Loading ...
Loading ...
Loading ...
– 7
Illustration
Turn the container, press in the steering roller in the
openings at the base of the container till the end-
point.
Illustration
Turn the motor casing around and attach the foam
filter to the filter basket.
Insert the filter cover and turn to lock.
Install the motor casing. Pull up on the carrying
handle to lock.
Illustration
Install the fresh water reservoir. Insert the bot-
tom part first and then press toward the top on the
motor compartment to check if it is locked in.
Illustration
Slide the spray handle onto the handle until it locks
into place.
Attach the spray hose of the spray handle to the
suction hose using 7 mounting clips.
Attach the suction hose and the spray hose to the
connectors on the appliance.
Note
: Press the suction hose tightly into the connector
to lock it into place.
Illustration
Connect the suction tubes and attach to the handle.
Insert the loose spray hose in the spray handle and
attach to the suction tubes using the 3 included
mounting clips.
Attach the floor nozzle to the suction tubes and in-
sert the spray hose into the floor nozzle. Rotate the
exterior safety lever and lock the spray hose into
place.
The appliance is now prepared for wet cleaning.
Illustration
For the installation of the spray-ex manual nozzle
the enclosed adapter must be connected and
locked between the spray-ex manual nozzle for up-
holstery cleaning and the handle.
* SE 4001 Plus
ATTENTION
Always work with an inserted foam filter - during wet
cleaning as well as wet and dry vacuum cleaning.
ATTENTION
Check the object to be cleaned prior to using the appli-
ance in an inconspicuous place for colour fastness and
water resistance.
Do not clean water-sensitive floor coverings such as
wood floors (the moisture could penetrate and damage
the floor).
Note:
Warm water (max. 50°C) will increase the cleaning ef-
fect.
With spray-ex floor nozzle without hard surface at-
tachment.
Please only use the carpet cleaner RM 519.
With spray-ex floor nozzle with hard surface attach-
ment.
Slide the attachment for hard surfaces onto the side of
the spray-ex floor nozzle. The squeegee points towards
the front, the brush strip towards the back.
Note: You can remove the water reservoir to fill it or you
can fill it directly on the appliance.
Illustration
Flip the reservoir cover up.
Add 100 - 200 ml (volume depends on degree of
contamination) of RM 519 into the fresh water res-
ervoir, then add tap water - do not overfill.
Close the reservoir cover.
Illustration
Insert the mains plug into the socket.
Press the switch for suction (position I), suction tur-
bine is running.
Illustration
Close fully the surrounding air separator at the han-
dle.
Illustration
Press the switch for spraying (position I), the deter-
gent pump is ready.
Use the lever on the spray handle to spray on de-
tergent solution.
Run across the surface to be cleaned in overlap-
ping paths. Pull the nozzle backwards (do not
push).
Note: If the container is full, a float closes the suction
opening, and the appliance works at a higher speed.
Switch off the appliance immediately, and empty the
container.
Switch the appliance off by pressing the switch for
suction and spraying (position 0).
Remove the accessories and the fresh water reser-
voir and unlatch the motor casing.
Remove the motor casing and empty the reservoir.
– Always work from the light to the shade (from the
window to the door).
– Always work from the cleaned to the uncleaned
surface.
– Rugs with jute backing can shrink if too much water
is used and can bleed colours.
– Brush high-fiber rugs in the direction of the weave
after cleaning (using a fiber brush or a scrubber).
– Water-proofing the fabric using Care Tex RM 762
after the wet cleaning prevents a quick resoiling of
the textile surface.
– Do not step on cleaned surfaces until they have
dried and do not place furniture on them to avoid
pressure spots or rust stains.
Turn on suction and spraying (position I).
Spray
and simultaneously suction off detergent so-
lution in one work cycle.
Switch off the spray switch and suction off the re-
maining cleaning solution.
After cleaning the carpets, reclean them using
clear, warm water and waterproof if needed.
Wet cleaning with the spray-ex manual nozzle for
upholstery cleaning
Operations
Wet cleaning of carpets/hard surfaces
Wet cleaning of carpeted floors
Wet cleaning of hard surfaces
8.1
8.2
Fill up fresh water reservoir
Start working
Emptying the reservoir during operation
Cleaning tips/mode of operation
Cleaning methods
Light/normal contamination
12 EN
Loading ...
Loading ...
Loading ...