Loading ...
Loading ...
Loading ...
NOTE: To prolong the life of your steam
mop, we recommend using distilled water.
NOTE: Sweep or vacuum your floors prior
to cleaning with your steam mop.
1 Make sure both pads are properly installed
before using.
2 Twist the quick-release cord holder
to unwrap the power cord completely
(fig. 5). Plug into an electrical outlet.
3 When it's first plugged in, the unit will be
in Standby mode. The 3 settings will blink
to indicate Standby mode.
4 To select the steam mode (fig. 6), press
the mode button. Once the mode is
selected, tilt the handle down to activate
the spinning pads (fig. 7).
TIP: If the handle is not reclined, the mode
selection may time out and pads will
not spin.
TIP: When cleaning near baseboards,
edges, or furniture, you may feel a slight
pull from the unit making contact with
these surfaces. This is normal and not a
cause for concern.
5 Mop with a forward and backward motion.
6 When finished mopping, press the mode
button until you've reached Standby
mode. The settings lights will blink,
indicating that the unit is in Standby mode.
Once in Standby mode, lift the handle to
bring the steam mop back to the upright
position and unplug the unit.
7 When the pads have cooled completely,
remove them by pulling them o the discs.
8 When the water tank is empty, the unit
will stop producing steam. Make sure the
unit is unplugged before refilling the water
tank.
NOTE: Please wait 2 to 3 minutes for the
steam mop to cool o before removing the
Dirt Grip® pads. NEVER leave the steam
mop with damp or wet Dirt Grip pads on
any floor for an extended period.
The Shark
®
Steam & Scrub steam mop has 3 unique Intelligent Steam Control settings so you
can select the ideal amount of steam to use for each cleaning task. In NORMAL mode, the pads
will spin faster and more steam will be produced than in LIGHT mode. In DEEP mode, the pads
will spin the fastest and the maximum amount of steam will be produced. See below for tips on
when to use each setting.
SETTING IDEAL FOR THESE
SEALED SURFACES
RECOMMENDED USAGE
LIGHT
Laminate
Hardwood
Vinyl
Cleaning delicate surfaces
Light cleaning and dusting
Loosening and lifting light dirt
NORMAL
Marble
Tile
Stone
Basic, everyday cleaning
Cleaning large areas
Cleaning moderate and heavy trac areas
DEEP
Marble
Tile
Stone
Reaching hard-to-clean surfaces
Tough cleaning and removing stuck-on
messes and stains
Deep cleaning heavy trac areas
Cutting through heavy dirt and grime
Sanitizing* floors
fig. 5 fig. 6 fig. 7
fig. 8
TO SANITIZE*:
1 Attach clean Dirt Grip® Soft Scrub Pads to the scrubbing mop head.
2 Plug in the unit, tilt the mop handle down, and press the mode button to select the DEEP
setting. The pads will then start spinning.
3 Wait 30 seconds for the unit to begin producing steam.
4 Start mopping with a forward and backward motion on an appropriate sealed hard floor sur-
face. After three minutes, your unit will be ready to sanitize.
5 Using a forward and backward motion, move the mop head slowly and evenly over the area to
be sanitized while applying continuous downward pressure. Slowly repeat at least 15 times.
* Sanitization studies were conducted under controlled test conditions. Household conditions
and results may vary. With mop head in DEEP mode.
STEAM BLASTER®:
1 To target tough messes with an extra burst of cleaning
power, move the front of the nozzle 2 to 4 inches from
the mess (fig. 8), then press and hold the Steam Blaster
button as needed. (Hold longer for the toughest messes.)
2 Before scrubbing, wait 5 seconds to let the steam blast
penetrate the mess.
Tip: For more dicult messes, allow 20 seconds or more.
USING YOUR STEAM & SCRUB INTELLIGENT STEAM CONTROL®
sharkclean.comsharkclean.com
Loading ...
Loading ...
Loading ...