Loading ...
Loading ...
Loading ...
English
9
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out the
lights;
c. Move the charger and battery pack to a location
where the surrounding air temperature is
approximately 65°F – 75°F (18° – 24°C);
d. If charging problems persist, take the tool, battery
pack and charger to your local servicecenter.
4. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may
also charge a partially used pack whenever you desire
with no adverse effect on the batterypack.
5. Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Always
unplug the charger from the power supply when there
is no battery pack in the cavity. Unplug the charger
before attempting toclean.
6. Do not freeze or immerse the charger in water or any
otherliquid.
Storage Recommendations
1. The best storage place is one that is cool and dry, away
from direct sunlight and excess heat orcold.
2. For long storage, it is recommended to store a fully
charged battery pack in a cool dry place out of the
charger for optimalresults.
nOTE: Battery packs should not be stored completely
depleted of charge. The battery pack will need to be
recharged beforeuse.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
COMPONENTS (FIG. A)
WARNING: Never modify the power tool or any part
of it. Damage or personal injury couldresult.
Refer to Figure A at the beginning of this manual for a
complete list ofcomponents.
Intended Use
Your cordless finish stapler has been designed for driving
staples into woodenworkpieces.
DO nOT use under wet conditions or in presence of
flammable liquids orgases.
Your cordless finish stapler is a professional powertool.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
thistool.
Tool Specifications
Firing Mode Selectable: Sequential
or Rapid Sequential
Voltage 20
Height 12.2" (30.9 cm)
Tool Specifications
Width 3.7" (9.3 cm)
Length 11.7" (29.7 cm)
Weight (without battery) 6.2 lbs (2.8 kg)
Magazine Angle Straight
Loading Capacity 100 staples
Base Adjustment Range 3/8" - 5/8" Flooring Thicknesses
Staple Specifications
Staple Lengths 1/2" - 1 1/2" (13 mm - 38 mm)
Shank Diameters 18 gauge
Staple Crown Size 1/4" (6.3 mm)
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can causeinjury.
Belt Hook (Fig. D)
WARNING: Remove staples from magazine before
making any adjustments or servicing this tool. Failure
to do so may result in seriousinjury.
WARNING: Disconnect battery pack from tool
before making any adjustments, changing
accessories, servicing, or moving the tool. Such
preventative safety measures reduce the risk of
starting the toolaccidentally.
CAUTION: When not in use, place tool on its side
on a stable surface where it will not cause a
tripping or falling hazard. Some tools with large
battery packs will stand upright on the battery pack
but may be easily knockedover.
The cordless staplers include an integrated belt hook
8
and
can be attached to either side of the tool to accommodate
left- or right-handedusers.
If the hook is not desired at all, it can be removed from
thetool.
Fig. D
8
19
To Remove Belt Hook
1. Remove battery pack fromtool.
2. To switch the tool from right- to left-hand usage simply
remove the screw
19
from the opposite side of the tool
and reassemble on the otherside.
3. Replace batterypack.
Loading ...
Loading ...
Loading ...