Loading ...
Loading ...
Loading ...
PROBLEM
Dishes not
washing clean
CAUSED BY
Water is not
hot enough
SOLUTION
Water temperature should be at least 140°F [60°C]. Set
water heater thermostat to a higher setting Run water at
sink until hot before starting.
Cloudy film on
glassware,
etchlng -
permanent
correslon
Dishes &
Interior of
dishwasher
yellow or
brown
Rust spots on
stalnless steel
-OR-
Dark spots on
flatware -
stainless steel,
sllver plate, or
sterllng
Bronze tarnish
on silverplate
improper loading
Spray arm or arms not
rotating freely
Not enough detergent
or improper
detergent
"Old" detergent
Water pressure may
be low, dishwasher is
not filling properly
Too much detergent
in soft water
Inadequate rinsing
iron or manganese in
water
Allowing salty or
acidic foods such as
mayonnaise, vinegar
fruit juices, salad
dressings, milk
products to remain on
flatware
Undissolved
delergent coming in
contact with flatware
SilverpJate is worn off
Exposed base metal
lakes on a bronzed
hue
Make sure dishes and glassware are loaded so spray
reaches all surfaces and items .drain properly, Do not ov-
erload, Do not nest items
Make sure large items do not block spray from reaching
detergent dispensers
Check spray arms to make sure they turn freely after load-
ing Be sure a utensil has not prevented their turning
Use more dishwasher detergent. Use detergent with high-
est available phosphorus content..especially with hard
water
Use only fresh dishwasher detergent. Store tightly closed
container, in cool, dry place. Discard old detergent. Do not
fill dispensers until ready to starl dishwasher.
If water pressure is low, do not use waler for other purposes
while dishwasher is running [to assure correct fills)
Check for rainbow hue on glasses, A rainbow hue is the
first sign of etching (corrosion of glass] Reduce the amount
of dishwasher detergent Use a detergent with a lower
phosphorus content.
If water pressure is low do not use water for other purposes
while dishwasher is running (to assure correct water fills].
Make sure dishes and glassware are loaded properly to
assure adequate rinsing and draining Do not overload
Temporary remedy:
1 Set empty dishwasher for a "one wash" cycle
2 Start dishwasher and unlatch door to stop it when Jlhas
filled for the wash part of the cycle.
3. Add '& to '2 cup [120 to 240 mL] of citric acid crystals
(usually available in drugstores]
4. Close and talch door to complete cycle.
Permanent solution: Install an iron or manganese filter to
home wafer supply.
Rinse flatware that is to stand for several hours before
washing [use Rinse & Hold). Clean stained items with silver
polish and re-wash, Do not put stainless steel and sliver
flatware In the same sllverware basket compartment.
Direct contact between these metals can cause perma-
nerrt damage to the sllver.
Remove spots with silver polish. Avoid spilling concentrated
detergent on wet flatwa re.
Remove tarnish with silver polish Have silverreplated
Water left in
bottom of
dishwasher
Dishwasher cycle not
completed
Clogged drain air
gap
Allow dishwasher to complete cycle
Some plumbing codes require use of a drain air gap be-
tween an undercounter dishwasher and the drain system
of the house, The air gap is usually located above the sink
or on the top of the counter near the dishwasher to prevent
the possibility of water backing up from the drain into the
dishwasher due to a plugged drain, The drain air gap is
NOT a part of the dishwasher and is NOT covered by the
dishwasher warranty The drain air gap should be kepl
clean to insure proper draining of the dishwasher
13
Loading ...
Loading ...
Loading ...