Loading ...
Loading ...
Loading ...
13
ENGLISH
Helpful Hints
• Always ensure the workpiece is firmly held or clamped to
prevent movement. Any movement of the material may
affect the quality of the cutting or sandingfinish.
Using the Dust Extraction Adaptor with
Plunge Cutting Accessory (Fig. S)
Optional Accessory
1. Attach the dust extraction adaptor. Refer to Attaching
the Dust ExtractionAdaptor.
2. Push dust extraction arm
20
into the lower aperture of
the dust extraction adaptor
18
.
3. Attach plunge cutting blade as described under
Installing/RemovingAccessories.
4. Adjust the dust extraction arm
20
for bestresults.
Using the Dust Extraction Adaptor with
the Sanding Platen (Fig. R)
Optional Accessory
1. Attach the dust extraction adaptor
18
. Refer to
Attaching the Dust ExtractionAdaptor.
2. Attach the sanding platen
23
as described under
Installing/RemovingAccessories.
3. Attach sanding sheet as described under Installing/
Removing SandingSheets.
LED Worklight (Fig. O)
The LED worklight
2
will activate when the trigger is
depressed. It will automatically shut off following a short
period of time once the trigger isreleased.
Lock on/off Button (Fig. N)
The tool can be locked off by fully depressing the lock on/off
button
4
to the left until it "clicks" as shown in Figure N.
Pushing the lock on/off button
4
to the left with the
trigger
1
depressed will lock the trigger in the depressed
position. This allows for more comfort and control in
extended useapplications.
Pressing the trigger switch again will release the lock out and
the tool will turn off upon release of thetrigger.
NOTE: The tool will automatically shut off after operating
for five minutes with the lock-on button engaged. To restart
the tool, the user will have to release the trigger and repress
lock-onbutton.
Instructions for Use (Fig. A)
1. Install the batterypack.
2. To turn the tool ON, hold it as shown in FigureM and
press the variable speed trigger
1
.
NOTE: The further the trigger switch is depressed the
faster the tool will operate. If in doubt about the proper
speed for your operation, test the performance at low
speed and gradually increase until a comfortable speed
isfound.
3. To turn the tool OFF, release the variable speed
trigger
1
.
Installing and Removing the Battery Pack
(Fig. D)
WARNING: Ensure the switch is in the off position
before inserting batterypack.
NOTE: For best results, make sure your battery pack is
fullycharged.
To install the battery pack
8
into the tool handle, align the
battery pack with the rails inside the tool’s handle and slide
it into the handle until the battery pack is firmly seated in the
tool and ensure that it does notdisengage.
To remove the battery pack from the tool, press the release
button
9
and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of thismanual.
Proper Hand Position (Fig. M)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
suddenreaction.
Proper hand position requires one hand on the main
handle
10
.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can causeinjury.
during use. DO NOT suspend tool overhead or suspend
objects from the belthook.
WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook
issecure.
IMPORTANT: When attaching or replacing the belt hook,
only use the screw
26
that is provided with the belt hook.
Be sure to securely tighten thescrew.
To accommodate left- or right- handed users the belt
hook
25
can be attached to the tool using one of the
slots below the main handle on left or right side and using
the provided screw
26
installed on the underside of the
mainhandle.
If the belt hook is not desired at all, it can be removed from
thetool.
To Install the Belt Hook
1. Insert the hook into one of the slots, on left or right side,
below the mainhandle.
2. Install the screw on the underside of the mainhandle. Be
sure to securely tighten thescrew.
To Remove or Move the Belt Hook
1. Remove the screw located on the underside of the
mainhandle.
2. Pull the belt hook away from the mainhandle.
3. Insert the hook into one of the slots, on left or right
side, below the main handle, or install the screw on the
underside of the mainhandle. Be sure to securely tighten
thescrew.
Loading ...
Loading ...
Loading ...