USER MANUAL
PORTABLE NUGGET ICE MAKER
HZB-20BN
It is important that you read these instructions before using your portable ice maker and we strongly
recommend that you keep them in a safe place for future reference.
IMPORTANT SAFETY INSTRUCTIONS…………………………………………………2
PREPARING YOUR ICE MAKER FOR USE
IMPORTANT SAFETY TIPS…………………………………………………………………….3
GETTING TO KNOW YOUR UNIT………………………………………………………
………………………………………………………..
..4
4
OPERATING PROCEDURES & MAINTENANCE
UNPACKING
UNPACKING YOUR
YOUR ICE
ICE MAKER
MAKER………………….…………………………………………...5
CONNECTING YOUR ICE MAKER……………….……….……………………………………………...5
CLEANING AND MAINTAINING YOUR ICE MAKER….………………………………………..5
USING YOUR ICE MAKER……………….……..………………………………………..6-8
TROUBLESHOOTING
TROUBLESHOOTING…………………………….…………………………………………..9
TECHNICAL PARAMETERS & CIRCUIT DIAGRAM……………………..….……….10
TECHNICAL PARAMETERS ………………………………………………………….10
CIRCUIT DIAGRAM ………………………………………………………………………..10
DISPOSAL AND WARRANTY INFORMATION…………………………………………11
TABLE OF CONTENTS
Your safety and the safety of others are very important.
We have provided many important safety messages manual and your appliance.
Always read and obey all safety messages.
This is the safety alert symbol:
!
All safety messages will follow the safety alert symbol and the word “DANGER” or “WARNING”.
These words mean:
You can be killed or seriously injured if you don’t immediate follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury,
and tell you what can happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic safety precautions should be followed to reduce the risk of fire,
electric shock, and injury to persons or property. Read all instructions before using any appliance.
Do not operate this，or any other appliance with a damaged cord.
If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a
similarly qualified person in order to avoid a hazard.
This ice-maker must be positioned so that the plug is accessible.
Connect to properly grounded outlets only. No other appliance should be plugged into the same
outlet. Be sure that the plug is fully inserted into the receptacle.
Do not run the power cord over carpeting or other heat insulators. Do not cover the cord. Keep cord
away from traffic areas, and do not submerge in water.
We do not recommend the use of an extension cord, as it may overheat and become a risk of fire. If
you must use an extension cord, use No.14AWG minimum size and rated no less than 1875 watts.
Unplug the ice maker before cleaning or making any repairs or servicing.
Exercise caution and use reasonable supervision when appliance is used near children.
Do not use your ice-maker outdoors. Place the ice-maker away from direct sunlight and make sure
that there is at least 6 inches of space between the back of your unit and wall. Keep a minimum
distance of 6 inches on each side of your unit free.
Do not use other liquid to make the ice-cube other than water.
Do not clean your ice maker with flammable fluids. The fumes can create a fire hazard or explosion.
Do not tip over.
If the ice maker is brought in from outside in wintertime, give it a few hours to warm up to room
temperature before plugging it in.
WARNING: This appliance must be earthed.
IMPORTANT:
The wires in this mains lead are colored in accordance with the following code:
Green or Green with a strip yellow: Grounding
White: Neutral
Black: Live
To avoid a hazard due to instability of the appliance, it must be placed at an even or flat surface.
PREPARING YOUR ICE MAKER FOR USE
GETTING TO KNOW YOUR UNIT
1.Ice basket
2.Top cover, removable from the top
3. Secondary water reservoir: It connects directly with the evaporator.
4. Float switch.
5. Metal shell:
6. Water drain cap: at front btm side of the unit.
7. Filter
8. Control Panel
9. Water reservoir
10. Hot Air outlet
11. MAXIMUM WATER LEVEL:——▼——
DANGER
1. Remove the exterior and interior packaging, and then check all the accessories are included. If any
parts are missing, please contact our customer service.
2. Remove all the tapes on the unit; take out the accessory parts inside.
3. Clean the interior with lukewarm water and a soft cloth.
4. Locating your ice maker on a level counter table far from direct sunlight and other sources of heat
(i.e.: stove, furnace, and radiator). Make sure that there is at least 6 inches between the back and
sides of your ice maker with the wall.
5. Allow one hour for the refrigerant fluid to settle down before plugging your ice maker in.
6. The power plug must be accessible directly.
WARNING: fill with potable water only. Only use drinking water.
*Improper use of the grounded plug can result in the risk of electrical shock. If the power cord
is damaged, please call our customer service.
1. This unit should be properly grounded for your safety. The power cord of this appliance is equipped
with a grounding plug which mates with standard grounding wall outlets to minimize the possibility of
electric shock.
2. Plug your appliance into an exclusive, properly installed, grounding wall outlet. Do not under any
circumstances; damage the grounding means of the plug. Any questions concerning power and/or
grounding should be directed toward a certified electrician.
3. This appliance requires a standard 110-120Volt, 60Hz electrical outlet with good grounding means.
Before using your ice maker, it is strongly recommended to clean it thoroughly.
Unplug the unit before cleaning or making any maintenance.
1. Take out the ice basket.
2. Clean the interior with diluted detergent, warm water and a soft cloth.
3. Then use the water to rinse the inside parts, and drain out the water by unplugging the drain cap on
front bottom side.
4. The outside of the ice maker should be cleaned regularly with a mild detergent solution and warm
water.
5. Dry the interior and exterior with a clean soft cloth.
6. When the machine is not to be used for a long time, drain water completely & dry the interior.
OPERATING PROCEDURES & MAINTENANCE
How to start the unit
1. Take out the ice basket, pour potable water into water reservoir, 0.58 gallon (2.2 liters) water at most
at one time.
2. Put back the ice basket.
3. Plug in the power cord.
Operation and display areas
Plug in the power cord, the screen is on: you can operate this appliance by touch the button on
panel as shown above, the main function includes: ice, clean and timer.
USING YOUR ICE MAKER
CLEAN
For the first time, or the clean procedure has not been running for a long time, it is highly
recommended to run this procedure at first.
4. Before clean procedure, please make sure the water drain cap has been inserted into the appliance;
otherwise it will not work properly.
5. Press “ICE/CLEAN” button “ ” for 5 seconds, the screen displays 20M and the “CLEAN” symbol
“ ”(as shown in the figure below), it will run cleaning procedure for 20 minutes and automatically
exit, press this button again during the cleaning procedure, it will exit immediately.
6. After cleaning procedure, remove the top cover and the ice basket, rinse the main water reservoir
and the secondary water reservoir, then move the appliance to the edge of the desktop, make sure
that the appliance is placed steady, place a water container under the appliance,remove drain cap
from the bottom, dirty water will drain into the water container, then reinsert the drain cap.
Change water in the water reservoir every 24 hours to ensure a reasonable hygiene level. If the unit
isn’t to be used, drain all water & dry the water reservoir.
How to obtain the ice-cube
7. Before we start making ice, please make sure the water drain cap has been inserted into the
appliance; otherwise it will not work properly.
8. Press “ICE/CLEAN” button “ ”, the screen displays “ICE” symbol “ ” (as shown in the figure
below) , it begin to work, Press this button again, it will stop making ice.
9. For the first time, or if the appliance has not been used for a long time, it is recommended to clean
this appliance before you start to make ice.
10. While the ice-maker is on, verify water level periodically. If water pump can’t pump out water, the ice
maker will stop automatically, and the “Add water” symbol “ ” will appear (as shown in the figure
below). Need to pour water into the water reservoir inside.
11. The ice maker automatically stops working when the ice-cube is full inside and the “ice full” symbol
“ ” appears(as shown in the figure below).
How to set the timer
Timer Delay Time Range: 0-24 hours
Press once to change: 1H
When the unit is running, you can set the unit with OFF-TIMER to let the unit stop running after your
set delay time.
And when the unit is on standby, you can set the unit with ON-TIMER to let the unit start to run
automatically after your set delay time, then when you go back home or have a dinner, you can enjoy the
happy life that this ice-maker give to you.
12. Press the “TIMER” button “▲” or “▼” to start setting timing, then press the “▲” button to increase the
time, and press the “▼” button to decrease the time. Press the “TIMER” button in standby mode, it
will startup after the countdown (as shown in the figure a); Press the “TIMER” button in Ice-making
mode, it will shutdown after the countdown (as shown in the figure b).
a. (Start ice making in three hours) b.(Exit ice making after three hours)
13. When the unit has been set with the timer, press the TIMER button, then the delay time digit and “H”
letter display will disappear, mean the timer set has been canceled.
Tips: The background light on the screen automatically goes out after 30 seconds without operation, if
you want to keep the light on, press the “TIMER” button “▲” for 5 seconds; And if you want to cancel the
constant light, press the “TIMER” button “▲” for 5 seconds again.
Timer delay time
Means Hour, and timer setting duration
PROBLEM
POSSIBLE CAUSE
SOLUTION
“” symbol is
lightening on and
the arrow flashes.
Lack of Water.
Stop the ice maker, fill water, and
press “ICE/CLEAN” button again
to restart the unit.
“ ” symbol is
lightening and
letter “F” flashes.
There is too much ice.
Suggest you to obtain the
ice-cube.
(No ice cube inside).
Remove the probable obstacle
inside or clean the inside wall of
the ice storage
Press “ICE/CLEAN” button for 5
seconds ，it will work for 80
minutes.
E1
Ambient temperature or water
temperature in inner tank is too high.
Please run the ice maker below
90 Fahrenheit degree ambient
and pour colder water into tank.
Refrigerant liquid leakage.
Press the ICE button twice, restart
ice making program, if this
problem show up again, verify
by a qualified technician.
Cover motor is broken
Pipe in the cooling system is
blocked.
Making Ice too
slowly
Hot Air outlet has been blocked by
something.
Hot Air outlet must be guaranteed
to have more than 15 CM of
ventilation distance.
Water temperature in inner tank is
too high.
Water temperature requirement
between 7℃-32℃.
Refrigeration system malfunctions.
Verify by a qualified technician.
Water leakage
Drain plug not in place
Put the drain plug in place.
Pipe Joint in the appliance may
Loose
Verify by a qualified technician.
The seal has reached service life
Verify by a qualified technician.
TROUBLESHOOTING
·
Model
Model HZB-
HZB-20
20B
BN
N
Protection
Protection Type
Type I
I
Power
Power 115
115V/
V/6
60Hz
0Hz
Ice
Ice Making
Making Current
Current 2.
2.6
6A
A
Refrigerant
Refrigerant R
R600
600a
a/
/23g
23g
Vesicant
Vesicant C
C5
5H
H10
10
Net
Net Weight
Weight 1
13
3.5Kg
.5Kg
Dimension
Dimension 2
240x335x390
40x335x390mm
mm
TECHNICAL PARAMETERS
CIRCUIT DIAGRAM
TECHNICAL PARAMETERS & CIRCUIT
10
Disposal
When the unit is not to be used again, disposal of this unit’s material shall be in accordance
with national regulations.
Warranty Information
The manufacturer provides warranty in accordance with the legislation of the customer's own
country of residence, with a minimum of 1 year, starting from the date on which the appliance is
sold to the end user.
The warranty only covers defects in material or workmanship.
The repairs under warranty may only be carried out by an authorized service technician. When
making a claim under the warranty, the original bill of purchase (with purchase date) must be
submitted.
The warranty will not apply in cases of:
- Normal wear and tear
- Incorrect use, e.g. overloading of the appliance, use of non-approved accessories
- Use of force, damage caused by external influences
- Damage caused by non-observance of the user manual, e.g. connection to an unsuitable
mains supply or non-compliance with the installation instructions
- Partially or completely dismantled appliances
Disposal and Warranty Information
