Loading ...
Loading ...
Loading ...
10
MAKING HOT MILK (WITHOUT FROTH)
(ECP3X30 ONLY)
To make hot milk without froth, proceed as described in the
above section, making sure the ring (A10) on the cappuccino
maker is positioned upwards in the “HOT MILK” position.
CLEANING THE CAPPUCCINO MAKER AFTER USE
Important! For hygiene reasons, the cappuccino maker
should always be cleaned after use.
Proceed as follows:
1. Turn the steam dial to the position (steps 2- 6 and
7 of the cap. “How to make cappuccino”. This causes the
cappuccino maker to discharge any milk left inside. Turn
the steam dial to 0 position and the selector dial to ON
position;
2. Wait for a few minutes to allow the steam spout to cool.
Unscrew the cappuccino maker by turning it clockwise (g.
20) and wash it thoroughly with warm water;
ECP3X30 model
3. Remove the nozzle from by pulling it downwards (g. 21);
4. Move the ring upwards and make sure the hole shown by
the arrow in g. 22 is not blocked. If necessary, clean with
a pin;
5. Replace the nozzle, move the ring downwards and put the
cappuccino maker back on the nozzle, turning it and push-
ing it upwards until it is attached.
ECP3X20 model
3. Remove the nozzle from by pulling it downwards(g. 23);
4. Make sure the holes shown in g. 24 are not blocked. If
necessary, clean with a pin;
5. Replace the nozzle and the cappuccino maker back on
the nozzle, turning it and pushing it upwards until it is
attached.
HOT WATER
1. Turn the appliance on by turning the selector dial to ON
(g. 4). Wait the READY indicator light comes on;
2. Place a recipient under the cappuccino maker;
3. When the READY indicator light comes on, turn the se-
lector dial to the position and at the same time,
rotate the steam dial to the position: Hot water is
delivered from the cappuccino maker;
4. To interrupt delivery of hot water, rotate the steam dial to
0 position and turn selector dial to ON.
You should not deliver hot water for more
than 60 seconds.
CLEANING
Cleaning the machine
The following parts of the machine must be cleaned regularly:
- the drip tray (A14)
- the coee lters (C2, C3 and C4);
- the boiler outlet (A12);
- the water tank ( A1);
- the cappuccino maker (A7) as described in section “Clean-
ing the cappuccino maker after use”.
Important!
• Do not use solvents, abrasive detergents or alcohol to clean
the coee machine.
• Do not use metal objects to remove encrustations or coee
deposits as they could scratch metal or plastic surfaces.
Danger! While cleaning, never immerse the coee
maker in water. It is an electrical appliance.
Please note:
If the appliance is not used for more than 3/4 days, before using it again, we strong-
ly recommend you rinse the internal circuits through as described in Setting up the
appliance”.
Cleaning the drip tray
Important!
The drip tray is tted with a level indicator (red) showing the
level of water it contains. Before the indicator protrudes from
the cup tray (g. 25), the drip tray must be emptied and cleaned,
otherwise the water may overow the edge and damage the
appliance, the surface it rests on or the surrounding area.
1. Remove the drip tray (g. 26);
2. Remove the cup tray, empty the water and clean the drip
tray with a cloth, then reassemble the drip tray. Extract the
mug of high glass tray (A13), clean with water, dry and put
it back in its housing;
3. Put the drip tray back in place.
Cleaning the coee lters
Clean the coee lters weekly:
1 and 2 cup lters
1. Extract the perforated lter by pulling the tab (g. 27);
2. Rinse the lters under running water (g. 28);
3. Make sure the holes are not blocked. If necessary, clean
with a pin (gs. 28 and 29);
4. Place the perforated lter in the lter housing and press as
far as it will go.
Pod lter
Rinse under running water. Make sure the holes are not blocked.
If necessary, clean with a pin (gs. 28 and 29).
Loading ...
Loading ...