Loading ...
Loading ...
Loading ...
Dolby Pro Logic (N on-Digital) – Line Level
8
9
Use this installation method
for Dolby P ro Logic appli-
cations (not Dolby Digital, DTS
or other digital proc essing),
w here the rec eiver/proc essor
is equipped w ith a subw oofer
output, or a volume-controlled
preamp (line-) level output:
Use RCA -type patch c ords
to c onnec t the line-level
subw oofer outputs on your
rec eiver or amplifier to the
line-level inputs on the
subw oofer. IM P ORTAN T: Do
not use the LFE input on the
subw oofer w ith Dolby
P ro Logic proc essors. N ote: If
your rec eiver or amplifier only
has one subw oofer output
jac k, then you w ill need to use
a Y-c onnector (not included).
P lug the male end of the Y-
connec tor into your rec eiver
or amplifier’s subw oofer
output jac k, and c onnec t each
of the tw o female ends to
separate RCA -type patch
cords. Finally, plug the RCA -
type patch c ords into the line-
level inputs on the subw oofer.
Connect eac h speaker to
the c orresponding speaker
terminals on your rec eiver
or amplifier.
Use this installation method
for Dolby Digital, DTS or other
digital surround proc essors:
Use the line-level input jack
marked “LFE” for the Low -
Frequenc y Effec ts c hannel.
Connect this jac k to the LFE
output or subw oofer output
on your rec eiver or amplifier.
Connect eac h speaker to the
corresponding speaker
terminals on your rec eiver
or amplifier.
M ake sure that you have
configured your surround-
sound proc essor for
“Subw oofer On.” The front
left, front right, center and
rear speakers should all be
set to “S mall.”
Dolby Digital or DTS (or Other Digital Surround M ode) Connection
O P E R A T I O N
MIN MAX
Subwoofer�
Level
MIN MAX
Subwoofer�
Level
M ove the M aster P ow er
sw itc h (marked “P ow er”
¡
)
to the “
•
” (On) position to use
the subw oofer. The S CS135
subw oofer w ill automatic ally
turn itself on or go into
standby (sleep) mode w hen
left in the standby mode
(“A uto/On” sw itch
™
in the
“A uto” position). W hen your
rec eiver or amplifier is off, or
is not sending program
material to the subw oofer,
the subw oofer w ill be in
standby mode. W hen the sub-
w oofer senses an audio signal,
it w ill automatic ally turn itself
on. If the subw oofer does
not sense a signal after
approximately tw enty minutes,
it w ill automatic ally go into
standby mode.
W hen the “A uto/On” sw itch
™
is sw itched to the “On”
position, the subw oofer w ill
remain on, w hether or not
program material is playing.
If you w ill be aw ay from
home for an extended period
of time, or if the subw oofer
w ill not be used, sw itc h the
M aster P ow er sw itch
¡
to
the Off position.
Volume
POWER
HIGH LEVEL
+ – – +
SUBWOOFER
LEVEL
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
OUT
IN
L R
LINE LEVEL IN
LFE
L
R
AUTO ON
MI N M AX
SUB 135
AC 120V~60Hz
200 Watts
FUSE
2.5A/250V
TYPE T
£�
¡�
™�
IMPORTANT: CONNECT STRIPED WIRE TO RED ( ) SPEAKER TERMINAL.
GREEN: ON
RED: STANDBY
+
LINE LEVEL IN
LFE INPUT
LFE OUT
L
R
SUBWOOFERRECEIVER
Volume c an be adjusted
using the Subw oofer Level
Control
£
(above), as show n
below.
+ –
+ –
+ –
+ –
+ –
+ –
+ –
+ –+ –
+ –
Receiver
Subwoofer �
Out
Left�
Front�
�
Left�
Rear
Right�
Front
Right�
Rear
Subwoofer
R L
R
L
Center
Line-�
Level�
In
Right Surround
Right Front
Left Surround
Left Front
Center
Loading ...
Loading ...