Rotator
®
with PowerFins
®
HairPro
™
and Odor Neutralizer
Technology Upright Vacuum
ZU100 Series
OWNER’S GUIDE
sharkclean.comsharkclean.com
READ ALL INSTRUCTIONS BEFORE
USING THIS VACUUM
1. Inspect power cord and plug for any
damage before use. DO NOT use
vacuum cleaner with a damaged cord
or plug. Turn off all controls before
plugging in or unplugging the vacuum
cleaner. Store your vacuum cleaner
with the power cord secured around
the two cord hooks. To minimize
the risk of power cord damage, do
not allow the motorized brush roll
to ingest the cord. If this occurs,
immediately shut off power to the
vacuum and remove the cord.
2. This appliance has a polarized plug.
If the plug does not fit fully into the
outlet, reverse the plug (one blade is
wider than the other). If it still does
not fit, contact a qualified electrician.
DO NOT force into outlet or try to
modify to fit.
3. Your vacuum cleaner may consist of
a motorized nozzle, wand, hose, and/
or vacuum pod. This device contains
electrical connections, electrical
wiring, and moving parts that
potentially present risk to the user.
The hose contains electrical wires.
Do not use when damaged, cut, or
punctured.
4. Use only identical replacement parts.
5. Carefully observe and follow the
instructions provided below to avoid
improper use of the appliance.
DO NOT use the vacuum for any
purpose other than those described in
this manual.
6. Before use, carefully inspect all parts
for any damage. DO NOT use if any
parts are damaged.
7. The use of an extension cord is
NOT recommended.
8. This vacuum cleaner contains
no serviceable parts.
9. This appliance can be used by
persons with reduced physical,
sensory, or mental capabilities or
lack of experience and knowledge
if they have been given supervision
or instruction concerning use of
the appliance in a safe way and
understand the hazards involved.
Cleaning and user maintenance shall
not be made by children. Keep the
appliance and its cord out of reach of
children. DO NOT allow the appliance
to be used by children. DO NOT allow
to be used as a toy. Close supervision
is necessary when used near children.
10. Always turn off the vacuum cleaner
before connecting or disconnecting
any motorized nozzles, hose, or other
accessories.
11. DO NOT handle plug or vacuum
cleaner with wet hands.
12. DO NOT use without filters in place.
13. Only use Shark® branded filters
and accessories.
14. DO NOT damage the power cord:
a) DO NOT pull or carry vacuum
cleaner by the cord or use the cord
as a handle.
b) DO NOT unplug by pulling on cord.
Grasp the plug, not the cord.
c) DO NOT run the vacuum cleaner
over the power cord, close a door
on the cord, pull the cord around
sharp corners, or leave the cord
near heated surfaces.
15. DO NOT put any objects into nozzle
or accessory openings. DO NOT use
with any opening blocked; keep free
of dust, lint, hair, and anything that
may reduce airflow.
16. DO NOT use if nozzle or accessory
airflow is restricted. If the air paths or
the motorized floor nozzle become
blocked, turn the vacuum cleaner
off and unplug from electrical outlet.
Remove all obstructions before you
plug in and turn on the unit again.
17. Keep nozzle and all vacuum openings
away from hair, face, fingers,
uncovered feet, or loose clothing.
18. DO NOT use if vacuum cleaner is
not working as it should, or has been
dropped, damaged, left outdoors, or
dropped into water.
19. Use extra care when cleaning on stairs.
20. DO NOT leave the vacuum cleaner
unattended while plugged in.
21. When powered on, keep the vacuum
cleaner moving over the carpet
surface at all times to avoid damaging
the carpet fibers.
22. DO NOT place vacuum cleaner on
unstable surfaces such as chairs
or tables.
23. Your Shark® vacuum may not
be designed to stand up on its own.
When taking a break from cleaning,
you may need to lean it against
furniture or a wall, or lay it flat
on the floor. Using the vacuum
for an application where the unit lacks
stability may result in personal injury.
24. DO NOT use to pick up:
a) Liquids
b) Large objects
c) Hard or sharp objects
(glass, nails, screws, or coins)
d) Large quantities of dust (drywall
dust, fireplace ash, or embers).
DO NOT use as an attachment to
power tools for dust collection.
e) Smoking or burning objects
(hot coals, cigarette butts,
or matches)
f) Flammable or combustible
materials (lighter fluid, gasoline, or
kerosene)
g) Toxic materials (chlorine bleach,
ammonia, or drain cleaner)
25. DO NOT use in the following areas:
a) Poorly lit areas
b) Wet or damp surfaces
c) Outdoor areas
d) Spaces that are enclosed and may
contain explosive or toxic fumes
or vapors (lighter fluid, gasoline,
kerosene, paint, paint thinners,
mothproofing substances, or
flammable dust).
26. Turn off all controls before plugging in
or unplugging the vacuum.
ODOR
27. Observe the following when
interacting with the odor neutralizer
technology cartridge
a) DO NOT attempt to disassemble
odor neutralizer technology
cartridge.
b) Avoid direct contact with the
fragrance pod in the cartridge.
c) DO NOT directly inhale from
the odor neutralizer technology
cartridge
d) Keep away from children and pets.
e) Keep away from heat, sparks, and
open flame.
f) DO NOT place in direct sunlight.
FRAGRANCE CARTRIDGE FIRST AID
a) Avoid contact with fabrics and
finished surfaces.
b) Eye contact: Remove contact lenses
if present. Rinse continuously with
water for several minutes.
c) Skin contact: Wash hands
thoroughly after handling. If
irritation or rash develops, seek
medical advice/attention.
d) Inhalation: Move person to fresh air
if they are experiencing any
respiratory symptoms. If symptoms
persist, seek medical advice/
attention.
e) Ingestion: DO NOT induce
vomiting. Seek medical advice/
attention.
28. Unplug from electrical outlet when not
in use and before any maintenance or
cleaning.
29. Hand wash with water only.
Washing with cleaning chemicals
could damage the unit.
30. During cleaning or routine
maintenance, DO NOT cut anything
other than hair, fibers, or string
wrapped around the brushroll.
31. Allow all filters to air-dry completely
before replacing in the vacuum to
prevent liquid from being drawn into
electric parts.
32. Make sure the dust cup and all filters
are in place after routine maintenance.
33. If provided, secure the power
cord around the two cord hooks
during storage.
WARNING
To reduce the risk of fire, electric shock, injury, or property damage, when using
an electrical appliance, basic precautions should always be followed, including
the following:
IMPORTANT SAFETY INSTRUCTIONS
FOR HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS
sharkclean.comsharkclean.com
READ ALL INSTRUCTIONS BEFORE
USING THIS VACUUM
1. Inspect power cord and plug for any
damage before use. DO NOT use
vacuum cleaner with a damaged cord
or plug. Turn off all controls before
plugging in or unplugging the vacuum
cleaner. Store your vacuum cleaner
with the power cord secured around
the two cord hooks. To minimize
the risk of power cord damage, do
not allow the motorized brush roll
to ingest the cord. If this occurs,
immediately shut off power to the
vacuum and remove the cord.
2. This appliance has a polarized plug.
If the plug does not fit fully into the
outlet, reverse the plug (one blade is
wider than the other). If it still does
not fit, contact a qualified electrician.
DO NOT force into outlet or try to
modify to fit.
3. Your vacuum cleaner may consist of
a motorized nozzle, wand, hose, and/
or vacuum pod. This device contains
electrical connections, electrical
wiring, and moving parts that
potentially present risk to the user.
The hose contains electrical wires.
Do not use when damaged, cut, or
punctured.
4. Use only identical replacement parts.
5. Carefully observe and follow the
instructions provided below to avoid
improper use of the appliance.
DO NOT use the vacuum for any
purpose other than those described in
this manual.
6. Before use, carefully inspect all parts
for any damage. DO NOT use if any
parts are damaged.
7. The use of an extension cord is
NOT recommended.
8. This vacuum cleaner contains
no serviceable parts.
9. This appliance can be used by
persons with reduced physical,
sensory, or mental capabilities or
lack of experience and knowledge
if they have been given supervision
or instruction concerning use of
the appliance in a safe way and
understand the hazards involved.
Cleaning and user maintenance shall
not be made by children. Keep the
appliance and its cord out of reach of
children. DO NOT allow the appliance
to be used by children. DO NOT allow
to be used as a toy. Close supervision
is necessary when used near children.
10. Always turn off the vacuum cleaner
before connecting or disconnecting
any motorized nozzles, hose, or other
accessories.
11. DO NOT handle plug or vacuum
cleaner with wet hands.
12. DO NOT use without filters in place.
13. Only use Shark® branded filters
and accessories.
14. DO NOT damage the power cord:
a) DO NOT pull or carry vacuum
cleaner by the cord or use the cord
as a handle.
b) DO NOT unplug by pulling on cord.
Grasp the plug, not the cord.
c) DO NOT run the vacuum cleaner
over the power cord, close a door
on the cord, pull the cord around
sharp corners, or leave the cord
near heated surfaces.
15. DO NOT put any objects into nozzle
or accessory openings. DO NOT use
with any opening blocked; keep free
of dust, lint, hair, and anything that
may reduce airflow.
16. DO NOT use if nozzle or accessory
airflow is restricted. If the air paths or
the motorized floor nozzle become
blocked, turn the vacuum cleaner
off and unplug from electrical outlet.
Remove all obstructions before you
plug in and turn on the unit again.
17. Keep nozzle and all vacuum openings
away from hair, face, fingers,
uncovered feet, or loose clothing.
18. DO NOT use if vacuum cleaner is
not working as it should, or has been
dropped, damaged, left outdoors, or
dropped into water.
19. Use extra care when cleaning on stairs.
20. DO NOT leave the vacuum cleaner
unattended while plugged in.
21. When powered on, keep the vacuum
cleaner moving over the carpet
surface at all times to avoid damaging
the carpet fibers.
22. DO NOT place vacuum cleaner on
unstable surfaces such as chairs
or tables.
23. Your Shark® vacuum may not
be designed to stand up on its own.
When taking a break from cleaning,
you may need to lean it against
furniture or a wall, or lay it flat
on the floor. Using the vacuum
for an application where the unit lacks
stability may result in personal injury.
24. DO NOT use to pick up:
a) Liquids
b) Large objects
c) Hard or sharp objects
(glass, nails, screws, or coins)
d) Large quantities of dust (drywall
dust, fireplace ash, or embers).
DO NOT use as an attachment to
power tools for dust collection.
e) Smoking or burning objects
(hot coals, cigarette butts,
or matches)
f) Flammable or combustible
materials (lighter fluid, gasoline, or
kerosene)
g) Toxic materials (chlorine bleach,
ammonia, or drain cleaner)
25. DO NOT use in the following areas:
a) Poorly lit areas
b) Wet or damp surfaces
c) Outdoor areas
d) Spaces that are enclosed and may
contain explosive or toxic fumes
or vapors (lighter fluid, gasoline,
kerosene, paint, paint thinners,
mothproofing substances, or
flammable dust).
26. Turn off all controls before plugging in
or unplugging the vacuum.
ODOR
27. Observe the following when
interacting with the odor neutralizer
technology cartridge
a) DO NOT attempt to disassemble
odor neutralizer technology
cartridge.
b) Avoid direct contact with the
fragrance pod in the cartridge.
c) DO NOT directly inhale from
the odor neutralizer technology
cartridge
d) Keep away from children and pets.
e) Keep away from heat, sparks, and
open flame.
f) DO NOT place in direct sunlight.
FRAGRANCE CARTRIDGE FIRST AID
a) Avoid contact with fabrics and
finished surfaces.
b) Eye contact: Remove contact lenses
if present. Rinse continuously with
water for several minutes.
c) Skin contact: Wash hands
thoroughly after handling. If
irritation or rash develops, seek
medical advice/attention.
d) Inhalation: Move person to fresh air
if they are experiencing any
respiratory symptoms. If symptoms
persist, seek medical advice/
attention.
e) Ingestion: DO NOT induce
vomiting. Seek medical advice/
attention.
28. Unplug from electrical outlet when not
in use and before any maintenance or
cleaning.
29. Hand wash with water only.
Washing with cleaning chemicals
could damage the unit.
30. During cleaning or routine
maintenance, DO NOT cut anything
other than hair, fibers, or string
wrapped around the brushroll.
31. Allow all filters to air-dry completely
before replacing in the vacuum to
prevent liquid from being drawn into
electric parts.
32. Make sure the dust cup and all filters
are in place after routine maintenance.
33. If provided, secure the power
cord around the two cord hooks
during storage.
WARNING
To reduce the risk of fire, electric shock, injury, or property damage, when using
an electrical appliance, basic precautions should always be followed, including
the following:
IMPORTANT SAFETY INSTRUCTIONS
FOR HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS
sharkclean.comsharkclean.com
ASSEMBLY ASSEMBLY
1. Insert Wand into Pod.
2. Insert Handle into wand.
3. Attach Hose to back of pod.
4. Attach hose to Clip on wand.
5. Insert Hose Clip onto base of pod and remove tape.
6. Store Accessories on tool storage posts.
7. Remove Odor Neutralizer Technology Dial from bag. Flip up the dial handle, align the teal
arrows, then insert the dial into the nozzle.
8. To lock and engage the dial, rotate it counterclockwise until it clicks into the desired
odor intensity setting.
* More detailed odor neutralizer technology assembly instructions and visuals on the following
two pages.
IMPORTANT: For proper operation, ensure all connections are securely clicked into place.
(Click)
1
(Click)
2
6
Tool Storage Posts
Upper Cord
Hook
Cord Clip
POWER CORD
For cord access, rotate upper
hook down and remove cord.
Use cord clip located on the side of wand
to hold cord in place while vacuuming.
UPPER CORD HOOK CORD CLIP
(Click)
3
(Click)
5
(Click)
4
(Turn to
Click)
8
7
sharkclean.comsharkclean.com
ASSEMBLY ASSEMBLY
1. Insert Wand into Pod.
2. Insert Handle into wand.
3. Attach Hose to back of pod.
4. Attach hose to Clip on wand.
5. Insert Hose Clip onto base of pod and remove tape.
6. Store Accessories on tool storage posts.
7. Remove Odor Neutralizer Technology Dial from bag. Flip up the dial handle, align the teal
arrows, then insert the dial into the nozzle.
8. To lock and engage the dial, rotate it counterclockwise until it clicks into the desired
odor intensity setting.
* More detailed odor neutralizer technology assembly instructions and visuals on the following
two pages.
IMPORTANT: For proper operation, ensure all connections are securely clicked into place.
(Click)
1
(Click)
2
6
Tool Storage Posts
Upper Cord
Hook
Cord Clip
POWER CORD
For cord access, rotate upper
hook down and remove cord.
Use cord clip located on the side of wand
to hold cord in place while vacuuming.
UPPER CORD HOOK CORD CLIP
(Click)
3
(Click)
5
(Click)
4
(Turn to
Click)
8
7
sharkclean.comsharkclean.com
ODOR NEUTRALIZER TECHNOLOGY
ODOR CARTRIDGE REPLACEMENT
TECHNOLOGY SETTINGS
ODOR NEUTRALIZER TECHNOLOGY TIPS
SETTINGS
Flip up the dial handle and rotate the odor dial
to adjust odor neutralizer technology intensity
or to unlock the dial for cartridge access.
Flip up the handle and rotate the dial clockwise
until the two teal arrows are aligned. Pull the
handle to remove the dial from the nozzle.
Rotate the cartridge counterclockwise
in the dialhousing and pull out the
cartridge to remove it.
Align the yellow arrow on the side of the cartridge
with the yellow arrow on the side of the dial
cover, then insert the cartridge into the dial.
Rotate the cartridge clockwise to lock it in place.
Dispose of the old cartridge by
dropping it into the trash.
Remove the new odor cartridge from
the sealed packaging. To maintain the
life of the cartridge, keep it in the sealed
packaging until you are ready to install it.
Align the teal arrow on the dial cover with
the teal arrow on the nozzle, then reinsert
the dial into the nozzle. Rotate the dial
counterclockwise until it clicks into
an intensity setting to engage. Rotate
further to change the intensity setting.
ODOR DIAL
1. REMOVE ODOR DIAL
FROM NOZZLE
2. REMOVE OLD ODOR
CARTRIDGE
3.REMOVE NEW CARTRIDGE
FROM BAG
5. INSTALL DIAL IN NOZZLE
4. INSTALL NEW CARTRIDGE
IN DIAL
6. USED CARTRIDGE
DISPOSAL
NOTE: Odor cartridges need to be replaced for
optimal odor neutralizer technology experience. We
recommend changing cartridges when new bad odors
are experienced.
NOTES: • The odor dial needs to be installed for the vacuum to function properly, with or without the odor cartridge.
• Odor Neutralizer technology eectively deodorizes while interacting with odors from inanimate sources.
Insertion/Removal: Rotate the odor dial to align the teal arrows. Remove the dial to access the
odor cartridge for removal or replacement.
Low: Rotate the dial toward the Low position to decrease the intensity to the lowest level when
the vacuum is in use.
High: Rotate the dial toward the High position for the highest intensity level when the vacuum
is in use. This position is the recommended setting for optimal performance.
Odor Dial Must be Installed for Vacuum to Function Properly
• Remove odor cartridge from dial if you don’t want the benefits of the odor neutralization
technology.
Maintenance Required
• Clean all filters as recommended under Cleaning Filters.
• Empty the dust cup before storing your vacuum.
• Replace the cartridge as recommended under Odor Cartridge Replacement.
• Visit qr.sharkclean.com/odortech to learn more and purchase replacements.
• If wet pet messes are cleaned up, thoroughly clean the vacuum.
Fragrance Strength Over Time
• The intensity of the odor neutralizer technology’s fragrance may diminish over time. It may
also have no noticeable fragrance at all. This is natural and does not indicate the technology
isn’t working. Follow replacement instructions to ensure continued performance.
TURN UNTIL
CLICK TO LOCK
sharkclean.comsharkclean.com
ODOR NEUTRALIZER TECHNOLOGY
ODOR CARTRIDGE REPLACEMENT
TECHNOLOGY SETTINGS
ODOR NEUTRALIZER TECHNOLOGY TIPS
SETTINGS
Flip up the dial handle and rotate the odor dial
to adjust odor neutralizer technology intensity
or to unlock the dial for cartridge access.
Flip up the handle and rotate the dial clockwise
until the two teal arrows are aligned. Pull the
handle to remove the dial from the nozzle.
Rotate the cartridge counterclockwise
in the dialhousing and pull out the
cartridge to remove it.
Align the yellow arrow on the side of the cartridge
with the yellow arrow on the side of the dial
cover, then insert the cartridge into the dial.
Rotate the cartridge clockwise to lock it in place.
Dispose of the old cartridge by
dropping it into the trash.
Remove the new odor cartridge from
the sealed packaging. To maintain the
life of the cartridge, keep it in the sealed
packaging until you are ready to install it.
Align the teal arrow on the dial cover with
the teal arrow on the nozzle, then reinsert
the dial into the nozzle. Rotate the dial
counterclockwise until it clicks into
an intensity setting to engage. Rotate
further to change the intensity setting.
ODOR DIAL
1. REMOVE ODOR DIAL
FROM NOZZLE
2. REMOVE OLD ODOR
CARTRIDGE
3.REMOVE NEW CARTRIDGE
FROM BAG
5. INSTALL DIAL IN NOZZLE
4. INSTALL NEW CARTRIDGE
IN DIAL
6. USED CARTRIDGE
DISPOSAL
NOTE: Odor cartridges need to be replaced for
optimal odor neutralizer technology experience. We
recommend changing cartridges when new bad odors
are experienced.
NOTES: • The odor dial needs to be installed for the vacuum to function properly, with or without the odor cartridge.
• Odor Neutralizer technology eectively deodorizes while interacting with odors from inanimate sources.
Insertion/Removal: Rotate the odor dial to align the teal arrows. Remove the dial to access the
odor cartridge for removal or replacement.
Low: Rotate the dial toward the Low position to decrease the intensity to the lowest level when
the vacuum is in use.
High: Rotate the dial toward the High position for the highest intensity level when the vacuum
is in use. This position is the recommended setting for optimal performance.
Odor Dial Must be Installed for Vacuum to Function Properly
• Remove odor cartridge from dial if you don’t want the benefits of the odor neutralization
technology.
Maintenance Required
• Clean all filters as recommended under Cleaning Filters.
• Empty the dust cup before storing your vacuum.
• Replace the cartridge as recommended under Odor Cartridge Replacement.
• Visit qr.sharkclean.com/odortech to learn more and purchase replacements.
• If wet pet messes are cleaned up, thoroughly clean the vacuum.
Fragrance Strength Over Time
• The intensity of the odor neutralizer technology’s fragrance may diminish over time. It may
also have no noticeable fragrance at all. This is natural and does not indicate the technology
isn’t working. Follow replacement instructions to ensure continued performance.
TURN UNTIL
CLICK TO LOCK
sharkclean.comsharkclean.com
NOTE: All accessories are compatible with both the wand and the handle.NOTE: For deep carpet cleaning per ASTM F608 (embedded dirt in carpets), set to MAX suction and use setting II, Carpet.
WHOLE-HOME CLEANING
CLEANING MODES
To engage brushroll, step on floor
nozzle and tilt handle back.
Select surface setting:
O Power O
I Hard Floor
For bare floors and small area rugs,
the brushroll will spin slowly.
II Carpet
For carpets, the brushroll will spin
quickly to pick up stuck on debris.
The Suction Control slider located on the
handle allows you to adjust the suction
depending on the floor type.
MIN: to reduce suction and increase
maneuverability on carpets.
MAX: to increase suction on bare floors.
WHAT DOES THE BRUSHROLL INDICATOR LIGHT MEAN?
Solid Green Light: The brushroll is spinning and working as it should.
Solid Red Light: There is a jam in the brushroll area. Turn your vacuum o, unplug from
the wall and remove any blockages in the nozzle.
Flashing Red Light: The motorized floor nozzle is overheating. Turn o the vacuum,
unplug it and remove any blockages. Let the vacuum cool down for at least 60 minutes
before restarting. See Troubleshooting section for more information.
Flashing Green Light: The vacuum is operating in an environment that is either too hot
or too cold. This vacuum will only function properly in temperatures ranging from 32° F
(0°C) to 104°F (40°C). Turn the vacuum o and adjust the room temperature.
Press the Wand Release button to
detach the wand from the pod.
Press the Handle Release button to
detach the handle from the wand.
UPRIGHT
POWER/SURFACE SWITCH SUCTION CONTROL
INDICATOR LIGHT
ABOVE-FLOOR—WANDABOVE-FLOOR—HANDLE
Handle
WHOLE-HOME CLEANING
SETTINGS
BRUSHROLL INDICATOR LIGHT
Attach a cleaning accessory to
handle or wand.
ACCESSORIES—WANDACCESSORIES—HANDLE
sharkclean.comsharkclean.com
NOTE: All accessories are compatible with both the wand and the handle.NOTE: For deep carpet cleaning per ASTM F608 (embedded dirt in carpets), set to MAX suction and use setting II, Carpet.
WHOLE-HOME CLEANING
CLEANING MODES
To engage brushroll, step on floor
nozzle and tilt handle back.
Select surface setting:
O Power O
I Hard Floor
For bare floors and small area rugs,
the brushroll will spin slowly.
II Carpet
For carpets, the brushroll will spin
quickly to pick up stuck on debris.
The Suction Control slider located on the
handle allows you to adjust the suction
depending on the floor type.
MIN: to reduce suction and increase
maneuverability on carpets.
MAX: to increase suction on bare floors.
WHAT DOES THE BRUSHROLL INDICATOR LIGHT MEAN?
Solid Green Light: The brushroll is spinning and working as it should.
Solid Red Light: There is a jam in the brushroll area. Turn your vacuum o, unplug from
the wall and remove any blockages in the nozzle.
Flashing Red Light: The motorized floor nozzle is overheating. Turn o the vacuum,
unplug it and remove any blockages. Let the vacuum cool down for at least 60 minutes
before restarting. See Troubleshooting section for more information.
Flashing Green Light: The vacuum is operating in an environment that is either too hot
or too cold. This vacuum will only function properly in temperatures ranging from 32° F
(0°C) to 104°F (40°C). Turn the vacuum o and adjust the room temperature.
Press the Wand Release button to
detach the wand from the pod.
Press the Handle Release button to
detach the handle from the wand.
UPRIGHT
POWER/SURFACE SWITCH SUCTION CONTROL
INDICATOR LIGHT
ABOVE-FLOOR—WANDABOVE-FLOOR—HANDLE
Handle
WHOLE-HOME CLEANING
SETTINGS
BRUSHROLL INDICATOR LIGHT
Attach a cleaning accessory to
handle or wand.
ACCESSORIES—WANDACCESSORIES—HANDLE
sharkclean.comsharkclean.com
EMPTYING THE DUST CUP
To remove Dust Cup, slide up the latch on top of
dust cup handle. Tilt dust cup forward, then
lift to remove.
To reinstall, place bottom of dust cup into
pod and then tilt back until it clicks into place.
Press lower release button to open bottom
of dust cup.
To remove collected debris from Lint Screen,
press top release button and lift handle to
open. Gently brush lint screen to clean.
CLEAN HEPA FILTER
EVERY YEAR
Press down top of Filter Door. Tilt Filter
Door and lift out. Press tab at top of HEPA
Filter and pull away from the base of the
vacuum. To reinstall, insert HEPA filter into
unit and replace the filter door.
CLEAN PRE-MOTOR FILTERS
EVERY 3 MONTHS
Remove Dust Cup, then lift out Filters.
Regularly clean and replace the filters to keep your vacuum's suction power power and
to maximize the eectiveness of the odor neutralizer technology.
To prevent damage from cleaning chemicals rinse filters with cold water only. Allow all filters
to air-dry for at least 24 hours before reinstalling them to prevent liquid from being drawn
into electricparts.
CLEANING AND REPLACING THE FILTERS
CLEANING FILTERS
IMPORTANT: DO NOT use soap when cleaning the filters.
IMPORTANT: Unplug the power cord before performing any maintenance.
HEPA
Filter
Foam
Felt
Filter
Door
NOTE: To order replacement parts and filters, visit sharkaccessories.com.
Replacement
Pre-Motor Foam &
Felt Filter Kit
1239FT60
Replacement
HEPA Filter
1238FT60
Follow the previous instructions for removing filters. The Pre-Motor Filter should be replaced every
2.5 years. The HEPA Filter should be replaced every 3 years.
REPLACING FILTERS
sharkclean.comsharkclean.com
EMPTYING THE DUST CUP
To remove Dust Cup, slide up the latch on top of
dust cup handle. Tilt dust cup forward, then
lift to remove.
To reinstall, place bottom of dust cup into
pod and then tilt back until it clicks into place.
Press lower release button to open bottom
of dust cup.
To remove collected debris from Lint Screen,
press top release button and lift handle to
open. Gently brush lint screen to clean.
CLEAN HEPA FILTER
EVERY YEAR
Press down top of Filter Door. Tilt Filter
Door and lift out. Press tab at top of HEPA
Filter and pull away from the base of the
vacuum. To reinstall, insert HEPA filter into
unit and replace the filter door.
CLEAN PRE-MOTOR FILTERS
EVERY 3 MONTHS
Remove Dust Cup, then lift out Filters.
Regularly clean and replace the filters to keep your vacuum's suction power power and
to maximize the eectiveness of the odor neutralizer technology.
To prevent damage from cleaning chemicals rinse filters with cold water only. Allow all filters
to air-dry for at least 24 hours before reinstalling them to prevent liquid from being drawn
into electricparts.
CLEANING AND REPLACING THE FILTERS
CLEANING FILTERS
IMPORTANT: DO NOT use soap when cleaning the filters.
IMPORTANT: Unplug the power cord before performing any maintenance.
HEPA
Filter
Foam
Felt
Filter
Door
NOTE: To order replacement parts and filters, visit sharkaccessories.com.
Replacement
Pre-Motor Foam &
Felt Filter Kit
1239FT60
Replacement
HEPA Filter
1238FT60
Follow the previous instructions for removing filters. The Pre-Motor Filter should be replaced every
2.5 years. The HEPA Filter should be replaced every 3 years.
REPLACING FILTERS
sharkclean.comsharkclean.com
CHECKING FOR BLOCKAGES
Detach hose from vacuum pod,
and check hose and opening on
back of pod for blockages.
Detach wand from floor nozzle
and handle, and check both ends
for blockages.
Detach the wand from the pod,
place the pod on its side, and
check opening for blockages.
Detach the handle from the wand
and the hose from the vacuum pod,
and check openings for blockages.
Detach dust cup from vacuum pod.
Empty dust cup, remove debris from
lint screen, and check for blockages.
MAINTENANCE
NOTE: If any hair is wrapped around the brushroll, extending cleaning time will allow the self-cleaning brushroll to remove it for
you. If some fibers remain wrapped around brushroll after continued use, carefully remove them.
SELF-CLEANING BRUSHROLL
If any hair is wrapped around the brushroll, continue vacuuming, using Carpet mode on a bare
floor surface, a low-pile carpet, or a small area rug. This will allow the self-cleaning brushroll to
remove the hair wrap and send it to the dust cup.
If you run over a hard or sharp object or notice a noise change while vacuuming, check for
blockages or objects caught in the brushroll.
If some fibers remain wrapped around the brushroll after continued use, clear them from the brushroll.
Clean o any debris on the brushroll.
DEBRIS WRAPPED
AROUND BRUSHROLL
NOZZLE MAINTENANCE
To minimize the risk of power cord damage,
DO NOT run the vacuum over the power cord.
If this occurs, immediately shut o power to
the vacuum and remove the cord from the
brushroll or nozzle.
1. DO NOT pull or carry vacuum cleaner
by the cord or use cord as a handle.
2. DO NOT unplug by pulling on the cord.
Grasp the plug, not the cord.
3. DO NOT close the door on the cord.
4. DO NOT pull the cord around sharp
corners.
5. DO NOT leave the cord near heated
surfaces.
CORD MAINTENANCE
To access the nozzle hose, pinch the release
touchpoints on the bottom of the nozzle,
then lift the cover and clear any blockages.
NOZZLE HOSE BLOCKAGE
sharkclean.comsharkclean.com
CHECKING FOR BLOCKAGES
Detach hose from vacuum pod,
and check hose and opening on
back of pod for blockages.
Detach wand from floor nozzle
and handle, and check both ends
for blockages.
Detach the wand from the pod,
place the pod on its side, and
check opening for blockages.
Detach the handle from the wand
and the hose from the vacuum pod,
and check openings for blockages.
Detach dust cup from vacuum pod.
Empty dust cup, remove debris from
lint screen, and check for blockages.
MAINTENANCE
NOTE: If any hair is wrapped around the brushroll, extending cleaning time will allow the self-cleaning brushroll to remove it for
you. If some fibers remain wrapped around brushroll after continued use, carefully remove them.
SELF-CLEANING BRUSHROLL
If any hair is wrapped around the brushroll, continue vacuuming, using Carpet mode on a bare
floor surface, a low-pile carpet, or a small area rug. This will allow the self-cleaning brushroll to
remove the hair wrap and send it to the dust cup.
If you run over a hard or sharp object or notice a noise change while vacuuming, check for
blockages or objects caught in the brushroll.
If some fibers remain wrapped around the brushroll after continued use, clear them from the brushroll.
Clean o any debris on the brushroll.
DEBRIS WRAPPED
AROUND BRUSHROLL
NOZZLE MAINTENANCE
To minimize the risk of power cord damage,
DO NOT run the vacuum over the power cord.
If this occurs, immediately shut o power to
the vacuum and remove the cord from the
brushroll or nozzle.
1. DO NOT pull or carry vacuum cleaner
by the cord or use cord as a handle.
2. DO NOT unplug by pulling on the cord.
Grasp the plug, not the cord.
3. DO NOT close the door on the cord.
4. DO NOT pull the cord around sharp
corners.
5. DO NOT leave the cord near heated
surfaces.
CORD MAINTENANCE
To access the nozzle hose, pinch the release
touchpoints on the bottom of the nozzle,
then lift the cover and clear any blockages.
NOZZLE HOSE BLOCKAGE
sharkclean.comsharkclean.com
TROUBLESHOOTING
Vacuum is not picking up debris. No suction or light suction.
• Check filters to see if they need cleaning. Follow instructions for rinsing and air-drying the
filters before reinserting in the vacuum.
• Dust cup may be full; empty dust cup.
• Check hose, hose connections, nozzle, wand, pod, and accessories for blockages. Clear any
blockages found.
(Refer to Checking for Blockages section for more information.)
• If any string, carpet fibers, or hair is wrapped around the brushroll, extend cleaning time to
allow the self-cleaning brushroll to remove it.
– If some hair or fibers remain wrapped around brushroll after continued use, remove the
floor nozzle cover and carefully cut debris with scissors and remove from brushroll. See
Cleaning the Brushroll section for more information.
Vacuum lifts area rugs.
• Make sure Power/Surface switch is set to Hard Floor (setting I).
• Suction is powerful. Take care when vacuuming area rugs or rugs with delicately sewn edges.
Brushroll does not spin in carpet cleaning mode.
• If the Brushroll Indicator Light turns red, immediately turn o and unplug the vacuum.
Remove pod from floor nozzle and clear any blockages. Reconnect nozzle, plug in vacuum,
and turn on power.
• With the power on, recline the handle, which will automatically turn on the brushroll.
• Ensure that the Power/Surface switch is set to Carpet (setting II) for brushroll
to spin.
Vacuum turns o on its own or indicator light flashes red.
This vacuum is equipped with a motor-protective thermostat. If your vacuum overheats, the
thermostat will automatically turn the suction motor o. Perform the following steps to restart
thethermostat:
1. Turn vacuum o and unplug it.
2. Empty dust cup and clean filters (see Emptying the Dust Cup and Cleaning and
Replacing the Filters.).
3. Check for blockages in hose, accessories, and inlet openings.
4. Allow unit to cool for a minimum of 45 minutes.
5. Plug in vacuum and turn it on.
Vacuum is emitting air that smells bad.
• Dust cup may be full; empty dust cup. Empty dust cup after each use for optimal odor
neutralizer technology performance.
• Check filters to see if they need cleaning. Follow instructions for rinsing and air-drying the
filters before reinstalling them.
• Check to make sure odor cartridge is installed in the dial and the dial is installed in the
nozzle.
• Check the odor neutralizer technology dial on the nozzle to see what setting is enabled.
• If odor neutralizer technology dial is at any setting from Low to High and the cartridge has
been installed for 6 months or longer, consider replacing it.
• If the odor cartridge is still emitting a scent but you dislike it, consider turning the intensity
down, or reinstall the dial in the nozzle without the cartridge.
• If the odor neutralizer technology cartridge is not emitting a scent, consider replacing it.
For all other issues, please go to support.sharkclean.com/ or call Customer Service 1-800-798-7398.
AVAILABLE ACCESSORIES
B
I J
K
G H
F
E
D
A
Crevice Tool
Clean in corners and other tight spaces
or reach baseboards and ceilings with this
slim crevice tool.
B
Duster Crevice Tool
Two cleaning tools in one. The crevice tool
gives you extended reach to clean in tight
spaces, while the soft brush is ideal for dusting
delicate surfaces.
C
Upholstery Tool
Picks up hair, dust, and large debris from
mattresses, couches, curtains, lampshades,
and other delicate upholstered fabrics.
D
Pet Multi-Tool
A single convertible tool for cleaning tough pet
messes two ways: use the sti bristle brush to
clean stuck-on debris, or take o the bristles to
reveal an upholstery tool perfect for removing
stubborn pet hair and large piles of debris.
E
HairPro™ Self-Cleaning Pet Power Brush
Tackles pet hair and ground-in dirt from above-
floor areas like carpeted stairs and upholstery,
while actively removing hair wrap as it cleans.
F
Pet Power Brush
The turbine brush loosens and removes pet
hair and debris from carpets, and powerfully
deep-cleans dander out of upholstery and
other surfaces.
G
Pet Crevice Tool
This versatile, slender 8" tool removes pet
hair from hard-to-reach spaces like corners,
ceilings, and between couch cushions.
H
Under-Appliance Wand
Clean under and behind hard-to-move
appliances and furniture with this adjustable
36” tool. Flip the extension piece over to clean
the underside of appliances.
I
Anti-Allergen Dust Brush
This brush features nylon fiber bristles specifically
designed for removing fine dust and allergen
particles from the most delicate surfaces.
J
Home & Car Detail Kit
Deep-clean your car like a professional
detailer, or clean hard-to-reach areas in your
home. Micro-sized tools let you clean around
delicate objects and access the tightest spaces
like car vents and computer keyboards.
K
Accessory Bag
This convenient accessory storage bag
measures 32 cm x 70 cm and fits the Under-
Appliance Wand. Smaller size available at
sharkaccessories.com.
A
C
NOTE: Not all accessories come with all units. For a list of the accessories included with this model, see the top inside flap
of the box. To order additional accessories, visit sharkaccessories.com.
sharkclean.comsharkclean.com
TROUBLESHOOTING
Vacuum is not picking up debris. No suction or light suction.
• Check filters to see if they need cleaning. Follow instructions for rinsing and air-drying the
filters before reinserting in the vacuum.
• Dust cup may be full; empty dust cup.
• Check hose, hose connections, nozzle, wand, pod, and accessories for blockages. Clear any
blockages found.
(Refer to Checking for Blockages section for more information.)
• If any string, carpet fibers, or hair is wrapped around the brushroll, extend cleaning time to
allow the self-cleaning brushroll to remove it.
– If some hair or fibers remain wrapped around brushroll after continued use, remove the
floor nozzle cover and carefully cut debris with scissors and remove from brushroll. See
Cleaning the Brushroll section for more information.
Vacuum lifts area rugs.
• Make sure Power/Surface switch is set to Hard Floor (setting I).
• Suction is powerful. Take care when vacuuming area rugs or rugs with delicately sewn edges.
Brushroll does not spin in carpet cleaning mode.
• If the Brushroll Indicator Light turns red, immediately turn o and unplug the vacuum.
Remove pod from floor nozzle and clear any blockages. Reconnect nozzle, plug in vacuum,
and turn on power.
• With the power on, recline the handle, which will automatically turn on the brushroll.
• Ensure that the Power/Surface switch is set to Carpet (setting II) for brushroll
to spin.
Vacuum turns o on its own or indicator light flashes red.
This vacuum is equipped with a motor-protective thermostat. If your vacuum overheats, the
thermostat will automatically turn the suction motor o. Perform the following steps to restart
thethermostat:
1. Turn vacuum o and unplug it.
2. Empty dust cup and clean filters (see Emptying the Dust Cup and Cleaning and
Replacing the Filters.).
3. Check for blockages in hose, accessories, and inlet openings.
4. Allow unit to cool for a minimum of 45 minutes.
5. Plug in vacuum and turn it on.
Vacuum is emitting air that smells bad.
• Dust cup may be full; empty dust cup. Empty dust cup after each use for optimal odor
neutralizer technology performance.
• Check filters to see if they need cleaning. Follow instructions for rinsing and air-drying the
filters before reinstalling them.
• Check to make sure odor cartridge is installed in the dial and the dial is installed in the
nozzle.
• Check the odor neutralizer technology dial on the nozzle to see what setting is enabled.
• If odor neutralizer technology dial is at any setting from Low to High and the cartridge has
been installed for 6 months or longer, consider replacing it.
• If the odor cartridge is still emitting a scent but you dislike it, consider turning the intensity
down, or reinstall the dial in the nozzle without the cartridge.
• If the odor neutralizer technology cartridge is not emitting a scent, consider replacing it.
For all other issues, please go to support.sharkclean.com/ or call Customer Service 1-800-798-7398.
AVAILABLE ACCESSORIES
B
I J
K
G H
F
E
D
A
Crevice Tool
Clean in corners and other tight spaces
or reach baseboards and ceilings with this
slim crevice tool.
B
Duster Crevice Tool
Two cleaning tools in one. The crevice tool
gives you extended reach to clean in tight
spaces, while the soft brush is ideal for dusting
delicate surfaces.
C
Upholstery Tool
Picks up hair, dust, and large debris from
mattresses, couches, curtains, lampshades,
and other delicate upholstered fabrics.
D
Pet Multi-Tool
A single convertible tool for cleaning tough pet
messes two ways: use the sti bristle brush to
clean stuck-on debris, or take o the bristles to
reveal an upholstery tool perfect for removing
stubborn pet hair and large piles of debris.
E
HairPro™ Self-Cleaning Pet Power Brush
Tackles pet hair and ground-in dirt from above-
floor areas like carpeted stairs and upholstery,
while actively removing hair wrap as it cleans.
F
Pet Power Brush
The turbine brush loosens and removes pet
hair and debris from carpets, and powerfully
deep-cleans dander out of upholstery and
other surfaces.
G
Pet Crevice Tool
This versatile, slender 8" tool removes pet
hair from hard-to-reach spaces like corners,
ceilings, and between couch cushions.
H
Under-Appliance Wand
Clean under and behind hard-to-move
appliances and furniture with this adjustable
36” tool. Flip the extension piece over to clean
the underside of appliances.
I
Anti-Allergen Dust Brush
This brush features nylon fiber bristles specifically
designed for removing fine dust and allergen
particles from the most delicate surfaces.
J
Home & Car Detail Kit
Deep-clean your car like a professional
detailer, or clean hard-to-reach areas in your
home. Micro-sized tools let you clean around
delicate objects and access the tightest spaces
like car vents and computer keyboards.
K
Accessory Bag
This convenient accessory storage bag
measures 32 cm x 70 cm and fits the Under-
Appliance Wand. Smaller size available at
sharkaccessories.com.
A
C
NOTE: Not all accessories come with all units. For a list of the accessories included with this model, see the top inside flap
of the box. To order additional accessories, visit sharkaccessories.com.
sharkclean.comsharkclean.com
TIP: You can find the model and serial
numbers on the QR code label on the
bottom of the back of the vacuum pod.
Benefits of registering your product and
creating an account:
• Get easier, faster product support and
access to warranty information
• Access troubleshooting and product care
instructions
• Be among the first to know about
exclusive product promotions
RECORD THIS INFORMATION
Model Number:
����������������������������������������������������������������������������������������������������
Serial Number:
������������������������������������������������������������������������������������������������������
Date of Purchase:
��������������������������������������������������������������������������������������������
(Keep receipt)
Store of Purchase:
������������������������������������������������������������������������������������������
The Five (5) Year Limited Warranty applies to purchases made from authorized retailers of SharkNinja
Operating LLC. Warranty coverage applies to the original owner and to the original product only and is
not transferable.
SharkNinja warrants that the unit shall be free from defects in material and workmanship for a period
of five (5) years from the date of purchase when it is used under normal household conditions and
maintained according to the requirements outlined in the Owner’s Guide, subject to the following
conditions and exclusions:
What is covered by this warranty?
1. The original unit and/or non-wearable parts deemed defective, in SharkNinja’s sole discretion, will be
repaired or replaced up to five (5) years from the original purchase date.
2. In the event a replacement unit is issued, the warranty coverage ends six (6) months following the
receipt date of the replacement unit or the remainder of the existing warranty, whichever is later.
SharkNinja reserves the right to replace the unit with one of equal or greater value.
What is not covered by this warranty?
1. Normal wear and tear of wearable parts (such as foam filters, HEPA filters, pads, etc.), which require
regular maintenance and/or replacement to ensure the proper functioning of your unit, are not covered
by this warranty. Replacement parts are available for purchase at sharkaccessories.com.
2. Any unit that has been tampered with or used for commercial purposes.
3. Damage caused by misuse (e.g., vacuuming up water or other liquids), abuse, negligent handling, failure
to perform required maintenance (e.g., not cleaning the filters, not removing debris from the brushroll),
or damage due to mishandling in transit.
4. Consequential and incidental damages.
5. Defects caused by repair persons not authorized by SharkNinja. These defects include damages caused
in the process of shipping, altering, or repairing the SharkNinja product (or any of its parts) when the
repair is performed by a repair person not authorized by SharkNinja.
6. Products purchased, used, or operated outside North America.
How to get service
If your appliance fails to operate properly while in use under normal household conditions within the warranty
period, visit sharkclean.com/support for product care and maintenance self-help. Our Customer Service
Specialists are also available at 1-800-798-7398 to assist with product support and warranty service options,
including the possibility of upgrading to our VIP warranty service options for select product categories. So we
may better assist you, please register your product online at registeryourshark.com and have the product on
hand when you call.
SharkNinja will cover the cost for the customer to send in the unit to us for repair or replacement. A fee of
$25.95 (subject to change) will be charged when SharkNinja ships the repaired or replacement unit.
How to initiate a warranty claim
You must call 1-800-798-7398 to initiate a warranty claim. You will need the receipt as proof of purchase.
We also ask that you register your product online at registeryourshark.com and have the product on hand
when you call, so we may better assist you. A Customer Service Specialist will provide you with return and
packing instruction information.
How state law applies
This warranty gives you specific legal rights, and you also may have other rights that vary from state to state.
Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above
may not apply to you.
FIVE (5) YEAR LIMITED WARRANTY
TECHNICAL SPECIFICATIONS
Voltage: 120V~, 60Hz
Watts: 1,150W
ODOR NEUTRALIZER TECHNOLOGY SPECIFICATIONS
1. Product Name: Odor Neutralizer Technology Cartridge
2. Manufacturer: Shark Ninja 89 A Street Needham, MA 02494
3. Weight: 17.6g / 0.62oz
4. Ingredients: Solid SM composite polymer C17 + fragrance SE 272235
REGISTER YOUR PURCHASE
registeryourshark.com
Scan QR code using
mobile device
Scan here or visit
qr.sharkclean.com/odortech
for more information
sharkclean.comsharkclean.com
TIP: You can find the model and serial
numbers on the QR code label on the
bottom of the back of the vacuum pod.
Benefits of registering your product and
creating an account:
• Get easier, faster product support and
access to warranty information
• Access troubleshooting and product care
instructions
• Be among the first to know about
exclusive product promotions
RECORD THIS INFORMATION
Model Number:
����������������������������������������������������������������������������������������������������
Serial Number:
������������������������������������������������������������������������������������������������������
Date of Purchase:
��������������������������������������������������������������������������������������������
(Keep receipt)
Store of Purchase:
������������������������������������������������������������������������������������������
The Five (5) Year Limited Warranty applies to purchases made from authorized retailers of SharkNinja
Operating LLC. Warranty coverage applies to the original owner and to the original product only and is
not transferable.
SharkNinja warrants that the unit shall be free from defects in material and workmanship for a period
of five (5) years from the date of purchase when it is used under normal household conditions and
maintained according to the requirements outlined in the Owner’s Guide, subject to the following
conditions and exclusions:
What is covered by this warranty?
1. The original unit and/or non-wearable parts deemed defective, in SharkNinja’s sole discretion, will be
repaired or replaced up to five (5) years from the original purchase date.
2. In the event a replacement unit is issued, the warranty coverage ends six (6) months following the
receipt date of the replacement unit or the remainder of the existing warranty, whichever is later.
SharkNinja reserves the right to replace the unit with one of equal or greater value.
What is not covered by this warranty?
1. Normal wear and tear of wearable parts (such as foam filters, HEPA filters, pads, etc.), which require
regular maintenance and/or replacement to ensure the proper functioning of your unit, are not covered
by this warranty. Replacement parts are available for purchase at sharkaccessories.com.
2. Any unit that has been tampered with or used for commercial purposes.
3. Damage caused by misuse (e.g., vacuuming up water or other liquids), abuse, negligent handling, failure
to perform required maintenance (e.g., not cleaning the filters, not removing debris from the brushroll),
or damage due to mishandling in transit.
4. Consequential and incidental damages.
5. Defects caused by repair persons not authorized by SharkNinja. These defects include damages caused
in the process of shipping, altering, or repairing the SharkNinja product (or any of its parts) when the
repair is performed by a repair person not authorized by SharkNinja.
6. Products purchased, used, or operated outside North America.
How to get service
If your appliance fails to operate properly while in use under normal household conditions within the warranty
period, visit sharkclean.com/support for product care and maintenance self-help. Our Customer Service
Specialists are also available at 1-800-798-7398 to assist with product support and warranty service options,
including the possibility of upgrading to our VIP warranty service options for select product categories. So we
may better assist you, please register your product online at registeryourshark.com and have the product on
hand when you call.
SharkNinja will cover the cost for the customer to send in the unit to us for repair or replacement. A fee of
$25.95 (subject to change) will be charged when SharkNinja ships the repaired or replacement unit.
How to initiate a warranty claim
You must call 1-800-798-7398 to initiate a warranty claim. You will need the receipt as proof of purchase.
We also ask that you register your product online at registeryourshark.com and have the product on hand
when you call, so we may better assist you. A Customer Service Specialist will provide you with return and
packing instruction information.
How state law applies
This warranty gives you specific legal rights, and you also may have other rights that vary from state to state.
Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above
may not apply to you.
FIVE (5) YEAR LIMITED WARRANTY
TECHNICAL SPECIFICATIONS
Voltage: 120V~, 60Hz
Watts: 1,150W
ODOR NEUTRALIZER TECHNOLOGY SPECIFICATIONS
1. Product Name: Odor Neutralizer Technology Cartridge
2. Manufacturer: Shark Ninja 89 A Street Needham, MA 02494
3. Weight: 17.6g / 0.62oz
4. Ingredients: Solid SM composite polymer C17 + fragrance SE 272235
REGISTER YOUR PURCHASE
registeryourshark.com
Scan QR code using
mobile device
Scan here or visit
qr.sharkclean.com/odortech
for more information
© 2022 SharkNinja Operating LLC. POWERFINS, ROTATOR and SHARK are registered trademarks of SharkNinja
Operating LLC. HAIRPRO is a trademark of SharkNinja Operating LLC.
ZU100Series�IB�REV�Mv1
PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE.
This Owner’s Guide is designed to help you get a complete understanding of your new
Shark® Rotator® with PowerFins® HairPro™ and Odor Neutralizer Technology Upright Vacuum.
SharkNinja Operating LLC
US: Needham, MA 02494
CAN: Ville St-Laurent, QC H4S 1A7
1-800-798-7398
sharkclean.com
Illustrations may dier from actual product. We are constantly striving to improve our products;
therefore the specifications contained herein are subject to change without notice.
This product may be covered by one or more U.S. patents. See sharkninja.com/patents
for more information.
