Loading ...
Loading ...
Loading ...
General Care & Cleaning
Cleaning the Contoured WellAreas, Burner Cap, Burner Head and Burner Drip Pans (some models)
The contou red well areas, burner cap, burner head and burner drip pans (some models) should be routinely cleaned. Keeping
the burner ports clean wilt prevent improper ignition and an uneven flame. Refer to the following instructions:
Surface
Burner
Cap
To Clean the Recessed and Contoured Areas of the Cooktop - Ifa spill occurs
on or inthe recessed or contoured areas, blot up spillwith an absorbent cloth. Rinse
with a clean, damp cloth and wipe dry.
To Remove and Replace the Surface Burner Caps and Surface Burner Heads
- Remove in the following order: (1st) surface burner grate, (2nd) surface burner
cap, (3rd) surface burner head and (4th) surface burner drip pan (if equipped).
Surface
Burner
Head
Removable
Burner
t Pan
Reverse the procedure above to replace the surface burner cap, surface burner
head and surface burner drip pans (if equipped). Do not remove any parts from
the cooktop until they have completely cooled and are safe to handle. Do not
operate the surface burners without the surface burner cap and surface
burner head properly in place.
To Clean the Surface Burner Cap, Surface Burner Head and Surface Burner
Drip Pan (if equipped) - Use a soap-filled scouring pad or a mild abrasive cleanser !_,_!"_
to clean the surface burnercaps, surface burner heads and surface burner drip pans _o
(if equipped). The ports (or slots) around the burner head must be routinely cleaned, lJ,,_
If residue still remains in these ports, use a small-gauge wire or needle to clean ....
the slots or holes. For proper flow of gas and ignition of the burner--DO NOT !_
ALLOW SPILLS, FOOD, CLEANING AGENTS OR ANY OTHER MATERIAL TO _,i_
ENTER THE GAS ORIFICE HOLDER OPENING. ALWAYS keep the surface
burner cap and surface burner head in place whenever a surface burner is in use.
Removing and Replacing the Oven Door
The door is heavy. For safe, temporary storage, lay the door flat with
the inside of the door facing down.
To Remove Oven Door:
1. Open oven door completely (horizontal with floor - See Fig. 1).
2. Remove 2 screws located on the inside of the oven door liner (See A Fig. 2)
3. Insert the 2screwsinto the door hinge holes located on the side of the hinge arm, one into
each hinge (See B Fig. 2).
4. Close oven door until the door stops, (Do not force the door to close any further). The
placement of these screws should keep door open in about a 45 degree position.
5. Grasp oven door firmly on both sides and slide door up and off hinges at the same angle.
(See Fig. 3)
6. To clean oven door, follow the instructions in the General Care & Cleaning table.
or
use
Fig. 2
about45
Hinge
To Replace Oven Door:
1. Be sure the hinge arms remain at the 45 degree angle position. Be sure the screws are
still locking the hinge arms from moving. If the screws fall out of the hinge holes, the
hinge(s) may snap back against the oven frame and could pinch fingers or chip the
porcelain finish on the oven front frame.
2. Holddoor atthe sides near thetopwhile resting the lowerfront of door onyour knee. lnsert
the door channels at the bottom of door over the door hinges, (See Fig. 3).
3. AIIowthedoortoslidedownintothedoorhingesevenlyatthesame4Sdegreeangle.The
hinge arms should be inserted into the bottom corners as far as they can go.
4. Open door completely (horizontal withfloor) and remove both screws from holes in door
hinges.
5. Reinstall the 2 screws into the door liner (See C Fig. 2).
6. Ifthe door is not in alignment with the oven frame, remove door and repeat the above steps.
Fig.3
27
Loading ...
Loading ...
Loading ...