Loading ...
Loading ...
Loading ...
11
ENGLISH
Trimming (Fig.K—M)
WARNING:
Keep the rotating string
roughly parallel with the ground (tilted no more
than 10degrees). This trimmer is not an edger. DO
NOT TILT the trimmer so that the string is spinning
near a right angle to the ground. Flying debris can
cause seriousinjury.
CAUTION:
Ensure that other persons and
pets are at least 100' (30 m) away. Flying debris can
cause seriousinjury.
1. With the trimmer on, angle it and swing side to side as
shown in Fig.L.
2. Maintain a cutting angle of 5° to 10°. Do not exceed
10°. Cut with the tip of the line.
3. Maintain a minimum distance of 24" (610 mm) between
the guard and your feet as shown in Fig.M.
Line Feed Button (Fig.J)
The line feed feature allows you to advance the length of
cutting line available whiletrimming.
• To extend the cutting line, fully depress the line feed
button
4
while trimming and thenrelease.
NOTE: The trimmer will stop cutting when the line feed
button is pressed and will resume cutting whenreleased.
NOTE: For maximum line length, press the button multiple
times until you hear the cutting line hitting the guard. Do not
continue to press the line feed button once the maximum
length is reached. This will result in overfeeding and will
consume stringquickly.
Speed Control Switch (Fig.J)
This string trimmer gives you the choice to operate at a
more efficient speed to extend the runtime for larger jobs, or
accelerate the trimmer speed for high‑performancecutting.
To accelerate the trimmer, push the speed control
switch
3
forward toward the auxillary handle
6
into the "HI"
position. This mode is best to cut through heavier growth
and for applications that need higherRPM.
To extend runtime, pull the speed control switch back
toward the battery housing
21
into the "LO" position. This
mode is best for larger projects that require more time
tocomplete.
NOTE: When in "HI" mode, runtime will be decreased as
compared to when trimmer is in "LO"mode.
Switching Trimmer On and Off (Fig.A)
WARNING: Never attempt to lock the
trigger in the onposition.
1. To turn the appliance on, press the lock‑off button
2
and
then squeeze the trigger
1
. Once the unit is running, you
may release the lock‑off button.
2. To turn the appliance off, release thetrigger.
Proper Hand Position (Fig.K)
WARNING: To reduce the risk of serious
personal injury, ALWAYS use proper hand position
asshown.
WARNING: To reduce the risk of serious
personal injury, ALWAYS hold securely in anticipation
of a suddenreaction.
Proper hand position requires one hand on the main
handle
5
and one hand on the auxiliary handle
6
.
Installing and Removing the Battery Pack
(Fig.I)
WARNING: Ensure the tool/appliance is in
the off position before inserting the batterypack.
NOTE: For best results, make sure your battery pack is
fullycharged.
1. To install the battery pack
12
into the tool handle, align
the battery pack with the rails inside the tool’s handle
and slide it into the handle until the battery pack is firmly
seated in the tool and ensure that it does notdisengage.
2. To remove the battery pack from the tool, press the
release button
13
and firmly pull the battery pack out of
the tool handle. Insert it into the charger as described in
the charger section of thismanual.
OPERATION
WARNING: To reduce the risk of serious
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories,
when replacing line, or prior to cleaning. An
accidental start‑up can causeinjury.
Releasing the Cutting Line (Fig.A)
In transit, the cutting line is taped to the spool housing
10
.
• Remove the tape holding the cutting line to the spoolhousing.
Attaching the Auxiliary Handle (Fig.H)
1. Remove handle knob
18
and handle bolt
19
from the
auxiliary handle
6
.
2. Push the auxiliary handle
6
onto the top of the upper
trimmer pole
8
as shown in Fig. H.
3. Thread the handle bolt
19
through the mountinghole
on the auxiliary handle
6
.
4. Thread the handle knob
18
onto the handle bolt
19
and firmly tighten. Ensure the handle is secured in
position before using.
5. To adjust the position of the auxiliary handle, loosen the
handle knob
18
and slide the auxiliary handle
6
up or
down the pole until it is in the desired location. Tighten
the handle knob
18
to secure the auxiliary handle
6
inposition.
Loading ...
Loading ...
Loading ...