Loading ...
Loading ...
Loading ...
ENGLISH
8
Installing and Removing the Battery Pack
(Fig. D)
NOTE: For best results, make sure your battery pack is
fullycharged.
To install the battery pack
1
into the tool handle, align the
battery pack with the rails inside the tool’s handle and slide
it into the handle until the battery pack is firmly seated in
the tool and ensure that it does notdisengage.
To remove the battery pack from the tool, press the release
button
2
and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of thismanual
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and lock off the toolremove
the battery pack before making any adjustments
or removing/installing attachments or
accessories. An accidental start-up can causeinjury..
Fig.B
11
9
10
Belt Hook and Bit Clip (Fig. B)
Optional Accessory
WARNING: To reduce the risk of serious personal
injury, ONLY use the tool’s belt hook to hang
the tool from a work belt. DO NOT use the belt
hook for tethering or securing the tool to a person or
object during use. DO NOT suspend tool overhead or
suspend objects from the belthook.
WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook
issecure.
IMPORTANT: When attaching or replacing the belt hook or
bit clip, use only the screw
11
that is provided. Be sure to
securely tighten thescrew.
The belt hook
9
and bit clip
10
can be attached to either
side of the tool using only the screw
11
provided, to
accommodate left- or right- handed users. If the belt hook
or bit clip is not desired at all, they can be removed from
thetool.
To move the belt hook or bit clip, remove the screw that
holds it in place then reassemble on the opposite side. Be
sure to securely tighten thescrew.
Mode Selection (Fig. A)
The mode selection collar
5
is clearly marked with numbers
and the max position.The collar should be rotated until the
desired setting is located at the top of the tool.
WARNING: When the mode selection collar is in the
Max position, the drill will not clutch. The drill may
stall if overloaded, causing a sudden twist.
Symbol Mode
MAX Drilling
1–15 Screwdriving (higher number = greater torque)
Fig.C
7
6
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and lock off the toolremove
the battery pack before making any adjustments
or removing/installing attachments or
accessories. An accidental start-up can causeinjury.
Intended Use
This screwdriver is designed for professional
screwdrivingapplications.
DO NOT use under wet conditions or in presence of
flammable liquids orgases.
This screwdriver is a professional power tool. DO NOT let
children come into contact with the tool. Supervision is
required when inexperienced operators use thistool.
impede air flow. Use the back of the charger as a template
for the location of the mounting screws on the wall. Mount
the charger securely using drywall screws (purchased
separately) at least 1” (25.4 mm) long, with a screw head
diameter of 0.28–0.35” (7–9mm), screwed into wood to an
optimal depth leaving approximately 7/32” (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in theslots.
Quick-Release Chuck (Fig. A, C)
NOTE: The chuck accepts 1/4" (6.35 mm) hex accessories
and 1" (25.4 mm) bit tips only.
Place the forward/reverse button
4
in the lock-off
(center) position and remove battery pack before
changingaccessories.
To install an accessory, fully insert the accessory into the
quick-release chuck
6
. The accessory is locked into place
(Fig.A, C).
To remove an accessory, pull the chuck collar
7
away
from the front of the tool. Remove the accessory from the
quick-release chuck
6
(Fig.A, C).
Loading ...
Loading ...
Loading ...