Sencor SES 7220BK Automatic Espresso Maker User Manual

AUTOMATIC ESPRESSO MACHINE

Translation of the original manual

SES 7220BK

1 2

78 9

2 3 4 5 6

10 11 12

C1 C2 C3

D E

F1 F2

G1 G2

- 1 -

Revision 06/2022

EN Automatic Espresso Machine

Important safety instructions

READ CAREFULLY AND STORE FOR FUTURE USE

General warnings

• This appliance may not be used by children. Keep the

appliance and its power cord away from children.

• The appliance may be used by persons with reduced

physical, sensory or mental capabilities or with a lack of

experience and knowledge, if they are supervised or have

been instructed to use the appliance in a safe manner and

understand the potential dangers.

• Children must not play with the appliance.

• Cleaning and maintenance performed by the user must

not be performed by children unless they are older than

8years of age and under supervision.

• Keep the appliance and its power cord out of the reach of

children younger than 8 years.

• In the event that the power cord is damaged, have it

repaired at a professional service centre to prevent causing

a dangerous situation. It is forbidden to use the appliance if

it has a damaged power cord.

• This appliance is intended for home use. It is not intended

for use in locations such as:

– kitchens in stores; offices and other workplaces;

– in agriculture;

– guests of hotels, motels and other accommodation

- 2 -

Revision 06/2022

locations;

– in bed and breakfast establishments.

• Do not submerge the power plug, the power cord or the

appliance in water or in any other liquid.

WARNING:

The hopper must not be opened during use.

WARNING:

Do not spill anything on the power plug.

• Always clean the parts of the appliance that come into

contact with food using warm water with a small amount

of neutral dishwashing detergent, then rinse with clean

water and wipe dry.

WARNING:

Incorrect use may result in a risk of injury.

• The exterior surface of the appliance heats up during use

and may remain hot for a certain time afterwards. Be very

careful.

• The appliance must not be located inside a cabinet when it

is used.

• Before connecting the appliance to a power socket, check that the rated voltage on its rating label matches the electrical voltage in the power

socket.

• Connect the appliance only to a properly grounded socket. For safety reasons, we do not recommend using multi-socket adapters or extension

cords.

• Do not place the appliance on window sills, kitchen sink drainboards or unstable surfaces. Always place it on a stable, even and dry surface.

• Do not place the appliance on or near an electrical or gas stove, or in the vicinity of an open flame.

• Never use the appliance in the near vicinity of a bath, shower or swimming pool.

• Use the appliance only for the purposes for which it was designed.

• Use the appliance according to the instructions in the user’s manual. Otherwise, injuries, damage to the appliance or a dangerous situation may

result.

• Only use the appliance with the original accessories that came with it.

• To ensure sufficient air circulation, free space of at least 15 cm must be maintained around and above the appliance when it is running.

• Only use the top surface of the appliance for warming cups. Do not use it as a place for storing items.

- 3 -

Revision 06/2022

• Fill the water tank with clean cold water. Do not pour hot water or other liquids into it or place any items inside it.

• Before turning on the appliance, check that:

– the drip tray together with the grate is installed in position;

– the water tank is filled with a sufficient amount of water and is properly installed in position. The water level must not exceed the water level mark.

• When operating the appliance, be especially careful to avoid scalding by boiling water or steam.

• The hot water function must not be used continuously, no more than one full water tank at a time.

• Regularly inspect the water level in the water tank when using the appliance. When the water level falls below the minimum water level mark, add

water. Before adding water, first turn the appliance off and disconnect it from the power socket.

• Use the built-in coffee grinder only for grinding coffee beans. Do not use it for any other purposes.

• Ensure that no hair or other items enter the grinder while it is grinding. The coffee bean hopper lid should always be properly closed unless one is

refilling coffee beans or setting the fineness of the grind.

• To protect the pump from damage, the appliance is equipped with a built-in thermal fuse that will disengage it when it runs empty. In the event that

such a situation occurs, disconnect the power cord from the power socket and allow the appliance to cool down for at least 30 minutes. Then you

may continue using it.

• Do not move the appliance with a coffee cup located on the drip tray grate or with cups located on the cup warming surface.

• Ensure that the power cord does not come into contact with water or a hot surface.

• Disconnect the appliance from the power socket by pulling on the plug, never pulling on the power cord. Otherwise, this could damage the power

cord or the socket.

• The appliance is equipped with a removable power cord. If the power cord is damaged, it must replaced with a new original power cord.

• Do not submerge the appliance, the power cord or the power plug in water or in any other liquid.

• Prevent the power cord and power plug from coming into contact with water or another liquid.

• Make sure that the removable power cord does not come into contact with water or moisture.

• To avoid the danger of injury by electrical shock, do not repair the appliance yourself or make any adjustments to it. Have all repairs or adjustments

performed at an authorised service centre. By tampering with the appliance, you risk voiding your legal rights arising from unsatisfactory

performance or quality warranty.

- 4 -

Revision 06/2022

• Thank you for purchasing a SENCOR brand product and we hope that

you will be happy with it.

• Prior to using this appliance, please read the user‘smanual

thoroughly, even in cases, when one has already familiarised

themselves with previous use of similar types of appliances. Only use

the appliance in the manner described in this user’smanual. Keep

this user‘smanual in asafe place where it can be easily retrieved for

future use.

• We recommend saving the original cardboard box, packaging

material, purchase receipt and responsibility statement of the vendor

or warranty card for at least the duration of the legal liability for

unsatisfactory performance or quality. In the event of transportation,

we recommend that you pack the appliance in the original box from

the manufacturer.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

DESCRIPTION OF THE ESPRESSO MACHINE

A1 1.1-litre water tank

A2 Coffee bean hopper lid

A3 Coffee bean hopper, capacity

150g

Inside the hopper there is

agrinder with adjustable

grinding fineness.

A4 Touch control panel with

display

A5 Coffee and hot water brew

head, height adjustable.

A6 Coffee grounds container

A7 Inner drip tray

A8 Outer drip tray

A9 Removable power cord

A10 Steaming unit

A11 Service access door

A12 Cleaning aid

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

DESCRIPTION OF THE TOUCH CONTROL PANEL

B1 Insufficient water in the

water tank indicator light or

water tank not installed in its

location indicator light.

B2 Insufficient amount of coffee

beans in the coffee bean

hopper indicator light

B3 Full coffee grounds container

indicator light (indicator is lit)

or the inner drip tray / coffee

grounds container is not

correctly installed indicator

light (indicator is flashing)

B4 Steaming unit not inserted/

installed correctly indicator

light (indicator is lit) or service

access door is open or

incorrectly installed indicator

light (indicator is flashing)

B5 Descaling required indicator

light (indicator is lit) or

descaling process is running

indicator light (indicator is

flashing)

B6 Drain internal lines function is

running

B7 On/Off touch button

B8 Ground coffee amount

adjustment touch button

B9 Quick clean touch button

B10 Dispense hot water touch

button

B11 Brew espresso coffee touch

button

B12 Brew lungo coffee touch

button

Note:

The compartment contains three packets of descaling agent.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

BEFORE FIRST USE OF THE APPLIANCE

1. Remove all packaging materials from the appliance and remove any

protective film, promotional tags or labels.

2. Install the appliance on an even, dry and clean surface. Ensure that

there is free space around the appliance of at least 35cm above the top

part and 15cm around the sides.

3. Take out the water tank A1, rinse it out with clean water with the addition

of asmall amount of neutral dishwashing detergent. Then rinse it out

thoroughly using clean water, dry it and put it back in its place.

4. Properly attach the outer drip tray A8

to the appliance.

5. Wipe the outer surface of the appliance with alightly dampened cloth

and then wipe it thoroughly dry.

6. Fully unwind the removable power cord A9 and connect it to the

corresponding socket at the rear of the appliance.

7. To ensure optimal lifetime of the appliance, it is necessary to allow its

internal components to be rinsed out several times with hot water prior

to first use. For this purpose, use button B10, as described in chapter

»Rinsing out the espresso machine«.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

FILLING THE WATER TANK

1. Grasp the water tank A1 by its lid. It also serves as acarry handle. Lift

it up and remove it from the rear part of the appliance, see figure C1.

2. Fill the water tank A1 with clean water up to the maximum water

mark – see fig. C2, and insert it back into the appliance. Make sure

that the water tank A1 is properly installed in its place.

Note:

The water that you pour into the water tank A1 should ideally

be at room temperature (approximately 25°C). Water that is

too cold, could negatively affect the final taste of the coffee

beverage.

Warning:

The water tank A1 has amaximum capacity of

1.1litres of water. Do not overfill it. Never fill the water

tank A1 with warm or hot water, sparkling water or

other liquids such as, for example, milk. This could

damage the appliance. Never fill the water tank A1

by pouring in the water while it is inserted inside the

appliance (see fig. C3). There is adanger of splashing

the appliance or overfilling the water tank A1.

3. Do not leave water in the water tank A1 for longer than one day. For

brewing quality fresh coffee, it is necessary to always use fresh

water. Otherwise, the flavour of the resulting beverage may be

negatively affected.

Note:

When the indicator light B1 is lit, it is necessary to refill the

water tank A1 with water. Fill the water tank A1 with water

according to the above instructions.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

FILLING THE COFFEE BEAN HOPPER

1. Remove the coffee bean hopper lid A2.

2. Pour roasted coffee beans into the coffee bean hopper A3 and close

the lid A2. Do not leave the lid of the coffee bean hopper A2 open,

otherwise, the coffee beans will lose their aroma more quickly.

Warning:

The coffee bean hopper A3 has amaximum capacity

of 150g of coffee beans. Do not overfill it. Never fill the

coffee bean hopper A3 with ground or instant coffee,

caramelised or otherwise specially modified coffee

beans, cocoa beans or other items that could result in

damage to the appliance.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CONTROLLING THE FINENESS OF GROUND COFFEE

1. Use the grinding fineness regulator located inside the coffee bean

hopper A3 to set the grinding fineness of the coffee beans in

5levels, see figure D.

Automatic Espresso Machine

User’smanual

- 5 -

Revision 06/2022

2. Turning the regulator towards the position marked with the plus

symbol sets acoarser grind, and turning it in the opposite direction

sets afiner grind.

3. The fineness of the grind is set only while the grinder is running.

Otherwise, you could damage your appliance. For darker coffee

beans, we recommend setting acoarser grind, for lighter coloured

coffee beans, we recommend afiner grind.

4. If the brewed coffee is flowing out very slowly, it means that

the coffee grains are too finely ground and it is necessary to set

acoarser grind. On the other hand, if the brewed coffee is flowing out

too fast, it means that the coffee grains are too coarsely ground and

it is necessary to set afiner grind.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

RECOMMENDATIONS FOR PURCHASING AND STORING COFFEE

• To reduce the storage time, purchase coffee beans in smaller

packages.

• Use fresh roasted coffee beans with amarked roasting date and

consume them within 3 weeks of the roasting date.

• Store coffee beans in acool, dark and dry location, ideally in an

air-tight container.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

OPERATING THE ESPRESSO MACHINE

• Make sure that the power cord connector A9 is connected to the

appliance. Connect the power cord plug A9 to apower socket. Make

sure that the water tank A1 is refilled with fresh water and that the

coffee bean hopper A3 is filled with asufficient quantity of coffee

beans and that the appliance is properly assembled.

Note:

When refilling water and coffee beans, always follow the

instructions provided in chapter »Filling the water tank« and

»Filling the coffee bean hopper«.

• To start the appliance, press button

B7. The appliance will switch

to the stand-by mode.

• When you have finished using the espresso machine, press button

B7 to turn it off.

Note:

The automatic espresso machine is equipped with an

automatic shut-off function for when it is idle. Based on the

selected mode, the automatic espresso machine will shut off

after the preset time has elapsed. The automatic shut-off time

can be found in section«Setting the mode«.

Rinsing out the espresso machine

• To ensure the optimal lifetime of the appliance, it is necessary to allow

its internal components to be rinsed out several times with hot water

prior to first use.

1. Take out the outer drip tray A8 and place amug or bowl underneath

the brewing head A5, into which the espresso machine will dispense

water. Adjust the height of the brewing head A5 based on the size of

the cup.

2. Press button

B10. The button'sbacklight will be lit and the

espresso machine will start dispensing hot water.

3. The dispensing of hot water will stop automatically and the

button'sbacklight will turn off.

4. To thoroughly rinse out the internal components, we recommend

that the process is repeated 3 to 4 times.

5. When the rinsing process is finished, pour the water out of the mug

or bowl. Be especially careful since the water is very hot. Install the

outer drip tray A8 back in place. Refill the water in the water tank A1

as necessary.

Note:

Perform the rinsing process also when you have not used the

espresso machine for an extended period of time. The pump

will make anoise during the water dispensing process. This

is normal.

Brewing coffee

1. Place acup, mug or glass underneath the brewing head A5. Set the

height of the brewing head A5 by sliding it up or down depending on

the size of your cup, mug or glass – see figure E. If the cup or glass

is too tall, you may remove the outer drip tray A8. After removing the

cup or glass, return the drip tray A8 to its place.

2. Press button

B11 to brew espresso coffee or button B12 to

brew lungo coffee. Press button to confirm.

3. The espresso machine will automatically start the coffee grinding,

dosing and tamping process, and will dispense it.

4. As soon as the espresso machine has finished dispensing the coffee,

it will automatically switch to the stand-by mode.

Dispensing hot water

1. Pod hlavici A5 postavte šálek, hrnek nebo sklenici. Nastavte výšku

hlavice A5 posunutím směrem nahoru nebo dolů dle velikosti

vašeho šálku, hrnku nebo sklenice – viz obrázek E. Pokud je hrnek

nebo sklenice příliš vysoká, můžete vnější odkapávací tácek A8

odejmout. Po odejmutí hrnku nebo sklenice vraťte tácek A8 zpět na

své místo.

2. Stiskněte tlačítko

B10 atlačítko se podsvítí.

3. Kávovar automaticky spustí výdej horké vody.

4. Jakmile je proces výdeje vody dokončen, kávovar se automaticky

přepne do pohotovostního režimu.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

USER SETTINGS

Setting the amount of ground coffee

• Use the ground coffee amount adjustment when the brewed coffee is

too strong or too weak.

• Button

B8 serves to adjust the amount of ground coffee.

• Based on personal preferences, select the amount of ground coffee by

repeatedly pressing button

B8: small (approx. 7 g), medium

(approx. 8 g) or large

(approx. 10 g).

Setting the dispensed coffee / hot water volume

• The espresso machine enables the amount of dispensed coffee or

hot water to be adjusted based on your preferences in the range

25ml–250ml. The settings you make will be saved to the memory

of the espresso machine.

1. Place acup, mug or glass underneath the brewing head A5.

2. Turn on the espresso machine by pressing button

B7 .

3. Hold down button

B11 (to brew espresso coffee), B12 (to

brew lungo coffee) or

B10 (to dispense hot water). The espresso

machine will start dispensing coffee or water.

4. When the button is released, the dispensing of coffee or water will

stop. Abeep is made and the set amount of coffee or water will be

saved to the memory of the espresso machine.

Setting the mode

• The espresso machine can be set to an ECO mode, afast mode or

the default factory settings. In ECO mode, greater power savings are

achieved. In the fast mode, the coffee is prepared faster than with the

default factory settings.

ECO mode Fast mode

Default

settings

Indicator light Not lit Lit Lit

Pre-steam * Yes No Yes

Automatic shut-off

time

10 minutes 30 minutes 20 minutes

Option to set the

dispensed coffee

volume

Yes Yes Yes

*Note:

The pre-steam function means that the ground coffee is first steamed with

asmall amount of water. This will cause the coffee to swell and thereby

- 6 -

Revision 06/2022

when it is subsequently fully steamed, its flavour will be developed fully,

and its aromatic compounds and essential oils will be fully extracted.

1. In the stand-by mode, press and hold down button

B7 for

5seconds. Button

B7 will start flashing and at the same time

other buttons will also be flashing or lit depending on the mode that

is set.

Hot water

button

Espresso coffee

button

Lungo coffee

button

ECO mode

Lit Bliká Flashing

Fast mode

Flashing Lit Flashing

Default settings

Flashing Flashing Lit

2. To set the ECO mode, press button

B10, to set the fast mode,

press button B11 and to reset to default settings, press button

B12. After setting amode, 2beeps will be made. In the event

that you attempt to set amode that is already set, the appliance will

not react to the button being pressed.

3. If you do not wish to change the mode settings, press button

B7 once more, or wait 5seconds until the appliance automatically

switches back to the stand-by mode.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CLEANING AND MAINTENANCE

• Disconnect the power plug from the power socket and allow the

appliance to cool down before cleaning it.

Warning:

For cleaning, do not use cleaning products with an

abrasive effect, solvents, etc. that could damage the

appliance. No part of this appliance is intended for

washing in adishwasher.

Warning:

To prevent the risk of injury by electrical shock, do not

submerge the appliance, power cord or power plug in

water or any another liquid.

Quick clean

• The quick clean function is suitable for quickly removing dirty material

from the brew head A5 and the tubing lines.

1. Place acup, mug or glass underneath the brewing head A5.

2. Press button

B9 once. The espresso machine will automatically

start the quick clean function. Water will automatically start flowing

out of the brew head A5.

3. The quick clean process will automatically stop, however, it may

also be stopped by again pressing button

B9.

Note:

We recommend starting the quick clean function after every

use.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

EVERYDAY CLEANING AND MAINTENANCE

• Timely cleaning and maintenance is very important for operating the

appliance and extending its lifetime.

• Before cleaning, turn off the appliance, disconnect it from the power

socket and allow it to cool down.

Drip tray and the coffee grounds container

• Remove the outer drip tray A8 – see figure F1. Empty out all its

contents over asink, and wash it using clean water and then dry it

thoroughly.

• Be careful not to burn yourself when handling the drip tray A8. It may

contain hot water

• Slide out the inner drip tray A7 with the coffee grounds container A6

– see figure F2.

• Empty out the coffee grounds container A6 and wash it with clean

water. Then dry it thoroughly. Empty out the inner drip tray A7 and if

dirty, wipe it with aclean dampened cloth and then dry it thoroughly.

• Install the inner drip tray A7, coffee grounds container A6 and the

outer drip tray A8 back in their place.

Note:

If the icon B3

lights up while the espresso machine is

running, it means that the coffee grounds container A6 is full

and needs to be emptied out. If the icon B3

starts flashing,

it means that the coffee grounds container A6 is not inserted.

Steaming unit

• Slide out and remove the service access door A11 – see figure G1.

Press the steaming unit A10 release buttons and take it out – see

figure G2. Wash it under running water and dry it out thoroughly.

• Install the steaming unit A10 properly in its place and attach the

service access door A11.

Note:

If the icon B4

lights up, it means that the steaming unit

A10 is not inserted in its place or is not correctly installed. If

icon B4

is flashing, the service access door A11 is open or

incorrectly installed.

Water tank

• Take out the water tank A1, rinse it out with clean water with the

addition of asmall amount of neutral dishwashing detergent. Then

rinse it out thoroughly using clean water, dry it and put it back in its

place.

Coffee bean hopper

• Only clean the coffee bean hopper A3 with aclean, dry cloth or paper

towel. Do not clean it with water.

Outer surface of the espresso machine

• To clean the outer surface of the appliance, use aclean, lightly

dampened cloth. Then wipe everything so that it is thoroughly dry.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

DESCALING

• If indicator B5

lights up during operation, it is necessary to start

the descaling function.

• The appliance will work best when the descaling function is used

regularly, at least once per month, or more frequently based on the

hardness of the water that is used. This will extend its lifetime and

improve power efficiency because limescale deposits negatively affect

electricity consumption.

1. Fill the water tank A1 all the way to the maximum water mark

according to the instructions contained in chapter »Filling the water

tank«.

2. Add descaling agents specially intended for descaling espresso

machine type appliances into the water tank A1. This agent can be

purchased in standard retail chains. Follow the instructions on the

manufacturer'spackaging when dosing the purchased descaling

agent.

Warning:

For descaling, do not use vinegar, etc. Otherwise, the

appliance could be damaged.

3. Insert the power plug into apower socket.

4. Place asufficiently large container underneath the brew head A5.

5. In the stand-by mode, simultaneously press and hold down buttons

B7 and B11 for 5seconds. Abeep is made and the indicator

light B5

and button B11 will flash.

- 7 -

Revision 06/2022

6. To start the descaling process, press button B11.

Note:

In the event that you wish to return to the stand-by mode at

this stage, press button

B7.

7. The indicator light B5

will flash during the descaling process.

Take care to prevent scalding by hot water or the escaping steam.

Do not interrupt the process in this phase.

8. Once the water in the water tank A1 is used up, the indicator light B1

and button B11 will start flashing. Empty out the remaining

contents of the water tank A1 and fill it up to the maximum water

mark with clean water. When the filled water tank A1 is inserted back

into the appliance, indicator light B1

will turn off. The descaling

process will continue to run.

Note:

If necessary, empty out the container underneath the brew

head A5. Nevertheless, be careful when handling the

container since the water inside may be very hot.

9. When the self cleaning process is complete, the espresso machine

will turn off automatically.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

DRAINING THE INTERNAL LINES

• It is recommended to drain the internal lines when you plan on

not using the appliance for and extended period of time, before

transporting it, etc.

1. In the stand-by mode, simultaneously press and hold down buttons

B7 and B12 for 5seconds.

2. The indicator light B6

will start flashing.

3. Remove the water tank A1 from the appliance. Indicator B6

will

be lit. This signals that the draining of the internal lines is running.

Note:

If you press button

B7 before taking out the water tank A1,

you will return back to the stand-by mode.

4. When the internal line draining process is complete, the espresso

machine will turn off automatically.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CLEANING THE GROUND COFFEE OUTLET

• During use, ground coffee may accumulate on the walls of the

ground coffee outlet and therefore it is necessary to clean it regularly

(depending on the frequency of use).

1. Slide out and remove the service access door A11 – see figure G1.

Press the steaming unit A10 release buttons and take it out – see

figure G2.

2. Carefully tilt the espresso machine and using brush A12, carefully

remove any dirty material from the walls of the ground coffee

outlet– see figure H.

3. After cleaning it out, insert the steaming unit A10 and the service

access door A11 back in their place.

Storage

• When not using the appliance for an extended period of time,

disconnect the power plug from the power socket, allow the appliance

to cool down and clean it according to the instructions provided above.

• Before storing it, check that the appliance and all its accessories are

thoroughly clean and dry.

• Store the appliance in adry, clean and well-ventilated location not

exposed to extreme temperatures and out of children'sreach.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TROUBLESHOOTING

• The following table lists potential problems that may be encountered

during the use of the espresso machine. Nevertheless, if the problem

persists, turn off the espresso machine, disconnect the power plug

from the power socket and contact an authorised service centre.

Problem Cause Solution

The appliance is

not working.

It is not connected to

apower socket.

Connect it to aworking

power socket and press

button

B7.

Check that the power

cord is properly

connected to the socket

in the appliance and

that the plug is properly

inserted in the power

socket.

There is no

response when

abutton is

pressed or the

response is

delayed.

Electromagnetic

interference of the

appliance is occurring.

Turn off the appliance

and turn it back on again

after several minutes.

The touch panel is soiled.

Turn off the appliance,

disconnect it from the

power socket and clean

the panel using aclean,

lightly dampened cloth

and then thoroughly

wipe it dry.

Coffee is not

warm enough.

Cups have not been

warmed up.

Warm up the cups.

The steaming unit A10 is

too cold.

Flush it out three times

before brewing coffee.

Coffee is not

flowing out the

spout.

Prior to this you used

the drain internal lines

function.

Press the dispensing hot

water button until water

starts flowing from the

spout.

The first cup

does not taste

particularly good.

There is an insufficient

amount of ground coffee

inside the steaming

unit A10.

Pour out of the first

coffee that you brewed.

The next cup will now be

in order.

The coffee lacks

froth.

The coffee beans are

not fresh.

Use fresh coffee beans

or try using adifferent

brand of coffee.

Touch buttons

do not function

properly.

The touch buttons are

not pressed properly.

It is necessary to use the

appliance from the front.

Press the bottom part

of the icon of the touch

button.

The appliance

heats up for too

long.

The appliance is soiled

by limescale deposits.

Descale it according

to the instructions

contained in section

"Descaling".

The water tank

A1 is removed

or it is running

out of water, but

the respective

indicator light

is not signalling

anything.

The area around the

connector at the bottom

of the water tank A1 is

damp or wet.

Thoroughly dry out any

moisture or water in the

vicinity of the connector.

The inner drip tray

A7 is filled with

alarge amount of

water.

The coffee is ground

too fine, which prevents

water from flowing

through.

While the coffee grinder

is running, set acoarser

grind level.

The coffee

is dispensed

too slowly or

intermittently.

The coffee is ground

too fine, which prevents

water from flowing

through.

While the coffee grinder

is running, set acoarser

grind level.

The insufficient

coffee beans

indicator light

is flashing even

though there is

asufficient amount

of coffee beans in

the hopper.

The internal ground

coffee outlet is clogged.

Clean out the ground

coffee outlet of the

appliance according

to the instructions in

section "Cleaning the

ground coffee outlet".

- 8 -

Revision 06/2022

The descaling

process indicator

is flashing

continuously

even after the

descaling process

is finished.

The descaling process is

not yet finished.

Please be patient and

wait for the process to

finish. The appliance will

turn off automatically,

please do not turn off

this appliance manually.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TECHNICAL SPECIFICATIONS

Rated voltage range ............................................................................220 – 240 V~

Rated frequency ....................................................................................... 50 – 60 Hz

Rated power input .............................................................................1,235 – 1,470 W

Noise level .........................................................................................................75 dB(A)

The declared noise emission level of the appliance is 75dB(A), which

represents alevel Aof acoustic power with respect to areference acoustic

power of 1pW.

We reserve the right to change text and technical specifications.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF

USED PACKAGING MATERIALS

Dispose of used packaging material at asite designated for waste in your

municipality.

DISPOSAL OF USED ELECTRICAL AND ELECTRONIC EQUIPMENT

This symbol on products or original documents means that

used electric or electronic products must not be added to

ordinary municipal waste. For proper disposal, renewal and

recycling, hand over these products to determined

collection points. Alternatively, in some European Union

states or other European countries you may return your

appliances to the local retailer when buying an equivalent

new appliance.

Correct disposal of this product helps save valuable natural resources

and prevents potential negative effects on the environment and human

health, which could result from improper waste disposal. Ask your local

authorities or collection facility for more details.

In accordance with national regulations penalties may be imposed for the

incorrect disposal of this type of waste.

For business entities in European Union states

If you want to dispose of electric or electronic equipment, ask your retailer

or supplier for the necessary information.

Disposal in other countries outside the European Union.

This symbol is valid in the European Union. If you wish to dispose of this

product, request the necessary information about the correct disposal

method from the local council or from your retailer.

This product meets all the basic requirements of EU

directives related to it.

FAST ČR, a.s.

U Sanitasu 1621

CZ-251 01 Říčany

Sencor SES 7220BK Automatic Espresso Maker

Product's Documents

User Manual

Specifications

Sencor SES 7220BK Questions and Answers

Related Products

Sencor SES 7300BK Automatic Espresso Maker

Sencor SES 7018BK Automatic Espresso Maker

Sencor SES 7015CH Automatic Espresso Maker

Sencor SES 7210WH Automatic Espresso Maker

Sencor SES 7200BK Automatic Espresso Maker