Hoover HBRUP 170 NKE/1

Instructions Manual - Page 20

For HBRUP 170 NKE/1.

PDF File Manual, 111 pages, Read Online | Download pdf file

HBRUP 170 NKE/1 photo
Loading ...
Loading ...
Loading ...
19
The seal must adhere properly all the way around the door.
o
If the seal is not adhering to the cabinet properly, then you should either:
1.
Use a warm damp cloth and manipulate the seal until it does adhere to
the cabinet properly, all the way around the door.
Or
2.
Use a hair dryer on its lowest heat setting and lightly heat the areas of
the door seal that are not adhering correctly. The heat will make the seal
more pliable and this will allow you to manipulate the seal into the correct
position.
IMPORTANT: DO NOT HEAT THE DOOR SEAL ON ANYTHING BUT THE
LOWEST HEAT SETTING, OR HEAT THE SEAL FOR A LONG PERIOD OF TIME.
OTHERWISE DAMAGE MAY BE CAUSED TO THE DOOR SEAL, WHICH
WOULD NOT BE RECTIFIED UNDER THE GUARANTEE FREE OF CHARGE.
Aperture dimensions
The diagram below shows the aperture size that you will need to be able
to install your appliance.
o
The appliance must be stood on a level floor. You can use the levelling
feet to take into account any minor unevenness in the floor.
Adjusting the plinth/kickboard
When the appliance has been placed underneath the worktop, you may
decide to attach a plinth or kickboard to match your existing kitchen
units.
o
Remove the grid on the base of the appliance by unscrewing the
screws on each side of the grid and then pull the grid towards you.
o
Use a spanner to adjust the height of the adjustable feet.
o
If your aperture has a height of 820 mm, then the adjustable feet should
be fully tightened.
o
If your aperture has a height of 870 mm, then the adjustable feet should
be set at a height of 50 mm.
o
The appliance should be flush with the underside of the worktop and
be level.
IMPORTANT: If the appliance is not level, then the door and door seal may be
affected.
o
A cut out must be made in the plinth/kickboard for ventilation. The cut
out should measure 600mm in width, and between 140mm and 90mm in
height, depending on the height that you have set your appliance.
o
Insert the plinth/kickboard and then refit the grid in its original position
to hold it in place.
IMPORTANT: Please note that as shown in the above drawing, an
appropriately sized ventilation cut out MUST be made in the furniture
plinth/kickboard.
Fitting the furniture door to the appliance
If you need the appliance door to open from the other side, then please
reverse the door before commencing the installation process. (See “Reversing
the door section”).
Tools required:
o
Tape measure
o
Sharp pencil
o
Small flat bladed screwdriver
o
Spanner
IMPORTANT: We recommend that two people install this appliance.
1.
Undo the screws from the two adjusting bolts that are located on the top of
the appliance door and then remove the mounting bracket (1).
2.
Measure the width of the furniture door, at the halfway point mark a line
vertically down the inner surface of the furniture door. You should draw the
line from the top of the furniture door to approximately halfway down.
o
Place the mounting bracket (1) on the reverse of the furniture door.
o
The middle of the mounting bracket should be positioned on the line
that you have just drawn. Please note the position of the mounting bracket
in the above drawing, to ensure that you have the mounting bracket the
correct way up.
o
The top of the mounting bracket should be positioned approximately
15 mm from the top of the furniture door. This will allow you a 5 mm gap
from the top of the furniture door, to the underneath of your worktop.
o
Fix the mounting bracket to the furniture door using the screws
provided and a Phillips-head screwdriver. These screws should be fully
tightened.
Loading ...
Loading ...
Loading ...