Loading ...
Loading ...
Loading ...
-
13
Check moving parts for freedom of
movement.
Check the sealing strips in the sweep-
ing area for position and wear.
Maintenance to be carried out every 100
operating hours:
Change engine oil (initial change after
20 operating hours).
Check and clean spark plug, replace if
necessary.
Clean air filter.
Maintenance to be carried out every 200
operating hours
Replace the air filter insert.
Clean the fuel filter.
Diesel engine: Clean oil filter, replace in
case of damage
Maintenance following wear:
Replace sealing strips.
Replace roller brush.
Replace side brush.
Note: In order to safeguard warranty
claims, all service and maintenance work
during the warranty period must be carried
out by the authorised Kärcher Customer
Service in accordance with the mainte-
nance booklet.
Maintenance to be carried out after 20 op-
erating hours:
Carry out initial inspection.
Maintenance to be carried out every 100
operating hours
Maintenance to be carried out every 200
operating hours
Maintenance to be carried out every 300
operating hours
� DANGER
Risk of injury!
When working on the high emptying
system, completely lift and secure the
waste container.
Perform the safeguarding only from
outside the hazard zone.
Insert safety support into the piston rod
for the lifting cylinder and secure it.
� DANGER
Risk of injury!
The engine requires approx. 3-4 sec-
onds to come to a standstill once it has
been switched off. During this time, stay
well clear of the working area.
Risk of burns!
Allow the machine sufficient time to cool
down before carrying out any mainte-
nance and repair work
.
ATTENTION
Engine oil, diesel and petrol must not be re-
leased into the environment. Protect the
ground and dispose of used oil in an envi-
ronmentally responsible way.
Park the sweeper on an even surface.
Turn the program selection switch to
"OFF".
Remove KIK-key.
Activate parking brake.
Allow device to cool down sufficiently.
Please observe the following warning notes
when handling batteries:
� DANGER
Risk of fire and explosion!
Risk of explosion! Do not put tools or
similar on the battery, i.e. on the termi-
nal poles and cell connectors.
Smoking and open flames must be
strictly avoided.
Rooms where batteries are charged
must have good ventilation because
highly explosive gas is emitted during
charging.
�
WARNING
Risk of injury!
Ensure that wounds never come into
contact with lead. Always clean your
hands after working on batteries.
Danger of causticization!
Rinse thoroughly with lots of clear water
if acid gets into the eye or comes in con-
tact with the skin.
Then consult a doctor immediately.
Wash off the acid If it comes in contact
with the clothes.
Change clothing.
Park the sweeper on an even surface.
Connect air pressure testing device to
tyre valve.
Check air pressure and adjust if re-
quired.
For permissible tyre inflation pressure
see Chapter "Technical specifications".
� WARNING
Risk of injury!
Check stability of ground. Park the vehi-
cle on stable grounds only, additionally
secure it against rolling away by means
of a wheel chock.
ATTENTION
Use a suitable commercially available vehi-
cle jack.
Park the machine on an even surface.
Check stability of ground. Lock the ap-
pliance to ensure that it does not roll off.
Place the jack at the relevant position
point.
Loosen the wheel nuts/wheel bolts by
about 1 revolution using a suitable tool.
Raise machine using vehicle jack.
Unscrew the wheel nuts/wheel bolts
and remove them.
Remove wheel.
Have a defective wheel repaired or re-
placed in a specialist workshop.
Place the wheel and screw in the wheel
nuts/wheel bolts all the way; tighten
them lightly.
Lower machine using vehicle jack.
Torque the wheel nuts/wheel bolts to
the required torque.
Contact the customer service for the re-
moval of the front wheel.
Do not sit down on the driver seat.
Turn the programme selector switch to
position C (drive).
If the message >Please sit down on
the machine< appears on the display,
the safety function is given.
� DANGER
Risk of burns on account of hot surfaces!
Park the machine on an even surface.
Allow engine to cool down.
Wait for at least 5 minutes after switch-
ing off the engine before checking the
engine oil fill level.
Open the engine hood.
Figure: Petrol motor (KM 105/...)
Maintenance by Customer Service
Maintenance Works
General notes on safety
Preparation
Safety notes regarding the batteries
Check the tyre pressure
Remove rear wheel
Torque (Nm) 56 Nm
Removing the front wheel
Check the function of the seat contact
switch
Check engine oil level and top up, if
required
40 EN
Loading ...
Loading ...
Loading ...