Loading ...
Read Operating Instructions
Please become familiar with all the instructions and
warnings before operating any pneumatic tool,
Always Wear Approved Eye Protection
Impact resistant eye protection should meet or
exceed the standards set forth in ANSI Z87.1,
Occupational and Educational Eye and Face
Protection. Look for marking Z87. ! on your eye
protection to ensure that it is an approved style.
Hearing Protection is Recommended
Hearing protection should be used when the noise
level exposure equals or exceeds an 8 hour time-
weighted average sound level of 85dBA. Process
noise, reflective surfaces, other tools being operated
nearby, all add to the noise level in a given work area.
If you are unable to determine your noise level expo-
sure, we recommend the use of hearing protection.
Avoid Prolonged Exposure to Vibration
Pneumatic toolscan vibrate during use. Prolonged
exposure to vibration or very repetitive hand and arm
movements can cause injury. Discontinue the use of
any tool if you experience tingling, numbness, dis-
comfort or pain in your hands or arms. You should
consult your physician before resuming use of tool.
90 PSIG Maximum
This tool is designed to operate at an air pressure of
90 pounds per square inch gauge pressure (90 PSlG)
maximum, at the toot. Use of higher air pressure can,
and may cause injury. Also, the use of higher air
pressure places the internal components under loads
and stresses they were not designed for, causing
premature tool failure.
NOTE: THE AIR SUPPLY SHOULD BE CLEAN AND
DRY, PREFERABLY LUBRICATED. FOR BEST
RESULTS DRAIN THE MOISTURE FROM YOUR
COMPRESSOR DALLY.
Do Not Operate Without Guard
Always use cut-off wheels with an RPM rating that
meets or exceeds the tool RPM rating. Always
examine cut-off wheels for chips, cracks or signs of
damage before mounting. Never use cut-off wheels
that have been dropped or exposed to: water, solvent
or extreme temperatures. Itis a good practice to
operate the tool in a protected enclosure for one
minute after mounting a cut-off wheel.
FULL TWO YEAR WARRANTY ON
CRAFTSMAN AIR-DRIVE TOOLS
If this Craftsman tool fails to give complete satisfaction
within two years from the date of purchase, RETURN
IT TO THE NEAREST SEARS SERVICE CENTER/
DEPARTMENT IN THE UNITED STATES,and Sears
will repair or replace it free of cl_arge. If this Craftsman
tool is used for commercial or rental purposes, this
warranty applies for only 90 days from the date of
purchase. This warranty gives you specific legal
rights, and you may also have other rights which vary
from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman
Estates, IL 60179.
The Craftsman Model 875.199900 Pneumatic Cut-
Off Tool is designed to cut through muffler clamps
and hangers with ease, Slices sheet metal, radiator
hose clamps, rusted bumper bolts, even 3/4" thick
steel rods. Ideal for autobody work. Includes two 3"
discs,
Features
• High impact nylon handle with safety lock-off lever.
• Cuts shoe: metal, pipe and hose clamps, hangers
and rusted bolts.
• Clear Lexan guard for better visibility.
The Craftsman Pneumatic Cut-Off Tool is designed to
operate on 90 PSIG. Lower pressure (below 90 PSIG)
will reduce performance of the tool, while higher air
pressure (over 90 PSIG) raises the performance of the
tool beyond its rated capacity and could cause
serious damage to tool and user.
Before the tool is connected to the air supply, clear
the air hose of accumulated dust and moisture, and
add 1/4 oz. of air tool oi! into air tool inlet. Be sure to
lubricate tool daily for best performance.
Always use c!ean dry air, Excessive moisture and
dirt will greatly reduce the life of any air moron
We recommend the installation of an in-line
filter-regulatorqubricator as close to the tool as
possible.
(2)
Loading ...
Loading ...
Loading ...