Bench ............................................................................................................................................................ 11

Machine Head ........................................................................................................................................................... 14

Drill Chuck Guard ..................................................................................................................................................... 15

Drill Chuck ................................................................................................................................................................ 16

Drill Lifting Arms ........................................................................................................................................................ 17

Drill Chuck Key ......................................................................................................................................................... 18

Depth Stop ................................................................................................................................................................ 19

Plier (Optional- Sold Separately) .............................................................................................................................. 20

Features and Controls ................................................................................................................................ 21

Set-Up .......................................................................................................................................................... 22

Selecting the Speed.................................................................................................................................................. 22

Tensioning the V-belts .............................................................................................................................................. 24

Adjusting the Drilling Bench ...................................................................................................................................... 25

Changing the Drill Bit ................................................................................................................................................ 28

Operation ..................................................................................................................................................... 29

Drilling ....................................................................................................................................................................... 29

General Drilling Guidelines - Drilling A Hole ............................................................................................................. 29

Drilling Metal ............................................................................................................................................................. 29

Drilling Wood ............................................................................................................................................................ 30

Emergency Stop Switch ........................................................................................................................................... 30

Maintenance ................................................................................................................................................ 31

Servicing ................................................................................................................................................................... 31

Cleaning .................................................................................................................................................................... 31

Transportation and Storage .......................................................................................................................

32

Transportation ........................................................................................................................................................... 32

Storage ..................................................................................................................................................................... 32

Troubleshooting ......................................................................................................................................... 33

Specifications ............................................................................................................................................. 35

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

Contents Supplied

The drill press comes partially assembled and is shipped in carefully packed carton. After all the parts have been

removed from the carton, you should have:

No. Name No. Name

1 Machine Head 11 Collar

2 Column Tube 12 Height Crank

3 Drilling Bench 13 Depth Stop

4

Drill Chuck

14

Drill lifting arm (x3)

5

Drill Chuck Guard

15

Allen Key, 5mm

6

Baseplate

16

Allen Key, 4mm

7

Drill Chuck Key

17

Allen Key, 3mm

8 Rack 18

Hardware Bag: M8x20 (x4)

Optional: M10x35 (x2)

9

Plier (Optional -

Sold Separately)

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

Assembly

This drill press was partially assembled at the factory. To assemble your machine, follow the below instructions.

Column Tube

Place the column tube on the baseplate. Bolt the column tube to the baseplate with the four screws M8×20

supplied. Tighten the screws moderately tight with an open-end wrench SW 13 (not scope of delivery) so that

the threads in the baseplate do not strip.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

Drilling Bench

1. Place the drilling bench holder over the rack. The teeth of rack must mesh with the teeth of gear. See below

illustration 1.

2. Slide the drilling bench on the column tube. Make sure the bottom bevel of rack insert into the bottom disc of

the column tube. See below illustration 2.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

3. Slide the collar over the column tube with bevelled edge facing down until it presses against the top of the

rack. See below illustration 3.

4. Tight the set screw, but do not overtighten it. See below illustration 4.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

5. Slide the height crank over the shaft on the side of drilling bench. See below illustration 5.

6. Secure the height crank to the shaft using the Allen key 3mm. See below illustration 6.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

Machine Head

Place the machine head on the column tube and secure the machine head with the two grub screws to the side

with the Allen key 4mm.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

Drill Chuck Guard

Put the drill chuck guard on the upper part of the drill spindle. Secure the drill chuck guard with a screwdriver

(not scope of delivery).

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

Drill Chuck

Fold the drill chuck guard upwards. Insert the drill chuck on the taper of the drill spindle. Push the drill chuck onto

the drill spindle with a few light taps. Use a plastic hammer for this purpose.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

Drill Lifting Arms

Bolt the three drill lifting arms into the hand spindle guide. Tighten the three-hole lifting arms with an open-end

wrench SW 6 (not scope of delivery).

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

Drill Chuck Key

Attach the drill chuck key into the key holder.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

Depth Stop

1. Remove the washer and nut from the depth stop. See below illustration 1.

2. Insert the depth stop through the hole in the fence. See below illustration 2.

3. Screw the depth stop with washer and nut that just had been removed from step 1. Centrally align the depth

stop into the bore of the fence. See below illustration 3.

4. The home position of pointer should be 0mm. See below illustration 4.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

Plier (Optional- Sold Separately)

The plier is optional, with bolts, flat washers and nuts mounted on the drilling bench or the baseplate.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

Features and Controls

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

Set-Up

Place the drill press on a solid flat surface. Ideally, bolt the drill press to the surface. Use the two holes in the

baseplate for this.

Selecting the Speed

1. Release the locking screw on the gear cover with the Allen key 5mm.

2. Pull the locking screw and open the gear cover.

3. Loosen the motor tension knob on each side of the headstock.

4. Slide the motor forward a little to release the load on the V-belts. See below illustration 2.

5. Remove the V-belt between idle pulley and motor pulley first, then slide idle pulley towards the spindle pulley

to release the load on the V-belt between idle pulley and spindle pulley. Remove the second V-belt. See

below illustration 2 & 3.

6. Place the two V-belts on the desired assembly to reach the specified speed.

7. Slide the motor back to tension the V-belts again. The V-belts are correctly tensioned when it gives way

slightly when pressed. Deflection distance of belt is 5-10mm.

8. Lock this position with the two motor tension knobs.

9. Close the gear cover. Fasten the locking screw on the gear cover with the Allen key 5mm.

The gear cover is equipped with a interlock switch. If the gear cover is not closed correctly, the

device cannot be switched on.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

Recommended speeds for different drill sizes and materials:

Tensioning the V-belts

1. Release the locking screw on the gear cover.

2. Open the gear cover.

3. Loosen the motor tension knob on each side of the headstock.

4. Slide the motor back to tension the V-belts.

5. The V-belts are correctly tensioned when it gives way lightly when pressed. Deflection distance of belt is 5-

10mm.

6. Tighten the two motor tension knobs.

7. Close the gear cover. Fasten the locking screw on the gear cover with Allen key 5mm.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

Adjusting the Drilling Bench

1. Release the locking handle. See below illustration 1.

2. Rotate the height crank clockwise or anti-clockwise to the desired height. See below illustration 2.

3. Pivot the drilling bench to the desired position.

4. Fasten the drilling bench again with the locking handle. See below illustration 3.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

5. You can also adjust the tilt angle of the drilling bench. To do this, release the retaining screw under the

drilling bench with an open-end wrench SW 19 (not scope of delivery). Tilt the drilling bench as desired to

the right or left up to a max. of 45° and secure the drilling bench again with the retaining screw.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

Changing the Drill Bit

Remove the plug from the mains socket before changing the bit. This will prevent an accidental start-up.

1. Fold the drill chuck guard up.

2. Release the retaining jaws of the drill chuck with the drill chuck key.

3. Remove the bit.

4. Insert a new bit.

5. Tighten the retaining jaws of the drill chuck with the drill chuck key.

6. Check that the bit is centred.

7. Fold the drill chuck guard down again.

8. Attach the drill chunk key back to the key holder.

Under no circumstances must you leave the drill chuck key inserted.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

Operation

Always place a piece of backup material (wood, plywood, etc.) on the table underneath the

workpiece. This will prevent splintering on the underside of the workpiece as the drill bit breaks

through. To keep the material from spinning out of control, it must contact the left side of the column, or

be clamped (not included) to the table.

For small workpieces that cannot be clamped to the table, use a drill press vise (not included). The vise

must be clamped or bolted to the table to avoid injury.

Drilling

1. Starting the drill press.

− The drill press can be switched on by pressing the green ON switch ''I''.

− The red OFF switch ''0'' has to be pressed to switch off the drill press.

2. Turn one of the drill lifting arms anti-clockwise.

3. The drill chuck is lowered.

4. Drill into the workpiece at the appropriate feed rate and to the desired depth.

5. Be aware of any necessary chip breaking on the way to the desired depth.

6. Move the bit slowly back to the stop position.

General Drilling Guidelines - Drilling A Hole

WARNING! To prevent the workpiece and the backup material from slipping from your hand

while drilling, position the workpiece and backup material to the left side of the column. If the

workpiece and the backup material are not long enough to reach the column, clamp the workpiece and

backup material to the table. Failure to do this could result in personal injury.

1. Mark where you want to drill the workpiece by using a center punch or a sharp nail.

2. Before turning the drill press ON, turn the drilling lifting arms to bring the drill bit down. Line the drill bit tip up

with the mark. Clamp the workpiece in place.

3. Turn ON the drill press and pull down on the drilling lifting arms with the appropriate force needed to allow

the drill bit to drill the material.

NOTE: Feeding too slowly might cause the drill bit to turn in the chuck. Feeding too rapidly might

stop the motor, cause the belt to slip, force the workpiece loose, or break the drill bit. Practice

with scrap material to get the feel of the machine before attempting to do any drilling operation.

Drilling Metal

•

Use metal-piercing twist drill bits.

•

It is always necessary to lubricate the tip of the drill with oil to prevent overheating of the drill bit.

•

All metal workpieces should be clamped down securely. Any tilting, twisting, or shifting causes a rough drill

hole, and increases the potential of drill bit breakage.

•

Never hold a metal workpiece with your bare hands. The cutting edge of the drill bit may seize the workpiece

and throw it, causing serious injury. The drill bit will break if the metal piece suddenly hits the column.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

•

If the metal is flat, clamp a piece of wood under it to prevent turning. If it cannot be laid flat on the table, then

it should be blocked and clamped.

Drilling Wood

•

Brad point bits are preferred. Metal piercing twist bits may be used on wood.

•

Do not use auger bits. Auger bits turn so rapidly that they can lift the workpiece off of the table and whirl it

around.

•

Always protect the drill bit by positioning the table so that the drill bit will enter the center hole when drilling

through the workpiece.

•

To prevent splintering, feed the drill bit slowly right as the bit is about to cut through to the backside of the

workpiece.

•

To reduce splintering and protect the point of the bit, use scrap wood as a backing or a base block under the

workpiece.

Emergency Stop Switch

WARNING! When encountering incidental situation, such as, hand getting drilled, hair getting

caught, sudden failure of machine or other situations where you need to stop the operation in an

emergency, please press the emergency stop switch immediately, the machine will automatically cut-out

to protect the operator.

Unplug the power cord before other operations. After the danger is dismissed, turn the emergency stop

switch by direction of arrows (clockwise) until it pops out (reset). The machine is in an open circuit state

now, plug the power cord and operate normally.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

Maintenance

WARNING! For your safety, turn the switch off and remove the plug from the power supply. Wait

until the rotating tool stands still. All protection and safety devices must be immediately re-

installed once the repair and maintenance work is completed.

CAUTION! All servicing of the drill press should be performed by a qualified service technician.

Servicing

•

Pull the mains plug before any adjustments, maintenance, or repair.

•

Have any work on the device that is not described in this instruction guide performed by a professional. Only

use original parts. Allow the device to cool off before any maintenance or cleaning is undertaken.

•

There is a risk of burning!

•

Always check the device before using it for obvious defects such as loose, worn or damaged parts, correct

the positioning of screws or other parts. Exchange the damaged parts.

•

The ball bearings in the spindle and the V-belt pulley assembly are greased and permanently sealed. Pull

the spindle down and oil the spindle sleeve moderately every three months.

•

Lubricate the table bracket and locking knobs if they become difficult to use.

Cleaning

•

Do not use any cleaning agents or solvents. Chemical substances can etch the plastic parts of the device.

Never clean the device under running water.

•

Thoroughly clean the device after every use.

•

Clean the ventilation openings and the surface of the device with a soft brush or cloth.

•

Remove chips, dust, and dirt with a vacuum cleaner if necessary.

•

Lubricate moving parts regularly.

•

Vacuum sawdust or metal shavings that accumulate in and on the motor, pulley housing, table, and work

surface.

•

Apply a light coat of paste wax to the column and table to help keep these surfaces clean and rust-free.

•

Do not allow lubricants to come into contact with switches, V-belts, pulleys and drill lifting arms.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

Transportation and Storage

Transportation

•

Unplug the machine from the mains during transport.

•

The machine must only be lifted and transported on its belt housing. Never lift the machine at the safety

devices, the adjusting levers, or the drill chuck.

Storage

DANGER! Store the drill press a way it cannot be started by unauthorised persons and that

nobody can get injured.

CAUTION! Do not store the drill press unprotected outdoors or in a moist environment.

•

Store the device and its accessories in a dark, dry, and frost-proof place that is inaccessible to children. The

optimum storage temperature is between 5 and 30˚C.

•

Store the electrical tool in its original packaging.

•

Cover the electrical tool to protect it from dust and moisture.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

Troubleshooting

Problem Cause Remedy

Device doesn’t start.

No mains voltage. Main circuit breaker

is tripped.

Check the socket, mains supply cable,

cord, mains plug; if necessary, have

them repaired the main fuse.

ON switch (green) / OFF Switch (red)

(1) is broken.

Take to a qualified service centre or

technician

Motor is faulty

Take to a qualified service centre or

technician

No Motor output turns off

automatically

Motor not fixed in place.

Check the tension of the V-belts and

tighten the clamping screw.

Bit not centrally clamped. Check the bit in the drill chuck.

Loud squeaking noise.

Incorrect belt tension Adjust the belt tension

Dry spindle Lubricate the spindle

Loosed spindle pulley

Tighten the retaining nut on the pulley

insert

Loosed motor pulley

Tighten the set screw on the side of

the motor pulley

The drill bit burns or smokes

Drilling at the incorrect speed Change the speed

The wood chips are not coming out of

the hole

Retract the drill bit frequently to clear

the chips

Dull drill bit Resharpen or replace the drill bit

Feeding the workpiece too slowly Feed fast enough to cut the workpiece

Not lubricated Lubricate the drill bit with cutting oil

Excessive drill run out or

wobble; drilled hole is not round

Bent drill bit Replace the drill bit

Bit improperly installed in the chuck Reinstall the bit.

Worn spindle bearings

Replace the bearing. Take the press

to a qualified service technician

Lengths of cutting flutes or angles not

appropriate for the hardness of the

wood grain

Resharpen the drill bit correctly or

replace with the appropriate type.

Chuck not properly installed Reinstall the chuck.

Drill bit binds in the workpiece

The workpiece is pinching the bit Support or clamp the workpiece.

Excessive feed pressure Feed more slowly.

Spindle returns too slowly or

too quickly

Coil spring has improper tension Adjust the coil spring tension

Chuck falls off spindle

Dirt, grease, or oil on the tapered

surface on the spindle or in the chuck

Clean the tapered surface of both the

chuck and spindle with a household

detergent.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

Problem Cause Remedy

Motor will not run

Defective or broken switch

Take to a qualified service centre or

technician

Defective or damaged power cord

Take to a qualified service centre or

technician

Open circuit, loose connections, or

burned-out motor

Take to a qualified service centre or

technician

Low voltage

Check the power line for the proper

voltage. Use another circuit or have a

qualified technician check on it.

Motor stalls

Short circuit in motor Take to a qualified service technician

Incorrect fuses or circuit breakers

Replace with correct fuse or circuit

breaker for the circuit

Overloaded circuit Turn off other machines and retry

Low Voltage

Check the power line for the proper

voltage. Use another circuit or have a

qualified electrician upgrade the

service.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

DP15 Drill Press

Specifications

Motor 600W Brushless

Chuck 16mm Stainless Steel

Number of Speeds 12

Variable Speeds (rpm)

420 / 600 / 680 / 770 / 900 / 1000 / 1100 /

1220 / 1400 / 1980 / 2200 / 2700

Drill Travel 60mm

Swing 252mm/10”

Spindle Feed Rack and Pinion

Spindle to Table 410mm

Spindle to Base 525mm

Table diameter 195mm

Table Tilt ±45°

Switches Dust Protected NVR

Note: Minimal Assembly required

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Some experts believe that the incorrect or prolonged use of almost any

product may cause serious injury or death. To help reduce your risk of

serious injury or death, refer to the information below. For more information,

see www.datastreamserver.com/safety



Consult all documentation, packaging,

and product labelling before use. Note

that some products feature

documentation available online. It is

recommended to print and retain the

documentation.



Before each use, check the product for

loose/broken/damaged/missing parts,

wear, or leaks (if applicable). Never use a

product with

loose/broken/damaged/missing parts,

wear, or leaks.



Products must be inspected and serviced

(if applicable) by a qualified technician

every 6 months. This is based on

average residential use by persons of

average size and strength, and on a

property of average metropolitan size.

Use beyond these recommendations may

require more frequent

inspections/servicing.



Ensure that all users of the product have

completed a suitable industry recognised

training course before being allowed

access to the product.



The product has been supplied by a general merchandise

retailer that may not be familiar with your specific

application or description of application. Be sure to attain

third-party approval from a qualified specialist for your

application before use, regardless of any assurances from

the retailer or its representatives.



This product is not intended for use where fail-safe

operation is required. As with any product (for example,

automobile, computer, toaster), there is the possibility of

technical issues that may require the repair or

replacement of parts, or the product itself. If the possibility

of such failure and the associated time it may take to

rectify could in any way inconvenience the user, business,

or employee, or financially affect the user, business, or

employee, then the product is not suitable for your

requirements. This product is not intended for use where

incorrect operation or a failure of any kind, including but

not limited to, a condition requiring product return,

replacement, parts replacement, or service by a

technician may cause financial loss, loss of employee

time or an inconvenience requiring compensation.



If this product has been purchased in error when

considering the information presented here, contact the

retailer directly for details of their returns policy, if

required.

ideas, diagrams, or images may be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying, scanning, or recording, or any information storage and retrieval system,

without express permission or consent from the publisher.

BAUMR-AG DP15 600W 10" Pedestal Bench Drill Press DRLDPRBMRAD15

Product's Documents

Product manual

Specifications

BAUMR-AG DRLDPRBMRAD15 Questions and Answers