Loading ...
Loading ...
Loading ...
English
Motor housing/Ice pack
Tamper/Container base holder
Cap/Cover/Cover gasket
How to Clean
Unplug before cleaning.
Clean the product before your first use and after each use.
Do not clean the blender before it cools down.
Remove any demountable parts before cleaning.
Some discoloration may occur upon usage but it does not affect usage.
Do not use benzine, thinner, alcohol, bleach, polishing powder, metal brushes or nylon brushes, otherwise the surface will be damaged.
Wipe with a well-wrung cloth.
Wash with diluted dish soap (neutral) and a soft sponge.
Then rinse thoroughly with water and dry well.
* Dishwasher safe
Note
After the ice pack is clean and dry, keep it in the
refrigerator for next use.
* Dishwasher safe
Assemble/Disassemble the tamper
by referring to the above figure.
Wash with diluted dish soap (neutral) and a soft sponge.
Then rinse thoroughly with water and dry well.
* NOT dishwasher safe
Blender container/Container gasket/Drip tray
Wash with diluted dish soap (neutral) and a soft sponge.
Then rinse thoroughly with water and dry well.
Before cleaning, be sure to take out the container gasket (it might
be lost during the cleaning process).
* Dishwasher safe
Blender container base
Wash with diluted dish soap (neutral) and a soft sponge.
Then rinse thoroughly with water and dry well.
* NOT dishwasher safe
Pay attention when handling the blender container
base. Blade is sharp.
Troubleshooting
Problem
The appliance does not
turn on.
The power plug is not in the outlet.
Insert the plug down to the root.
The power switch is not turned on.
Turn on the power switch that is located in the back.
The overload protection was triggered.
Press the reset button on the bottom of the motor housing (P. EN21).
No auto menu can be
selected.
The blender container is not set correctly.
Re-set blender container correctly. (P. EN14)
Manual mode or an auto menu selection is chosen during blending.
Select an auto menu selection or manual mode after motor is stopped.
Buttons are pressed while wearing gloves.
Press the buttons with a bare hand.
The button was pressed with a wet hand.
Dry your hand and press the button again.
Button not pressed.
Be sure to press on the illustration of the button.
is on, the appliance
does not start
blending.
The blender container is not set correctly.
Re-set blender correctly.
An auto menu selection or manual mode is not selected.
Select an auto menu selection or manual mode.
The ingredients are jammed.
Take out ingredients from the blender container and put them back in.
Chosen menu selection
is cancelled. (All menu’s
indicators are flashing.)
The stop/start key is not pressed within 10 seconds after menu selection is chosen.
Menu selection is cancelled after 10 seconds of inactivity for the
prevention of a motor operation malfunction. Select an auto menu
selection or manual mode again and press “ ” within 10 seconds.
Time on the auto
Maximum and minimum blending time is set for each menu and varies.
Adjust the time to be in the each menu selection's range. (P. EN12)
The appliance stops
during blending.
The overload protection is activated.
Too many ingredients
Blending hard ingredients
Abnormal noise or vibration
Release the overload protection. (P. EN21)
Using sticky ingredients
Add liquid.
Maximum operating time (approximately 9 minutes 40 seconds) is exceeded.
Turn off the power and resume after 10 minutes of rest.
The safety lock is activated due to tilt blender container when using the tamper.
Re-start and hold the lid while using the tamper.
Please check following points before arranging for service.
Parts that can be washed in a dishwater
putting it into the dishwasher.
High temperature may damage the parts, so
please keep the parts away from any heat
radiating devices, or lower their temperature.
CAUTION:
CAUTION:
Loading ...
Loading ...
Loading ...