Faber CLPL36SSV2 Classica Plus Ssv2

User Manual - Page 66

For CLPL36SSV2.

PDF File Manual, 72 pages, Download pdf file

Loading ...
Loading ...
Loading ...
66
EN
7
7
INSTALLATION
Fitting the Hood canopy
BEFORE FITTING THE HOOD TO THE WALL UNIT, PROCEED AS FOLLOWS:
Disconnect the wires to the Commands at the connectors.
Disconnect the wires to the Light at the con-
nectors.
The Hood can be installed directly on the
underside of
the wall unit (Minimum 650 mm
from the Cooker Hob).
Create an opening in the bottom of the wall unit,
as shown.
Insert the hood until the side supports snap into
place.
Fasten using the 10 screws 12a provided.
Lock in position by tightening the screws Vf from
underneath the hood.
Open the suction panel by turning the specific knob.
Disconnect the panel from the hood canopy by sliding the
fixing pin lever.
Remove grease filters.
Screw the Frame into place
using the 6 scr
ews 12f, re-
connect the wires to the
Commands and Light, re-
place the metal grease filter
and the Panel.
260
13
495 - 675
CUIDADO DE LOS FILTROS
Retirar el ltro, empujando la palanca hacia la
parte posterior de la unidad mientras se tira
hacia abajo.
Lavar el ltro sin doblarlo. Dejarlo secar bien
antes de volver a colocarlo. Si la supercie del
ltro cambia de color con el tiempo, la ecacia
no se verá afectada.
Para sustituir el ltro, hay que empujar el ltro
hacia arriba en su posición mientras se man-
tiene la palanca hacia atrás, y luego soltar la
palanca para bloquearlo en su lugar.
1
2
3
EN
7
7
INSTALLATION
Fitting the Hood canopy
BEFORE FITTING THE HOOD TO THE WALL UNIT, PROCEED AS FOLLOWS:
Disconnect the wires to the Commands at the connectors.
Disconnect the wires to the Light at the con-
nectors.
The Hood can be installed directly on the
underside of
the wall unit (Minimum 650 mm
from the Cooker Hob).
Create an opening in the bottom of the wall unit,
as shown.
Insert the hood until the side supports snap into
place.
Fasten using the 10 screws 12a provided.
Lock in position by tightening the screws Vf from
underneath the hood.
Open the suction panel by turning the specific knob.
Disconnect the panel from the hood canopy by sliding the
fixing pin lever.
Remove grease filters.
Screw the Frame into place
using the 6 scr
ews 12f, re-
connect the wires to the
Commands and Light, re-
place the metal grease filter
and the Panel.
260
13
495 - 675
LIMPIEZA DE LOS FILTROS DE GRASA METÁLICOS
Los ltros de grasa metálicos pueden limpiarse en una solución de detergente
caliente o lavarse en el lavavajillas.
Deben limpiarse cada 2 meses de uso, o con mayor frecuencia si el uso es
particularmente intenso.
NOTAS:
• La limpieza en el lavavajillas puede deteriorar el acabado de los ltros de
grasa metálicos.
Asegurarse de que los ltros están completamente secos antes de volver
a instalarlos en la campana extractora.
LIMPIEZA DE LAS SUPERFICIES EXTERIORES
Por favor, tenga en cuenta que los abrasivos y los agentes de fregado pue-
den rayar los acabados de la campana extractora y no deben utilizarse para
limpiar las supercies acabadas.
Instrucciones para la limpieza del acabado de acero inoxidable:
Limpie las supercies exteriores con un limpiador de acero inoxidable dis-
ponible comercialmente.
Loading ...
Loading ...
Loading ...