Dewalt DCN890P2 Instruction Manual

Loading ...

ENGLISH

Fig. N

7. Lift the rear of driver until at an angle and pull the driver

out. Refer to FigureO.

8. Replace driver and follow steps in reverse to reassemble

9. Ensure new driver slides smoothly through the gun

before fullreassembly.

Fig. O

10. Return the driver, guide rods, bumpers, housing end

cap, and removable top stand back onto the unit. It

is important to try the alignment of the driver and

the flywheel before screwing the housing end cap

back on to the unit. This can be done by connecting

a battery and pushing then releasing the nose of the

unit against a bench or hard surface. This will start the

motorspinning.

NOTE: When the driver and the flywheel are correctly

aligned, you will hear the motor coast back down

from full speed. If the driver and the flywheel are not

correctly aligned, the motor may not start up, may

slow down much faster than normal along with a loud

grinding noise from the unit. If this happens remove

and reseat the driver, making sure the bumpers are

seatedcorrectly.



WARNING: Always test the unit by firing 3/4" pins

in power setting 1 into scrap material, to ensure that

the tool is working properly. If tool does not operate

properly, contact a recognized

DEWALT

service

centerimmediately.

Recommended accessories for use with your tool are

available at extra cost from your local dealer or authorized

service center. If you need assistance in locating any

accessory, please contact

DEWALT

Industrial Tool Co., 701

East Joppa Road, Towson, MD 21286, call 1–800–4-

DEWALT

(1–800–433–9258) or visit our website www.

DEWALT

.com.

Repairs

The charger and battery pack are notserviceable.



WARNING: To assure product SAFETY and

RELIABILITY, repairs, maintenance and adjustment

(including brush inspection and replacement) should

be performed by a

DEWALT

factory service center

or a

DEWALT

authorized service center. Always use

identical replacementparts.

Thank you for your purchase. Register your product nowfor:

• WARRANTY SERVICE: Registering your product will

help you obtain more efficient warranty service in case

there is a problem with yourproduct.

• CONFIRMATION OF OWNERSHIP: In case of

an insurance loss, such as fire, flood or theft, your

registration of ownership will serve as your proof

ofpurchase.

• FOR YOUR SAFETY: Registering your product will

allow us to contact you in the unlikely event a safety

notification is required under the Federal Consumer

SafetyAct.

Three Year Limited Warranty

DEWALT

will repair, without charge, any defects due to

faulty materials or workmanship for three years from

the date of purchase. This warranty does not cover part

failure due to normal wear or tool abuse. For further detail

of warranty coverage and warranty repair information,

visit www.dewalt.com or call 1-800-4-

DEWALT

(1-800-

433-9258). This warranty does not apply to accessories

or damage caused where repairs have been made

or attempted by others. THIS LIMITED WARRANTY IS

GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED

WARRANTY OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL

OR CONSEQUENTIAL DAMAGES. Some states do not allow

limitations on how long an implied warranty lasts or the

exclusion or limitation of incidental or consequential

damages, so these limitations may not apply to you. This

warranty gives you specific legal rights and you may have

other rights which vary in certain states orprovinces.

In addition to the warranty,

DEWALT

tools are covered

byour:

1 YEAR FREE SERVICE

DEWALT

will maintain the tool and replace worn parts

caused by normal use, for free, any time during the first year

afterpurchase. ADD WEAR STATEMENT: NO SPRINGS

2 YEARS FREE SERVICE ON DEWALT BATTERY PACKS

DC9071, DC9091, DC9096, DC9182, DC9280, DC9360, DCB120,

DCB127, DCB201, DCB203, DCB203BT, DCB207, DCB361

Loading ...

Dewalt DCN890P2 20V MAX XR Cordless Concrete Nailer Kit

Instruction Manual - Page 17