L -------------3X 0.75 copper conductor
K -------------15A /110V switch
Fu------------5A fuse
M-------------Electric motor
K
6. Electrical data
10. The machine can not be cleaned by detergents; avoid using corrosive chemical
substances on machine. Do not submerge in water; wipe down exterior with moist
cloth if ne
cessary.
Instruction Book
Commercial Ice Crusher 440lbs/hr
Please read the introduction before using it
Brief Introduc�on
SKU VH309-NEW
Dimension
16.5*12.8*23.0’’
250W
110V
60Hz
2500 R/M
Power
Voltage
Frequency
Speed
This ice shaver is made of stainless steel and acrylic, so it will not rust and will last long.
Safe for use in kitchens or outdoor setups, it’s also easy to clean and maintain by wiping down
with a dry cloth a�er use. Dual-layered stainless steel keeps the device strong and sturdy.
1. R
ead all instruc�ons before opera�ng your ice shaver
1. Main parameter:
2. Before each use, wipe down your ice shaver with a clean, moist cloth
3. Che
ck voltage & ensure there are no poten�al hazards to power supply before plug
ging in.
1. 110V
2. Childr
en are forbidden to use this machine.
3. Gr
ounded socket required; keep cable away from heat; do not let the cable or electrical sockets
contact water or other liquids; do not use damaged cables, power plugs, or sockets.
4. Use only on flat surfaces to avoid damaging the internal components.
5. The ice loade
d into the hopper cannot exceed the red line 1cm deep in ice hopper
.
6. Please
only use clean cloth to scrub the ice tank; do not use water or cleaning pr
oducts.
7. Use a cle
an, dry cloth to dry the machine a�er use and prepare for storage.
8. Do not t
ouch the blade when cleaning to avoid cu�ng your finger
s.
9. Do not disman
tle the motor; when cleaning or repairing machine, first turn off the power and
r
emove from power source.
NOTE:
It is be�er to use standard sized ice cubes with s diameter of 4-5cm or smaller
DO NOT run machine without ice
1. BEFORE PLUGGING IN, open the ice hopper to wipe off the inside with a dry cloth and check
whe
ther the blade is securely installed.
3. Ope
n the hopper with the handle and add ice; do not fill past the indica�on line of the hopper
.
4. Pr
ess the power switch and lower the handle to begin shaving ice. Once ice is shaved, repea
t
pr
ocess as needed.
5. When finished, wipe down the ice shaver with a dry towel and store in a dr
y place.
2. Che
ck the power line and plug to insure the circuit is in good condi�on, then check the switch
and plug in.
5. A�en�on
4. Opera�ng instruc�ons
2. Structure of machine
3. Prepara�on
Brief Introduc�on
SKU VH309-NEW
Dimension
16.5*12.8*23.0’’
250W
110V
60Hz
2500 R/M
Power
Voltage
Frequency
Speed
This ice shaver is made of stainless steel and acrylic, so it will not rust and will last long.
Safe for use in kitchens or outdoor setups, it’s also easy to clean and maintain by wiping down
with a dry cloth a�er use. Dual-layered stainless steel keeps the device strong and sturdy.
1. R
ead all instruc�ons before opera�ng your ice shaver
1. Main parameter:
2. Before each use, wipe down your ice shaver with a clean, moist cloth
3. Che
ck voltage & ensure there are no poten�al hazards to power supply before plug
ging in.
1. 110V
2. Childr
en are forbidden to use this machine.
3. Gr
ounded socket required; keep cable away from heat; do not let the cable or electrical sockets
contact water or other liquids; do not use damaged cables, power plugs, or sockets.
4. Use only on flat surfaces to avoid damaging the internal components.
5. The ice loade
d into the hopper cannot exceed the red line 1cm deep in ice hopper
.
6. Please
only use clean cloth to scrub the ice tank; do not use water or cleaning pr
oducts.
7. Use a cle
an, dry cloth to dry the machine a�er use and prepare for storage.
8. Do not t
ouch the blade when cleaning to avoid cu�ng your finger
s.
9. Do not disman
tle the motor; when cleaning or repairing machine, first turn off the power and
r
emove from power source.
NOTE:
It is be�er to use standard sized ice cubes with s diameter of 4-5cm or smaller
DO NOT run machine without ice
1. BEFORE PLUGGING IN, open the ice hopper to wipe off the inside with a dry cloth and check
whe
ther the blade is securely installed.
3. Ope
n the hopper with the handle and add ice; do not fill past the indica�on line of the hopper
.
4. Pr
ess the power switch and lower the handle to begin shaving ice. Once ice is shaved, repea
t
pr
ocess as needed.
5. When finished, wipe down the ice shaver with a dry towel and store in a dr
y place.
2. Che
ck the power line and plug to insure the circuit is in good condi�on, then check the switch
and plug in.
5. A�en�on
4. Opera�ng instruc�ons
2. Structure of machine
3. Prepara�on
L -------------3X 0.75 copper conductor
K -------------15A /110V switch
Fu------------5A fuse
M-------------Electric motor
K
6. Electrical data
10. The machine can not be cleaned by detergents; avoid using corrosive chemical
substances on machine. Do not submerge in water; wipe down exterior with moist
cloth if ne
cessary.
Instruction Book
Commercial Ice Crusher 440lbs/hr
Please read the introduction before using it
