Loading ...
Loading ...
Loading ...
English
7
a cloth or soft non-metallic brush. Do not use water or
any cleaningsolutions.
Important Charging Notes
1. Longest life and best performance can be obtained if
the battery pack is charged when the air temperature is
between 65°F and 75°F (18° – 24°C). DO NOT charge
the battery pack in an air temperature below +40°F
(+4.5°C), or above +104°F (+40°C). This is important
and will prevent serious damage to the batterypack.
2. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulatedtrailer.
3. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out the
lights;
c. Move the charger and battery pack to a location
where the surrounding air temperature is
approximately 65°F – 75°F (18° – 24°C);
d. If charging problems persist, take the tool, battery
pack and charger to your local servicecenter.
4. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may
also charge a partially used pack whenever you desire
with no adverse effect on the batterypack.
5. Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Always
unplug the charger from the power supply when there
is no battery pack in the cavity. Unplug the charger
before attempting toclean.
6. Do not freeze or immerse the charger in water or any
otherliquid.
Storage Recommendations
1. The best storage place is one that is cool and dry, away
from direct sunlight and excess heat orcold.
2. For long storage, it is recommended to store a fully
charged battery pack in a cool dry place out of the
charger for optimalresults.
nOTE: Battery packs should not be stored completely
depleted of charge. The battery pack will need to be
recharged beforeuse.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
COMPONENTS (FIG. A)
WARNING: Never modify the power tool or any part
of it. Damage or personal injury couldresult.
Refer to Figure A at the beginning of this manual for a
complete list ofcomponents.
INTENDED USE
This jobsite fan is designed for professionalapplications.
DO nOT use in presence of flammable liquids, gases
ordust.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
thistool.
Suspending/Mounting the Fan (Fig A, D, E)
CAUTION: When the fan hangs by the hang hooks, do
not shake the fan or the object from which it hangs. Do
not hang the fan from any electrical wires or anything
that is not secure. Personal injury or property damage
mayoccur.
CAUTION: Only use the hang hooks for hanging
the fan as shown in Fig. D. The hang hooks are not
intended to support additional weight. Do not attach
or hang anything additional to the fan or risk of
breakage may occur.
CAUTION: Do not use the hang hooks to reach with
or to support your weight in anysituation.
CAUTION: Do not stand underneath the fan when it is
mounted overhead. Serious personal injury or damage
to the fan may result if the fanfalls.
CAUTION: Do not mount the fan to theceiling.
nOTE: When using an extension cord to power the fan,
locate the fan within reach of an electrical outlet, and away
from a corner or other obstructions which may impede
airflow.
Your jobsite fan has multiple options formounting.
hang hooks
The built-in hang hooks
5
telescope out of the back legs
and can be used to suspend the fan from 2X lumber as
shown. Be sure to fully extend the hooks before using, then
rotate asneeded.
Fig. D
screw Threads (Fig. E)
Screw threads, 1/4"-20
9
and 5/8"-11
8
, are provided on
the bottom of the fan to allow mounting to atripod.
Loading ...
Loading ...
Loading ...