Loading ...
Loading ...
Loading ...
OPERATION
The operation of any tractor can result in foreign objects thrown into the eyes, which
can result in severe eye damage. Always wear safety glasses or eye shields while op-
erating your tractor or performing any adjustments or repairs. We recommend a wide
vision safety mask over spectacles or standard safety glasses.
HOW TO USE YOUR TRACTOR
TO SET PARKING BRAKE (See Fig. 6)
Your tractor is equipped with an operator presence sens-
ing switch. When engine is running, any attempt by the
operator to leave the seat without first setting the parking
brake will shut off the engine.
• Depress clutch/brake pedal into full "BRAKE" position
and hold,
• Place parking brake lever in "ENGAGED" position and
release pressure from clutch/brake pedal, Pedal should
remain in "BRAKE" position, Make sure parking brake
will hold tractor secure,
POSITION
IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY
POSITIONOTHERTHAN"STOP"WILL CAUSETHE BATTERY
TO BE DISCHARGED,(DEAD).
NOTE: Under certain conditions when tractor is standing
idle with the engine running, hot engine exhaust gases may
cause "browning" of grass, To eliminate this possibility, al-
ways stop engine when stopping tractor on grass areas,
CAUTION: Always stop tractor com-
pletely, as described above, before leav-
ing the operator's position; to empty
grass catcher, etc.
ATTACHMENT CLUTCH SWITCH
PULL OUT
ADJUSTMENT
KNOB
KEY
MOTION CONTROL
LEVER
PARKING BRAKE
ENGAGED"
POSITION
PARKING BRAKE
"DISENGAGED" POSITION
FIG. 6
STOPPING (See Fig. 6)
MOWER BLADES -
• To stop mower blades,move attachment clutch switch
to "DISENGAGED" position.
GROUND DRIVE -
• To stop ground drive, depress clutch/brake pedal into
full "BRAKE" position,,
• Move motion control lever to neutral (N) position,
IMPORTANT: THEMOTIONCONTROLLEVERDOESNOT
RETURNTO NEUTRAL(N) POSITIONWHEN THE CLUTCH/
BRAKEPEDALIS DEPRESSED.
ENGINE -
• Move throttle control between half and full speed (fast)
position,
NOTE: Failure to move throttle control between half and
full speed (fast) position, before stopping may cause engine
to "backfire".
• Turn ignition key to "STOP" position and remove key.
Always remove key when leaving tractor to prevent
unauthorized use,
• Never use choke to stop engine,
11
TO USE THROTTLE CONTROL (See Fig. 6)
Always operate engine at full throttle,
• Operating engine at less than full throttle reduces the
battery charging rate,
• Full throttle offers the best bagging and mower perfor-
mance,
TO MOVE FORWARD AND BACKWARD
(See Fig. 6)
The direction and speed of movement is controlled by the
motion control lever.
• Start tractor with motion control lever in neutral (N)
position,
• Release parking brake,
• Slowly move motion control lever to desired position.
TO ADJUST MOWER CUTTING HEIGHT (See
Fig. 6)
The cutting height is controlled by turning the height ad-
justment knob in desired direction.
• Turn knob clockwise (F_ ) to raise cutting height,
• Turn knob counterclockwise (F_) to lower cutting
height,
The cutting height range isapproximately 1-1/2" to 4", The
heights are measured from the ground to the blade tip with
the engine not running, These heights are approximate
and may vary depending upon soil conditions, height of
grass and types of grass being mowed,
• The average lawn should be cut to approximately 2-1/2
inches during the cool season and to over 3 inches
during hot months, For healthier and better looking
lawns, mow often and after moderate growth,
• For best cutting performance, grass over 6 inches
in height should be mowed twice. Make the first cut
relatively high; the second to desired height,
TO ADJUST GAUGE WHEELS (See Fig. 7)
Gauge wheels are properly adjusted when they are slightly
off the ground when mower is at the desired cutting height
in operating position, Gauge wheels then keep the deck
in proper position to help prevent scalping in most terrain
conditions.
Loading ...
Loading ...
Loading ...