Craftsman 917271100 16.5 HP ELECTRIC START 42" MOWER AUTOMATIC LAWN TRACTORR

Owner's Manual - Page 19

For 917271100. Also, The document are for others Craftsman models: 917.271100

PDF File Manual, 64 pages, Read Online | Download pdf file

917271100 photo
Loading ...
Loading ...
Loading ...
TRACTOR
Always observe safety rules when perform-
ing any maintenance.
BRAKE OPERATION
If tractor requires more than six (6) feet
stopping distance at high speed in highest
gear, then brake must be adjusted. (See
"TO ADJUST BRAKE" in the Service and
Adjustments section of this manual).
TIRES
Maintain proper air pressure in all tires
(See "PRODUCT SPECIFICATIONS" on
page 3 of this manual).
Keep tires free of gasoline, oil, or insect
control chemicals which can harm rub-
ber.
Avoid stumps, stones, deep ruts, sharp
objects and other hazards that may
cause tire damage.
NOTE: To seal tire punctures and prevent
flat tires due to slow leaks, tire sealant may
be purchased from your local parts dealer.
Tire sealant also prevents tire dry rot and
corrosion.
OPERATOR PRESENCE SYSTEM
Be sure that operator presence and inter-
lock systems are working properly. If your
tractor does not function as described
below, repair the problem immediately.
The engine should not start unless the
clutch/brake pedal is fully depressed and
attachment clutch control is in the disen-
gaged position.
When the engine is running, any attempt
by the operator to leave the seat without
first setting the parking brake should shut
off the engine.
When the engine is running and the
attachment clutch is engaged, any
attempt by the operator to leave the seat
should shut off the engine.
The attachment clutch should never
operate unless the operator is in the
seat.
BLADE CARE
For best results mower blades must be
kept sharp. Replace bent or damaged
blades.
BLADE REMOVAL
Raise mower to highest position to allow
access to blades,
Remove hex bolt, lock washer and flat
washer securing blade.
Install new or resharpened blade with
trailing edge up towards deck as shown.
19
IMPORTANT: To ensure proper assembly,
center hole in blade must align with star on
mandrel assembly.
Reassemble hex bolt, lock washer and
flat washer in exact Order as shown.
Tighten bolt securely (27-35 Ft. Lbs.
torque).
IMPORTANT: Blade bolt is Grade 8 heat
treated.
Trailing Blade Mandrel A,_sembly
Edge Up_(_j/ Center_
(Grade 8)_. .-_*'J_ "_'_,,_,
"_ Flat Washer"_-_
A Grade 8 heat treated boltcan be
identifiedby sixlineson the bolthead.
TO SHARPEN BLADE
NOTE: We do not recommend sharpening
blade, but if you do, be sure the blade is
balanced.
Care should be taken to keep the blade
balanced. An unbalanced blade will cause
excessive vibration and eventual damage
to mower and engine.
The blade can be sharpened with a file
or on a grinding wheel. Do not attempt to
sharpen while it is on the mower.
To check blade balance, you will need a
5/8" diameter steel bolt, pin, or a cone
balancer. (When using a cone balancer,
follow the instructions supplied with bal-
ancer).
NOTE: Do not use a nail for balancing
blade. The lobes of the center hole may
appear to be centered, but are not.
Slide blade onto an unthreaded portion
of the steel bolt or pin and hold the bolt
or pin parallel with the ground. If blade is
balanced, it should remain in a horizonta
position, if either end of the blade move.,
downward, sharpen the heavy end until
the blade is balanced.
Center Hole
or Pin
BATTERY
Your tractor has a battery charging system
which is sufficient for normal use.
However, periodic charging of the battery
with an automotive charger will extend its
life.
Loading ...
Loading ...
Loading ...