IRS335SDHM00 Ikea side-by-side refrigerator

User Manual - Page 9

For IRS335SDHM00.

PDF File Manual, 27 pages, Download pdf file

Loading ...
Loading ...
Loading ...
9
IMPORTANT:
Make sur
e it is a cold water pipe.
Horizontal pipe will work, but drill on the topside of the pipe,
not the bottom. This will help keep water away fr
om the drill
and normal sediment from collecting in the valve.
4.
Determine the length of copper tubing you need. Measure
fr
om the connection on the lower rear corner of refrigerator to
the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use
1/4" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure
both ends of copper tubing are cut square.
5.
Using a cordless drill, drill a 1/4" (6.35 mm) hole in the cold
water pipe you have selected.
A
B
C
DEF
G
6. Fasten the shut-off valve to the cold water pipe with the pipe
clamp. Be sur
e the outlet end is solidly in the 1/4" (6.35 mm)
drilled hole in the water pipe and that the washer is under the
pipe clamp. Tighten the packing nut. Tighten the pipe clamp
screws slowly and evenly so the washer makes a watertight
seal. Do not overtighten, or you may crush the copper tubing.
7.
Slip the compr
ession sleeve and compression nut on
the copper tubing as shown. Insert the end of the tubing
into the outlet end squarely as far as it will go. Screw the
compression nut onto outlet end with adjustable wrench. Do
not overtighten.
8.
Place
the free end of the tubing in a container or sink, and turn
on the main water supply. Flush the tubing until water is clear.
Turn off the shut-off valve on the water pipe. Coil the copper
tubing.
Connect to Refrigerator
Style 1
1.
Unplug r
efrigerator or disconnect power.
2.
Remove and discar
d the short, black plastic part from the end
of the water line inlet.
3.
Thread the nut onto the end of the tubing. Tighten the nut by
hand. Then tighten it with a wr
ench two more turns. Do not
overtighten.
NOTE: To avoid rattling, be sure the copper tubing does not
touch the cabinet’s side wall or other parts inside the cabinet.
A B C
D
A. Household water line
B. Nut (purchased)
C. Ferrule (purchased)
D. Refrigerator water tubing
4. Install the water supply tube clamp around the water supply
line to reduce strain on the coupling.
5.
T
urn shut-off valve on.
6.
Check for leaks. Tighten any connections (including
connections at the valve) or nuts that leak.
Style 2
1.
Unplug r
efrigerator or disconnect power.
2.
Remove and discard the plastic part that is attached to the
inlet of the water valve.
3.
Attach the copper tube to the valve inlet using a compression
nut and sleeve as shown. Tighten the compression nut. Do
not overtighten.
4.
Use the tube clamp on the back of the r
efrigerator to secure
the tubing to the refrigerator as shown. This will help avoid
damage to the tubing when the refrigerator is pushed back
against the wall.
5.
T
urn shut-off valve on.
6.
Check for leaks. Tighten any connections (including
connections at the valve) or nuts that leak.
A
C
B
D
E
7. On some models, the ice maker is equipped with a built-in
water strainer
. If your water conditions require a second water
strainer, install it in the 1/4" (6.35 mm) water line at either
tube connection. Obtain a water strainer from your nearest
appliance dealer.
Style 3
1.
Unplug r
efrigerator or disconnect power.
2.
Remove and discard the black nylon plug from the gray water
tube on the rear of the refrigerator.
3.
If the gray water tube supplied with the refrigerator is not
long enough, a 1/4" x 1/4" (6.35 mm x 6.35 mm) coupling is
needed in order to connect the water tubing to an existing
household water line. Thr
ead the provided nut onto the
coupling on the end of the copper tubing.
NOTE: Tighten the nut by hand. Then tighten it with a wrench
two more turns. Do not overtighten.
A B C D E F G
4. T
urn shut-off valve on.
5.
Check for leaks. Tighten any nuts or connections (including
connections at the valve) that leak.
A. Cold water pipe
B. Pipe clamp
C. Copper tubing
D. Compression nut
E. Compression
sleeve
F. Shut-off valve
G. Packing nut
A. Tube clamp
B. Tube clamp screw
C. Copper tubing
D. Compression nut
E. Valve nut
A. Refrigerator water tubing
B. Nut (provided)
C. Bulb
D. Coupling (purchased)
E. Ferrule (purchased)
F. Nut (purchased)
G. Household water line
Loading ...
Loading ...
Loading ...