Loading ...
Loading ...
Loading ...
-
18
The motor cannot be switched off
(Programme selector switch to "0",
main switch to "0")
Petrol engine: Open the engine bonnet and close the fuel cock. Caution: Rotating V-belt!
Diesel engine: Open engine bonnet, actuate the emergency stop on the engine or close the fuel
cock. Caution: Rotating V-belt!
A short blow-off sound can be
heard.
The appliance is OK, the automatic filter cleaning system is working
Troubleshooting by the operator with plain text messages on the display
Note:
If the display messages shown remain despite the corrective measures described, contact service!
Display Meaning and consequence Corrective measures
1 Invalid KiK!
Operation locked
The identification of the inserted key is unknown.
– The appliance operation is prevented
Use approved Kärcher key!
2 Valid KiK but no
operation rights
The Kärcher key is known, however, not approved for
this appliance.
– The appliance operation is prevented
Use approved Kärcher key!
3 High dump tracer
stuck! Check it!
The function of the two-hand operation button is
checked for its safety function when the appliance is
switched on.
– When the two-hand operation button is pushed, the
operation is prevented during start-up
Release the two-hand operation button.
Confirm the message with the OK key (delete).
4 Locked HD-tracer
Hours: xxxxxhym+
The two-hand operation button (high emptying system)
was pushed in a sweeping programme.
– High emptying is prevented in the sweeping pro-
gramme for safety reasons.
Release the two-hand operation button.
Turn the programme selector switch to position
C (drive).
Press the two-hand operation button and keep it
down.
Operate the high emptying system by means of
the direction keys.
5 Sit on machine
for operation!
Appears when a sweeping or transport programme is
selected upon starting up the machine and no operator
is sitting on the seat.
– Start combustion engine and all appliance functions
are disabled
Sit on the driver's seat.
Note: The selected sweeping / transport opera-
tion starts fully automated.
Note: This procedure simultaneously serves the
inspection of the safety function of the seat
switch!
6 Low oil level engine!
Hours: xxxxxhym+
Is displayed during operation if the lubrication of the
combustion engine is no longer guaranteed.
– Combustion engine is shut off, all appliance functions
are disabled
Fill in motor oil
Perform a programme selector switch reset
(OFF position).
Combustion engine can be restarted.
7 Dirt pan open!
Hours: xxxxxhym+
Is displayed (low emptying system) as soon as a trans-
port or sweeping programme has been selected and at
least one waste container is removed.
– Start combustion engine and all appliance functions
are disabled
Lock all waste containers in place.
Turn the programme selector switch to "ON".
Note: The message disappears. The appliance
is ready for operation.
8 Dirt pan open?
Hours: xxxxxhym+
Is displayed (high emptying system) as soon as a
sweeping programme has been selected and the waste
container is not fully retracted and tipped inwards.
– All sweeping functions are disabled, the combustion
engine is running
Turn the programme selector switch to position
C (drive).
Press the two-hand operation button and keep it
down.
If necessary, tip the waste container inwards
and then lower it by means of the direction keys.
Note: In case of an attempt to completely lower a con-
tainer that is tipped outwards, a collision monitoring sys-
tem prevents the high emptying system from being dam-
aged
Release the two-hand operation button and the
direction keys.
Press the two-hand operation button and keep it
down.
Completely tip the container inwards by means
of the direction keys before lowering it.
Note: In case of an attempt to tip a retracted container
outwards, a collision monitoring system prevents the
high emptying system from being damaged
Release the two-hand operation button and the
direction keys.
Press the two-hand operation button and keep it
down.
Sufficiently raise the container by means of the
direction keys before it can be tipped outwards.
9 Brushpos. not ok
Hours: xxxxxhym+
Is displayed when the roller brush cannot move to the
factory-set end position.
– The appliance is ready for operation, however, the
sweeping result may be dissatisfying
Confirm the message with the OK key (delete).
Turn the programme selector switch to position
C (drive).
Change to the desired sweeping programme
again.
45EN
Loading ...
Loading ...
Loading ...