PetSafe PIG00-11007 Premium In-Ground Cat Fence

User Manual - Page 19

For PIG00-11007.

PDF File Manual, 24 pages, Read Online | Download pdf file

PIG00-11007 photo
Loading ...
Loading ...
Loading ...
www.petsafe.net 19
Additional Information
The Boundary Wire is buried so that it is not accidentally tripped over or cut. Use care when trimming grass or digging
near the Boundary Wire to prevent damage.
The system should only be used with healthy pets. Contact your veterinarian if you have concerns about the medical
condition of your pet (medication, pregnant, heart conditions, etc.).
This system is not for vicious or aggressive pets. If your pet may pose a threat to others, DO NOT USE THIS SYSTEM.
If you are unsure if your pet is aggressive, please consult your veterinarian or a certifi ed trainer.
• The PetSafe
®
Deluxe In-Ground Cat Fence
is for residential use only.
The Static Correction will get your pet’s attention, but will not cause harm. It is designed to startle, not to punish.
Test the Receiver Collar every 2 months. Battery life depends upon how often the Receiver Collar is activated.
______________________________________________________
Short Loop Test
The Short Loop Test is a simple test to determine if each component (Fence Transmitter, Receiver Collar and Boundary
Wire) is functioning properly.
1. Disconnect the Boundary Wire and Ground Wire.
2. Cut approximately 10 feet of unused Boundary Wire and connect it to the Boundary Wire Terminals.
3. Attach the Test Light to the Receiver Collar.
4. Spread the Boundary Wire out into a circle. Set the Boundary Control Switch to B.
5. Set the Boundary Width Control knob to 10 and the Static Correction Level to 2 or above.
6. If the Loop Indicator Light is not lit, then your Fence Transmitter is not functioning properly. Contact the Customer
Care Center at 1-800-732-2677.
7. If the Loop Indicator Light is lit, disconnect one end of the Boundary Wire from the Boundary Wire Terminal.
8. If the loop alarm does not sound, the Fence Transmitter needs to be replaced. Contact the Customer Care Center at
1-800-732-2677.
9. If the loop alarm does sound, plug the Boundary Wire back into the Boundary Wire Terminal.
10. Hold the Receiver Collar next to the 10 foot length of Boundary Wire. The Receiver Collar should beep about
1 foot away from the Boundary Wire. The Test Light should then fl ash as you hold the Receiver Collar closer to the
Boundary Wire.
11. If Receiver Collar does not beep and the Test Light does not fl ash, replace the battery in the Receiver Collar. If it still
does not beep and the Test Light does not fl ash, contact the Customer Care Center at 1-800-732-2677.
12. If the Receiver Collar beeps, there may be a complete or partial break in the Boundary Wire. See the “To Locate a Break
in the Boundary Wire” section.
______________________________________________________
To Locate a Break in the Boundary Wire
Please follow these steps in determining where you have a break in your Boundary Wire:
1. Locate your original splice(s) and verify they have a good, solid connection.
2. Check your yard to determine any possible damage to the Boundary Wire (e.g. recent digging, aerating, rodent
burrowing, or any other noticeable disturbance in your yard next to the Boundary Wire).
If you still cannot fi nd the break in the Boundary Wire, follow the procedure below:
1. Unplug the Fence Transmitter.
2. Connect both ends of your twisted Boundary Wire to one Boundary Wire
Terminal.
3. Measure and cut a Test Wire which is half the length of your total Boundary
Wire footage.
4. Connect one end of Test Wire to the other Boundary Wire Terminal.
5. Locate the halfway point of your boundary and cut the Boundary Wire.
6. Splice the other end of the Test Wire to either side of your Boundary Wire where
you cut it in half.
7. Plug in the Fence Transmitter and check the Loop Indicator Light. If the Loop
Indicator Light is on, you can assume the break is in the other half of the
Boundary Wire.
Te s t
Wire
Loading ...
Loading ...
Loading ...