Loading ...
Loading ...
Loading ...
49-5000491 Rev. 3 5
REMOTE CONTROL FEATURES AND SETTINGS
Remote Control Features and Settings
10. SWING UP/DOWN
Press the SWING UP/DOWN button to choose the
position of the horizontal airflow louvers.
Status display of air flow
COOL/DRY:
HEAT:
NOTE:
• It is advisable not to keep the vertical louver in the
downward position for an extended period of time in
COOL or DRY mode. This may cause condensate
water to form on the louver.
• When turning the unit on, the remote control will
automatically return the louver to the previous set
swing position. When turning the unit off, the louver will
rotate to the full open position prior to closing.
11. SWING SIDE/SIDE Button (select models)
Press the LOUVER SIDE/SIDE button to choose the
position of the vertical airflow louvers.
Status display of air flow
COOL/DRY/HEAT/FAN
NOTE:
• When the humidity is very high, the condensate water
may occur on the air outlet if all vertical louvers are
adjusted too far to the left or right.
• When turning the unit on, the remote control will
automatically return the louver to the previous set
position.
12. DISPLAY
The indoor display panel will show indoor set
temperature by default. Press this button once, it will
display the room temperature. Press this button twice
within 3 seconds, it will turn off the indoor display
panel. Press again to go back to display indoor set
temperature.
13. SLEEP
Press the SLEEP button, the heat pump will operate the
sleep function, the display light will be turned off after 20
seconds. The control logics are as following running in
different mode.
1. COOL or DRY modes
One hour after SLEEP mode begins, the temperature
setpoint will increase 1°F (0.5°C). 2 hours after
beginning sleep mode the setpoint will increase 1°F
(0.5°C). Seven hours after beginning sleep mode,
the setpoint will decrease 1°F (0.5°C). At the eighth
hour the unit will be back to the original setpoint. This
feature helps with achieving maximum efficiency and
comfort while you sleep. See the image below.
1h
ȯ
8OYKYȯ
2h 7h 8h
In COOL, DRY mode
temp.setting
Unit stop
SLEEP operation starts
8OYKYȯ
*KIXKGYKȯ
*KIXKGYKȯ
2. Heat Mode
One hour after SLEEP mode starts, the setting
temperature will decrease 2°F. After 2 hours, the
setting temperature will decrease additional 2°F. After
5 hours, the setting temperature will increase 1°F.
After 8 hours, the unit will run according to the initial
setting temperature. This feature helps with achieving
maximum efficiency and comfort while you sleep.
1h
ȯ
2h 7h 8h
In HEAT mode
temp.setting
SLEEP operation starts
*KIXKGYKȯ
*KIXKGYKȯ
8OYKYȯ
3. AUTO mode
The unit operates in corresponding sleep mode
adapted to the automatically selected operation mode.
NOTE:
• When the unit is set to sleep mode, the fan speed
will be set to low speed and cannot be changed.
• When the TIMER function is set, the sleeping
function cannot be set. If the sleeping function has
been set and the user sets the TIMER function, the
sleeping function will be canceled and the unit will
be set to the timer function.
14. FOLLOW
Press the FOLLOW button, the air will follow the body no
matter people stand or moving. See chart below.
15. SURROUND
Press the SURROUND button. The air will surround the
body no matter whether people are standing or moving.
See chart below.
Model Detect Area Louver Up/
Down
Louver Left/
Right
FOLLOW Detect person
in single zone
Remote setting
position
Swing in the
direction of the
person
Detect person
in multi zones
Remote setting
position
Swing
automatically
Detect
nobody
Keep the initial
setting position
Keep the initial
settings position
Model Detect Area Louver Up/
Down
Louver Left/
Right
SURROUND Detect
person in
single zone
Remote
setting
position
Keep the initial
setting position
Detect
person in
multi zones
"Health airflow
(up) in cooling
mode
Health airflow
(down) in
heating mode"
Swing
automatically
Detect
nobody
Keep the
initial settings
position
Keep the
initial settings
position
Loading ...
Loading ...
Loading ...