Loading ...
Loading ...
Loading ...
ENGLISH
10
Installing the Guard (Fig.F, G)
WARNING: Never remove the guard.
Damage or personal injury couldresult.
WARNING: NEVER OPERATE
APPLIANCE WITHOUT GUARD FIRMLY IN PLACE.
The guard must always be properly attached on the
appliance to protect theuser.
1. Remove the guard screw
19
.
2. Slide the guard
11
fully onto the motor housing
7
.
Make sure the tabs
20
on the guard engage the ribs
16
on the trimmerhead.
3. Continue to slide the guard on until it “snaps”into place.
The locking tab
18
should snap into the housingslot
17
.
4. Using a crosshead screwdriver, insert the guard screw
19
and tightensecurely.
5. Once the guard is installed, remove the covering from the
line cut‑off blade, located on the edge of theguard.
Assembling the Pole (Fig.A, E)
1. When installing the lower pole
9
into the upper pole
8
,
align the detent lock
14
with the detent slot
15
as shown
in Fig.E.
2. Press the two poles together so the detent lock
14
engages the detent slot
15
.
3. Check to ensure the two poles are securely connected by
tugging on them and make sure the detent lock remains
engaged in the detent slot.
WARNING:
Always check to make sure
that the detent lock is completely secured in place. If the
detent lock is not completely secured it could result in the
assemblys becoming disconnected creating a hazardous
condition. Periodically check the connections to insure
that the detent lock is completely secured inplace.
ASSEMBLY AND ADJUSTMENTS
WARNING:
To reduce the risk of serious
personal injury, turn unit off and
remove the
battery pack
before making any adjustments or
removing/installing attachments or accessories,
when replacing line, or prior to cleaning. An
accidental start‑up can causeinjury.
Wall Mounting
Some CRAFTSMAN chargers are designed to be wall
mountable or to sit upright on a table or work surface. If wall
mounting, locate the charger within reach of an electrical
outlet, and away from a corner or other obstructions which
may impede air flow. Use the back of the charger as a
template for the location of the mounting screws on the wall.
Mount the charger securely using drywall screws (purchased
separately) at least 1” (25.4mm) long, with a screw head
diameter of 0.28–0.35” (7–9mm), screwed into wood to an
optimal depth leaving approximately 7/32” (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in theslots.
NOTE: Do not attempt to mount CMCB101 charger under a
bench ortable.
NOTE: Only mount CMCB101 charger with the charging
lights pointed upward toward theceiling.
VersaTrack™
WARNING: Do not charge batteries while
charger is hung onTrackwall.
CRAFTSMAN chargers, except the CMCB101, can be
stored on CRAFTSMAN VersaTrack™ Trackwall. Hooks and
accessories are sold separately. Please refer to the VersaTrack™
Trackwall accessory sheet for furtherinformation.
NOTE: The CMCB101 charger is not CRAFTSMAN VersaTrack™
Trackwallcompatible.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
battery pack in a warm environment such as in a metal
shed or an uninsulatedtrailer.
3. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
thelights;
c. If charging problems persist, take the tool, battery
pack and charger to your local servicecenter.
4. You may charge a partially used pack whenever you
desire with no adverse effect on the batterypack.
Charger Cleaning Instructions
WARNING:Shock hazard. Disconnectthe
charger from the AC outlet before cleaning. Dirt and
grease may be removed from the exterior of the charger
using a cloth or soft non‑metallic brush. Do not use
water or any cleaningsolutions.
Adjusting the Cutting Swath Size (Fig.G)
This guard allows for two swath sizes, 13 inches or 11inches.
1. To adjust the position of the cutting line blade
32
,
remove the screws
33
securing the cutting lineblade
32
in place.
2. Position the cutting line blade
32
to the second position
on the guard and secure it with the screws
33
.
NOTE: Moving the cutting line blade
32
closer to the
spool housing will decrease cutting swath size.
Loading ...
Loading ...
Loading ...