KitchenAid KIF 5O41 PLETGS UK FULLY INTEGRATED DISHWASHER

User Manual - Page 10

For KIF 5O41 PLETGS UK.

PDF File Manual, 20 pages, Read Online | Download pdf file

KIF 5O41 PLETGS UK photo
Loading ...
Loading ...
Loading ...
10
SELECTING A CYCLE AND OPTIONS
POWER
CLEAN
50° 3:10h
DYNAMIC
CLEAN
50° 3:10h
MODIFYING A RUNNING PROGRAM
If a wrong program was selected, it is possible to change it, provided
that it has only just begun: open the door, press and hold the „ON/OFF”
button, the machine will switch o.
Switch the machine back on using the „ON/OFF” button and
select the new wash cycle and any desired options; start the cycle
by pressing the „START button and closing the door within 4
sec.
TO PAUSE THE CYCLE (ADDING EXTRA ITEMS)
Open the door and place the crockery inside the dishwasher,
(beware of HOT steam!). Press „START button and close the
door within 4 sec. to resume the cycle from the point at which it was
interrupted.
ACCIDENTAL INTERRUPTIONS
If the door is opened during the wash cycle, or if there is a power
cut, the cycle stops. To resume the cycle from where it was interrup-
ted, press the „START button and close the door within 4 sec.
Open appliance door (beware of hot steam!) and unload the racks,
starting from the lower rack rst.
If it is needed to rell salt reservoir or rinse aid dispenser, it is
recommended to do this operations right before start of the next
cycle.
ECO CYCLE
1 2 3
45
NORMALLY SOILED CROCKERY.
STANDARD PROGRAM,
WATER ENERGY
The list of available cycles and options can be found in Cycle Table
on next page. Eco cycle is selected by default. If you want to have Last
Used cycle selected by default, you can change it in „Settings Menu”.
It is possible to select a cycle by pressing 1 of 6 cycles direct access
buttons or by pressing „Extra Cycles button repeatedly. When the
last one is reached a further press goes back to the rst.
Press cycle button to choose cycle in accordance with the level
of soiling of the dishes and with Cycle Table. Information will be
shown on the display:
1. Indicators
2. Name of the selected cycle
3. Vertical bar showing the position of the extra cycle list only
4. Energy consumption of the selected cycle
5. Water consumption of the selected cycle
Three seconds after selecting a cycle, its
time and temperature will be displayed
(if available).
Press „INFO” button to display a brief description of the cycle and
its water / energy consumption.
During the selection phase the „START LED blinks.
Additional options are available for most cycles (see „Options and
Settings” section). When any option is selected, its name is shown on
the display on the right.
If more than one option is selected one
bullet point for each option is displayed.
Each option name is displayed for 3 sec.
with its bullet point fulled.
When the cycle and option selection is complete, press „START
button and close the door within 4 seconds to start chosen cycle.
After the cycle nishes, there is an acustic signal and the dispaly shows:
On the display additional information can be shown:
ADD SALT - rell salt reservoir.
ADD RINSE AID - rell rinse aid.
DEGREASE AND CLEAN MACHINE WE RECOMMEND WPRO - every 50 cycle, will be
recommended to use the WPRO cleaner (according to instruction
on the consumable).
After 10 minutes the appliance switches o.
WATER SOFTENING SYSTEM
Water softener automatically reduces water hardness, consequently
preventing scale buildup on heater, contributing also to better cleaning
eciency.
This system regenerates itself with salt, therefore it is required to
rell salt container when empty.
Frequency of regeneration depends on water hardness level setting -
regeneration takes place once per 6 Eco cycles with water hardness
level set to 3.
Regeneration process starts in nal rinse and nishes in drying phase,
before cycle ends.
Single regeneration consumes: ~3.5L of water;
Takes up to 5 additional minutes for the cycle;
Consumes below 0.005kWh of energy.
CYCLE FINISHED
Loading ...
Loading ...
Loading ...