User Guide
For future use, STORE USER GUIDE
in location on bottom of base.
Car Seat
©2020 Artsana USA, Inc. 03/20
www.chiccousa.com
IS0151E_02
TABLE OF CONTENTS
Registration 2
Child Guidelines 4
Safe Use Checklist 6
Important Warnings 8
Best Practices 14
Need Help? 15
Vehicle Seating Positions 16
Vehicle Seat Belts 18
What is LATCH? 20
Child Restraint Components 22
Child Requirements 26
Install with Base Setup 28
Install Using LATCH 30
Install Using LAP-SHOULDER BELT 36
Install Using LAP BELT ONLY 42
Install Carrier to Base 46
Install without Base Setup 50
Install Using LAP-SHOULDER BELT 52
Install Using LAP BELT ONLY 56
Adjusting Harness Height 60
Securing Child with Harness 64
Secure Child Checklist
72
Base Release Handle 74
LATCH Storage 75
Newborn Positioner 76
Head Rest Insert 78
Handle Positions 79
Canopy 80
Installation on an Aircraft 81
Cleaning and Maintenance 82
VEHICLE INFORMATION
BASE INSTALLATION
SECURING YOUR CHILD
ADDITIONAL INFORMATION
For future reference, fill in the information below. The information can be found on the label
on the bottom of the Child Restraint.
Model Number:
Serial Number:
Manufactured In:
If you have any problems with your Chicco Child Restraint,
or any questions regarding installation or use, please call:
Chicco Customer Service
1-877-424-4226
Please have Model and Serial Number available when you call.
These are located on a label on the bottom of the Child Restraint.
WITHOUT BASE INSTALLATION
CHILD RESTRAINT OVERVIEW
TABLE OF CONTENTS
Registration 2
Child Guidelines 4
Safe Use Checklist 6
Important Warnings 8
Best Practices 14
Need Help? 15
Vehicle Seating Positions 16
Vehicle Seat Belts 18
What is LATCH? 20
Child Restraint Components 22
Child Requirements 26
Install with Base Setup 28
Install Using LATCH 30
Install Using LAP-SHOULDER BELT 36
Install Using LAP BELT ONLY 42
Install Carrier to Base 46
Install without Base Setup 50
Install Using LAP-SHOULDER BELT 52
Install Using LAP BELT ONLY 56
Adjusting Harness Height 60
Securing Child with Harness 64
Secure Child Checklist
72
Base Release Handle 74
LATCH Storage 75
Newborn Positioner 76
Head Rest Insert 78
Handle Positions 79
Canopy 80
Installation on an Aircraft 81
Cleaning and Maintenance 82
VEHICLE INFORMATION
BASE INSTALLATION
SECURING YOUR CHILD
ADDITIONAL INFORMATION
For future reference, fill in the information below. The information can be found on the label
on the bottom of the Child Restraint.
Model Number:
Serial Number:
Manufactured In:
If you have any problems with your Chicco Child Restraint,
or any questions regarding installation or use, please call:
Chicco Customer Service
1-877-424-4226
Please have Model and Serial Number available when you call.
These are located on a label on the bottom of the Child Restraint.
WITHOUT BASE INSTALLATION
CHILD RESTRAINT OVERVIEW
2
3
REGISTRATION REGISTRATION
Please complete the Registration Card that came with
your Child Restraint and mail it promptly.
Child Restraints could be recalled for safety reasons. You must register this restraint to be reached in
a recall. Send your name, address, e-mail address if available, and the restraint’s model number and
manufacturing date to:
Artsana USA, Inc.
1826 William Penn Way
Lancaster, PA 17601
or call 1-877-424-4226
or register online at http://www.chiccousa.com/carseatregistration.aspx
For recall information, call the U.S. Government’s Vehicle Safety Hotline at
1-888-327-4236 (TTY: 1-800-424-9153), or go to http://www.NHTSA.gov.
PAGE INTENTIONALLY LEFT BLANK
2
3
REGISTRATION REGISTRATION
Please complete the Registration Card that came with
your Child Restraint and mail it promptly.
Child Restraints could be recalled for safety reasons. You must register this restraint to be reached in
a recall. Send your name, address, e-mail address if available, and the restraint’s model number and
manufacturing date to:
Artsana USA, Inc.
1826 William Penn Way
Lancaster, PA 17601
or call 1-877-424-4226
or register online at http://www.chiccousa.com/carseatregistration.aspx
For recall information, call the U.S. Government’s Vehicle Safety Hotline at
1-888-327-4236 (TTY: 1-800-424-9153), or go to http://www.NHTSA.gov.
PAGE INTENTIONALLY LEFT BLANK
4
5
CHILD GUIDELINES
NEWBORN POSITIONER
4 lbs. 11 lbs. 22 lbs.
(1.8 kg) (5 kg) (10 kg)
CHILD GUIDELINES
ONLY use this Child Restraint if the child meets BOTH of the following
Weight and Height requirements:
• Weight is between 4 and 22 pounds (1.8 and 10 kg).
• Height is 30 inches (76 cm) or less and child's head is no less than
1" (25 mm) below the top of the head rest.
The Newborn Positioner is only for infants who weigh between 4 and 11
pounds (1.8 and 5 kg). See Newborn Positioner on page 76.
For premature infants, you must consult the infant's doctor before
using this Child Restraint. A premature infant may have difficulty breathing
or have other medical problems when placed in a seated position.
WARNING! Use of this Child Restraint is ONLY for children who meet ALL
of the requirements shown here. If the child is not within these requirements,
select a different car seat (such as a convertible car seat).
NEVER turn this Child Restraint FORWARD-FACING.
Discontinue the use of this Child Restraint as soon as the child
reaches either the maximum weight OR maximum height.
4
5
CHILD GUIDELINES
NEWBORN POSITIONER
4 lbs. 11 lbs. 22 lbs.
(1.8 kg) (5 kg) (10 kg)
CHILD GUIDELINES
ONLY use this Child Restraint if the child meets BOTH of the following
Weight and Height requirements:
• Weight is between 4 and 22 pounds (1.8 and 10 kg).
• Height is 30 inches (76 cm) or less and child's head is no less than
1" (25 mm) below the top of the head rest.
The Newborn Positioner is only for infants who weigh between 4 and 11
pounds (1.8 and 5 kg). See Newborn Positioner on page 76.
For premature infants, you must consult the infant's doctor before
using this Child Restraint. A premature infant may have difficulty breathing
or have other medical problems when placed in a seated position.
WARNING! Use of this Child Restraint is ONLY for children who meet ALL
of the requirements shown here. If the child is not within these requirements,
select a different car seat (such as a convertible car seat).
NEVER turn this Child Restraint FORWARD-FACING.
Discontinue the use of this Child Restraint as soon as the child
reaches either the maximum weight OR maximum height.
6
7
Make sure your child meets the age, weight, and height requirements:
Refer to the “Child Guidelines” section on page 4.
If using Base, make sure Carrier is securely attached to Base:
Refer to the “Install Carrier to Base” section on page 46.
Select a safe seating location in your car:
Refer to the “Vehicle Seating Positions” section on page 16 and 17.
Install Base or Carrier Rear-Facing ONLY:
Refer to the “Child Guidelines” section on page 4.
SAFE USE CHECKLIST
YOUR CHILD’S SAFETY DEPENDS ON YOU! You MUST follow the
detailed instructions in this User Guide to ensure the steps below are
performed correctly!
Ensure that the Child Restraint is properly leveled when installed.
Check Child Restraint for a snug fit in your car:
While holding Child Restraint near belt path used, pull side to side and forward.
Belt should remain tight and Child Restraint should not move more than
1” (25 mm) from vehicle seat back or side-to-side.
Secure your child:
Refer to the “Securing Child with Harness” section on page 64.
SAFE USE CHECKLIST
6
7
Make sure your child meets the age, weight, and height requirements:
Refer to the “Child Guidelines” section on page 4.
If using Base, make sure Carrier is securely attached to Base:
Refer to the “Install Carrier to Base” section on page 46.
Select a safe seating location in your car:
Refer to the “Vehicle Seating Positions” section on page 16 and 17.
Install Base or Carrier Rear-Facing ONLY:
Refer to the “Child Guidelines” section on page 4.
SAFE USE CHECKLIST
YOUR CHILD’S SAFETY DEPENDS ON YOU! You MUST follow the
detailed instructions in this User Guide to ensure the steps below are
performed correctly!
Ensure that the Child Restraint is properly leveled when installed.
Check Child Restraint for a snug fit in your car:
While holding Child Restraint near belt path used, pull side to side and forward.
Belt should remain tight and Child Restraint should not move more than
1” (25 mm) from vehicle seat back or side-to-side.
Secure your child:
Refer to the “Securing Child with Harness” section on page 64.
SAFE USE CHECKLIST
8
9
IMPORTANT WARNINGS
WARNING
DEATH or SERIOUS INJURY CAN OCCUR
IMPORTANT WARNINGS
WARNING
DEATH or SERIOUS INJURY CAN OCCUR
Secure Child Properly
• Snugly adjust the belts provided with this child restraint around your child. A loose harness could cause the
child to be ejected in a sharp turn, sudden stop or crash, resulting in serious injury or death.
A snug strap should not allow any slack. It lies in a relatively straight line without sagging.
It does not press on the child’s flesh or push the child’s body into an unnatural position.
FAILURE TO FOLLOW THESE INSTRUCTIONS AND THE PRODUCT
LABELS CAN RESULT IN SERIOUS INJURY OR DEATH TO YOUR CHILD.
Take Time to Read This User Guide
• Carefully read and understand all instructions and warnings in this User Guide. Your child’s safety depends on
you knowing how to setup, install and use this Child Restraint properly.
• Before installing this Child Restraint in a vehicle, be sure to also check the vehicle owner’s manual for
information on proper installation.
• NEVER allow others to use this Child Restraint until they have read and understood all instructions in this
User Guide.
Make Sure Child Fits This Child Restraint
• Use only with children who weigh between 4 and 22 lbs (1.8 kg to 10 kg) and whose height is 30 inches
(76 cm) or less.
• Do Not use this Child Restraint if top of child's head is within 1 inch (25 mm) of the top of the headrest.
• Only use the NEWBORN POSITIONER provided for infants who weigh between 4 and 11 lbs (1.8 and 5 kg).
• NEVER use clothing or blankets that interfere with fastening or tightening the harness. An unsecured child
could be ejected in a sharp turn, sudden stop or crash!
To keep child warm, place a blanket over child and restraint AFTER you have properly secured
child in harness.
• ALWAYS check to make sure buckle is securely latched. If buckle separates, child could be killed or seriously injured.
• NEVER leave child unattended. Do not allow children to play in or around the Child Restraint.
• ALWAYS keep child properly secured in harness whenever child is in carrier.
8
9
IMPORTANT WARNINGS
WARNING
DEATH or SERIOUS INJURY CAN OCCUR
IMPORTANT WARNINGS
WARNING
DEATH or SERIOUS INJURY CAN OCCUR
Secure Child Properly
• Snugly adjust the belts provided with this child restraint around your child. A loose harness could cause the
child to be ejected in a sharp turn, sudden stop or crash, resulting in serious injury or death.
A snug strap should not allow any slack. It lies in a relatively straight line without sagging.
It does not press on the child’s flesh or push the child’s body into an unnatural position.
FAILURE TO FOLLOW THESE INSTRUCTIONS AND THE PRODUCT
LABELS CAN RESULT IN SERIOUS INJURY OR DEATH TO YOUR CHILD.
Take Time to Read This User Guide
• Carefully read and understand all instructions and warnings in this User Guide. Your child’s safety depends on
you knowing how to setup, install and use this Child Restraint properly.
• Before installing this Child Restraint in a vehicle, be sure to also check the vehicle owner’s manual for
information on proper installation.
• NEVER allow others to use this Child Restraint until they have read and understood all instructions in this
User Guide.
Make Sure Child Fits This Child Restraint
• Use only with children who weigh between 4 and 22 lbs (1.8 kg to 10 kg) and whose height is 30 inches
(76 cm) or less.
• Do Not use this Child Restraint if top of child's head is within 1 inch (25 mm) of the top of the headrest.
• Only use the NEWBORN POSITIONER provided for infants who weigh between 4 and 11 lbs (1.8 and 5 kg).
• NEVER use clothing or blankets that interfere with fastening or tightening the harness. An unsecured child
could be ejected in a sharp turn, sudden stop or crash!
To keep child warm, place a blanket over child and restraint AFTER you have properly secured
child in harness.
• ALWAYS check to make sure buckle is securely latched. If buckle separates, child could be killed or seriously injured.
• NEVER leave child unattended. Do not allow children to play in or around the Child Restraint.
• ALWAYS keep child properly secured in harness whenever child is in carrier.
10
11
IMPORTANT WARNINGS
WARNING
DEATH or SERIOUS INJURY CAN OCCUR
Install Child Restraint Correctly
IMPORTANT WARNINGS
WARNING
DEATH or SERIOUS INJURY CAN OCCUR
Install Child Restraint Correctly
• BEFORE each use, ALWAYS check to make sure restraint is tightly secured in the vehicle seat.
• NEVER use Child Restraint in a vehicle seating position where it cannot be secured tightly. A loosely
installed child restraint will not protect your child in a crash.
• Never leave carrier or base unsecured in your vehicle even when it is unoccupied. It could injure other
occupants in a sharp turn, sudden stop or crash.
• DO NOT install this child restraint using an inflatable seat belt. The interaction of the inflatable portion
of the vehicle’s belt with this child restraint can result in serious injury or death. Install using LATCH
instead, or move the car seat to a position with a suitable seat belt type.
• To prevent ejection or breathing difficulties, proper recline is required. When installing the Child
Restraint, check the bubble level on the base. Refer to pages 26-27 to make sure your child meets the
requirements.
• Make sure nothing interferes with carrier attachment to base. ALWAYS check attachment.
• ONLY use Chicco KeyFit/KeyFit 30 infant carriers with KeyFit/KeyFit 30 bases.
• DO NOT use Chicco KeyFit 35 or Fit 2 infant carriers with the KeyFit/KeyFit 30 base.
• NEVER PLACE THIS CHILD RESTRAINT IN VEHICLE SEATING LOCATION
WITH A FRONTAL AIR BAG, UNLESS THE AIR BAG CAN BE TURNED OFF.
If the airbag inflates, it can cause serious injury or death to your child. For vehicles
with side air bags, refer to your vehicle owners manual for information on your
child restraint installation.
• ALWAYS install this Child Restraint in a back seat if possible.
According to accident statistics, children are safer when properly restrained in the rear seating
positions rather than in the front seat.
• NEVER install in a rear facing, side facing or on the back of a folded down vehicle seat.
• ALWAYS secure this Child Restraint with the vehicle’s child restraint anchorage system (LATCH) if available
OR with a vehicle seat belt.
• ALWAYS install rear-facing when using this Child Restraint in a vehicle. Your child could be killed or seriously
injured if you install this restraint forward-facing.
10
11
IMPORTANT WARNINGS
WARNING
DEATH or SERIOUS INJURY CAN OCCUR
Install Child Restraint Correctly
IMPORTANT WARNINGS
WARNING
DEATH or SERIOUS INJURY CAN OCCUR
Install Child Restraint Correctly
• BEFORE each use, ALWAYS check to make sure restraint is tightly secured in the vehicle seat.
• NEVER use Child Restraint in a vehicle seating position where it cannot be secured tightly. A loosely
installed child restraint will not protect your child in a crash.
• Never leave carrier or base unsecured in your vehicle even when it is unoccupied. It could injure other
occupants in a sharp turn, sudden stop or crash.
• DO NOT install this child restraint using an inflatable seat belt. The interaction of the inflatable portion
of the vehicle’s belt with this child restraint can result in serious injury or death. Install using LATCH
instead, or move the car seat to a position with a suitable seat belt type.
• To prevent ejection or breathing difficulties, proper recline is required. When installing the Child
Restraint, check the bubble level on the base. Refer to pages 26-27 to make sure your child meets the
requirements.
• Make sure nothing interferes with carrier attachment to base. ALWAYS check attachment.
• ONLY use Chicco KeyFit/KeyFit 30 infant carriers with KeyFit/KeyFit 30 bases.
• DO NOT use Chicco KeyFit 35 or Fit 2 infant carriers with the KeyFit/KeyFit 30 base.
• NEVER PLACE THIS CHILD RESTRAINT IN VEHICLE SEATING LOCATION
WITH A FRONTAL AIR BAG, UNLESS THE AIR BAG CAN BE TURNED OFF.
If the airbag inflates, it can cause serious injury or death to your child. For vehicles
with side air bags, refer to your vehicle owners manual for information on your
child restraint installation.
• ALWAYS install this Child Restraint in a back seat if possible.
According to accident statistics, children are safer when properly restrained in the rear seating
positions rather than in the front seat.
• NEVER install in a rear facing, side facing or on the back of a folded down vehicle seat.
• ALWAYS secure this Child Restraint with the vehicle’s child restraint anchorage system (LATCH) if available
OR with a vehicle seat belt.
• ALWAYS install rear-facing when using this Child Restraint in a vehicle. Your child could be killed or seriously
injured if you install this restraint forward-facing.
12
13
IMPORTANT WARNINGS
WARNING
DEATH or SERIOUS INJURY CAN OCCUR
Ensure Child’s Safety When Using Child Restraint
• NEVER leave child unattended.
• SUFFOCATION HAZARD: Infant carrier can roll over on soft surfaces and suffocate child. NEVER place
carrier on beds, sofas or other soft surfaces.
• STRANGULATION HAZARD: Children have STRANGLED in loose or partially buckled harness straps.
Fully restrain the child even when carrier is used outside the vehicle.
• Fall Hazard: Child's activity can move carrier. NEVER place carrier on counter tops, tables, or any other
elevated surface.
• Fall Hazard: The carrier can fall from the shopping cart. Do not use on shopping cart.
• Do not use the infant carrier if it is damaged or broken.
• BE SURE handle is locked in the “carry position” before lifting carrier by handle. An unlocked handle could
move unexpectedly, causing injury to child.
• ALWAYS check buckle and other parts for hot surfaces. A hot surface could burn child! Cover unoccupied
carrier with blanket when leaving in a vehicle exposed to sunlight or high temperatures..
IMPORTANT WARNINGS
WARNING
DEATH or SERIOUS INJURY CAN OCCUR
Check Condition of Restraint
• DO NOT use if the Harness or LATCH straps are cut, frayed or damaged.
• DO NOT use this Child Restraint if it is more than 6 years old. Check manufacturer’s label on
underside of Child Restraint for the “Do Not Use After” date.
• DO NOT use any accessories, pads or products not included with this Child Restraint, unless
approved by Chicco USA. Doing so will void the warranty of this Child Restraint.
• You MUST replace this Child Restraint if it has been involved in a crash, even if you cannot see
visible damage. A damaged Child Restraint may not protect your child in a future crash.
• Do not modify your Child Restraint.
• For proper removal and installation of the harness straps contact Chicco USA for additional instructions.
• Do not use Child Restraint if any component is damaged, broken, or missing parts.
Call 1-877-424-4226 to find out if the damaged part or parts can be replaced.
12
13
IMPORTANT WARNINGS
WARNING
DEATH or SERIOUS INJURY CAN OCCUR
Ensure Child’s Safety When Using Child Restraint
• NEVER leave child unattended.
• SUFFOCATION HAZARD: Infant carrier can roll over on soft surfaces and suffocate child. NEVER place
carrier on beds, sofas or other soft surfaces.
• STRANGULATION HAZARD: Children have STRANGLED in loose or partially buckled harness straps.
Fully restrain the child even when carrier is used outside the vehicle.
• Fall Hazard: Child's activity can move carrier. NEVER place carrier on counter tops, tables, or any other
elevated surface.
• Fall Hazard: The carrier can fall from the shopping cart. Do not use on shopping cart.
• Do not use the infant carrier if it is damaged or broken.
• BE SURE handle is locked in the “carry position” before lifting carrier by handle. An unlocked handle could
move unexpectedly, causing injury to child.
• ALWAYS check buckle and other parts for hot surfaces. A hot surface could burn child! Cover unoccupied
carrier with blanket when leaving in a vehicle exposed to sunlight or high temperatures..
IMPORTANT WARNINGS
WARNING
DEATH or SERIOUS INJURY CAN OCCUR
Check Condition of Restraint
• DO NOT use if the Harness or LATCH straps are cut, frayed or damaged.
• DO NOT use this Child Restraint if it is more than 6 years old. Check manufacturer’s label on
underside of Child Restraint for the “Do Not Use After” date.
• DO NOT use any accessories, pads or products not included with this Child Restraint, unless
approved by Chicco USA. Doing so will void the warranty of this Child Restraint.
• You MUST replace this Child Restraint if it has been involved in a crash, even if you cannot see
visible damage. A damaged Child Restraint may not protect your child in a future crash.
• Do not modify your Child Restraint.
• For proper removal and installation of the harness straps contact Chicco USA for additional instructions.
• Do not use Child Restraint if any component is damaged, broken, or missing parts.
Call 1-877-424-4226 to find out if the damaged part or parts can be replaced.
14
15
BEST PRACTICES
• Ensure all vehicle occupants are properly restrained before traveling. Unrestrained
occupants can be thrown around and may be seriously injured or seriously injure other
occupants in a sharp turn, sudden stop or crash.
• Do not leave loose objects, such as books, bags, etc., in the back of the vehicle. In the
event of a sharp turn, sudden stop, or crash, loose objects can be thrown around and
possibly cause serious injury to vehicle occupants.
• Cover the Child Restraint when the vehicle is parked in sunlight. Parts of a Child Restraint
can become very hot if left in the sun. Contact with these parts can burn a child’s skin.
Always check the surface of any metal or plastic parts before putting your child in the
Child Restraint.
• To avoid strangulation, Do not allow children to play with vehicle seat belts. If possible,
move unused belts out of reach.
• Do not use anything to raise the Child Restraint off the vehicle seat. In a sharp turn,
sudden stop, or crash, the Child Restraint could slide and potentially cause serious injury.
• Never use a second-hand Child Restraint with an unknown history.
• Never use any accessories that are not included with this child restraint, unless
specifically approved by Chicco. For more information, go to www.chiccousa.com.
• The Head Rest Insert can be used with or without the Newborn Positioner.
NEED HELP?
Need Help Securing Your Child Restraint?
The following sources are available to help ensure your Child Restraint is
properly installed:
• Contact Chicco USA by visiting our website at www.chiccousa.com or
calling our Customer Service 1-877-424-4226. Please have Model and
Serial Number available when you call. These are located on a label on
the bottom of the Child Restraint.
• Refer to your vehicle manual for Child Restraint installation tips.
• Contact a certified Child Passenger Safety Technician in your area by
visiting safercar.gov and select “Find Local Child Seat Help” or call
1-866-SEAT CHECK (1-866-732-8243).
14
15
BEST PRACTICES
• Ensure all vehicle occupants are properly restrained before traveling. Unrestrained
occupants can be thrown around and may be seriously injured or seriously injure other
occupants in a sharp turn, sudden stop or crash.
• Do not leave loose objects, such as books, bags, etc., in the back of the vehicle. In the
event of a sharp turn, sudden stop, or crash, loose objects can be thrown around and
possibly cause serious injury to vehicle occupants.
• Cover the Child Restraint when the vehicle is parked in sunlight. Parts of a Child Restraint
can become very hot if left in the sun. Contact with these parts can burn a child’s skin.
Always check the surface of any metal or plastic parts before putting your child in the
Child Restraint.
• To avoid strangulation, Do not allow children to play with vehicle seat belts. If possible,
move unused belts out of reach.
• Do not use anything to raise the Child Restraint off the vehicle seat. In a sharp turn,
sudden stop, or crash, the Child Restraint could slide and potentially cause serious injury.
• Never use a second-hand Child Restraint with an unknown history.
• Never use any accessories that are not included with this child restraint, unless
specifically approved by Chicco. For more information, go to www.chiccousa.com.
• The Head Rest Insert can be used with or without the Newborn Positioner.
NEED HELP?
Need Help Securing Your Child Restraint?
The following sources are available to help ensure your Child Restraint is
properly installed:
• Contact Chicco USA by visiting our website at www.chiccousa.com or
calling our Customer Service 1-877-424-4226. Please have Model and
Serial Number available when you call. These are located on a label on
the bottom of the Child Restraint.
• Refer to your vehicle manual for Child Restraint installation tips.
• Contact a certified Child Passenger Safety Technician in your area by
visiting safercar.gov and select “Find Local Child Seat Help” or call
1-866-SEAT CHECK (1-866-732-8243).
17
VEHICLE INFORMATION
16
VEHICLE INFORMATION
VEHICLE SEATING POSITIONS VEHICLE SEATING POSITIONS
Some vehicles have no seating positions which are compatible with this Child
Restraint. If in doubt, contact the vehicle manufacturer for assistance. Only
forward-facing vehicle seats can be used with this Child Restraint.
The back seat is the safest place for children 12 and under. See your
vehicle owner’s manual for Child Restraint installation and instructions.
Make sure no more than 4 inches (10cm)
of the Child Restraint base is past the
edge of the vehicle seat.
Do not use on a folded down
vehicle seat back.
WARNING! NEVER PLACE THIS CHILD RESTRAINT IN A
VEHICLE SEATING LOCATION WITH A FRONTAL AIR BAG,
UNLESS THE AIR BAG CAN BE TURNED OFF.
17
VEHICLE INFORMATION
16
VEHICLE INFORMATION
VEHICLE SEATING POSITIONS VEHICLE SEATING POSITIONS
Some vehicles have no seating positions which are compatible with this Child
Restraint. If in doubt, contact the vehicle manufacturer for assistance. Only
forward-facing vehicle seats can be used with this Child Restraint.
The back seat is the safest place for children 12 and under. See your
vehicle owner’s manual for Child Restraint installation and instructions.
Make sure no more than 4 inches (10cm)
of the Child Restraint base is past the
edge of the vehicle seat.
Do not use on a folded down
vehicle seat back.
WARNING! NEVER PLACE THIS CHILD RESTRAINT IN A
VEHICLE SEATING LOCATION WITH A FRONTAL AIR BAG,
UNLESS THE AIR BAG CAN BE TURNED OFF.
19
VEHICLE INFORMATION
18
VEHICLE INFORMATION
For simplest installation use LATCH
Vehicle seat belts differ from vehicle to vehicle. Refer to your vehicle owner’s
manual for specific information about seat belts and their use with Child
Restraints.
Shoulder belt with switchable retractor:
Putting the shoulder belt in the locked/switched mode as the last step is
optional. The shoulder belt Lock-Off replaces the need for the locked/switched
mode. Using the locked/switched mode may cause Child Restraint to tilt.
VEHICLE SEAT BELTS VEHICLE SEAT BELTS
The information in this section only applies to installation with vehicle seat belts.
The following types of vehicle belts MUST NOT be used to install this Child Restraint.
If any of the belt types listed below are in the chosen seating position, choose another
vehicle seating position or use LATCH if available.
1.
Motorized (automatic) vehicle belts.
2.
Door mounted vehicle belts.
4.
Non-Locking (ELR) Lap Belts.
3.
Lap-shoulder Belts with 2 retractors (unless Lap Belt has a “Lock Mode”).
5.
Inflatable seat belts.
1
2 3
4 5
19
VEHICLE INFORMATION
18
VEHICLE INFORMATION
For simplest installation use LATCH
Vehicle seat belts differ from vehicle to vehicle. Refer to your vehicle owner’s
manual for specific information about seat belts and their use with Child
Restraints.
Shoulder belt with switchable retractor:
Putting the shoulder belt in the locked/switched mode as the last step is
optional. The shoulder belt Lock-Off replaces the need for the locked/switched
mode. Using the locked/switched mode may cause Child Restraint to tilt.
VEHICLE SEAT BELTS VEHICLE SEAT BELTS
The information in this section only applies to installation with vehicle seat belts.
The following types of vehicle belts MUST NOT be used to install this Child Restraint.
If any of the belt types listed below are in the chosen seating position, choose another
vehicle seating position or use LATCH if available.
1.
Motorized (automatic) vehicle belts.
2.
Door mounted vehicle belts.
4.
Non-Locking (ELR) Lap Belts.
3.
Lap-shoulder Belts with 2 retractors (unless Lap Belt has a “Lock Mode”).
5.
Inflatable seat belts.
1
2 3
4 5
21
VEHICLE INFORMATION
20
VEHICLE INFORMATION
LATCH = Lower Anchors and Tethers for CHildren
United States Motor Vehicle Safety Standards have defined a system for installing
Child Restraints in vehicles called LATCH. LATCH may ONLY be used IN PLACE
OF vehicle belt if the vehicle is equipped with LATCH anchor points. DO NOT
use both the seat belt and LATCH at the same time. Please refer to the vehicle
owner’s manual for designated LATCH locations in vehicles.
LATCH in the vehicle consists of a top tether anchor point, which is not used with
this child restraint, and two lower anchor points. Some vehicles owner’s manual use
the term “ISOFIX”. LATCH can also be used in vehicle seating positions equipped
with ISOFIX.
If the vehicle is equipped with LATCH, the vehicle lower anchor points may be visible at
the seat crease. If not visible, the seating position may be marked with a symbol (fig. a) or a
colored dot.
WARNING: This Child Restraint is designed to be used with lower LATCH
anchors at the standard spacing (11 inches (28 cm)) ONLY! Refer to vehicle owner’s
manual for information about LATCH and Child Restraint installation positions.
Vehicle
Lower Anchor
Points
Vehicle
Seat Crease
(fig. a)
WHAT IS LATCH
WHAT IS LATCH
21
VEHICLE INFORMATION
20
VEHICLE INFORMATION
LATCH = Lower Anchors and Tethers for CHildren
United States Motor Vehicle Safety Standards have defined a system for installing
Child Restraints in vehicles called LATCH. LATCH may ONLY be used IN PLACE
OF vehicle belt if the vehicle is equipped with LATCH anchor points. DO NOT
use both the seat belt and LATCH at the same time. Please refer to the vehicle
owner’s manual for designated LATCH locations in vehicles.
LATCH in the vehicle consists of a top tether anchor point, which is not used with
this child restraint, and two lower anchor points. Some vehicles owner’s manual use
the term “ISOFIX”. LATCH can also be used in vehicle seating positions equipped
with ISOFIX.
If the vehicle is equipped with LATCH, the vehicle lower anchor points may be visible at
the seat crease. If not visible, the seating position may be marked with a symbol (fig. a) or a
colored dot.
WARNING: This Child Restraint is designed to be used with lower LATCH
anchors at the standard spacing (11 inches (28 cm)) ONLY! Refer to vehicle owner’s
manual for information about LATCH and Child Restraint installation positions.
Vehicle
Lower Anchor
Points
Vehicle
Seat Crease
(fig. a)
WHAT IS LATCH
WHAT IS LATCH
22
23
CHILD RESTRAINT OVERVIEW
CHILD RESTRAINT OVERVIEW
CARRIER COMPONENTS CARRIER COMPONENTS
Buckle
Harness
Straps
Chest Clip
Carry
Handle
Canopy
Harness
Adjuster Button
Harness
Adjuster Strap
Shoulder
Pads
Base Release
Handle
Harness
Straps
Harness
Splitter Plate
Head Rest
Insert
Newborn
Positioner
Seat Belt Guides
(when installing carrier
without the base)
Crotch Strap
Retainer
Harness Strap
Adjustment Slots
Handle
Release
Button
Headrest
Insert Straps
22
23
CHILD RESTRAINT OVERVIEW
CHILD RESTRAINT OVERVIEW
CARRIER COMPONENTS CARRIER COMPONENTS
Buckle
Harness
Straps
Chest Clip
Carry
Handle
Canopy
Harness
Adjuster Button
Harness
Adjuster Strap
Shoulder
Pads
Base Release
Handle
Harness
Straps
Harness
Splitter Plate
Head Rest
Insert
Newborn
Positioner
Seat Belt Guides
(when installing carrier
without the base)
Crotch Strap
Retainer
Harness Strap
Adjustment Slots
Handle
Release
Button
Headrest
Insert Straps
24
25
CHILD RESTRAINT OVERVIEW
CHILD RESTRAINT OVERVIEW
LATCH
Connector
BASE AND LATCH COMPONENTS BASE AND LATCH COMPONENTS
Recline
Foot
LATCH
Release
Lever
Carrier
Attachment
Hook
Shoulder Belt
Lock-Off
Bubble
Level
Indicator
Foot
Adjuster
Buttons
LATCH
Pull Strap
User Guide
Storage
(Inside Base)
PAGE INTENTIONALLY LEFT BLANK
24
25
CHILD RESTRAINT OVERVIEW
CHILD RESTRAINT OVERVIEW
LATCH
Connector
BASE AND LATCH COMPONENTS BASE AND LATCH COMPONENTS
Recline
Foot
LATCH
Release
Lever
Carrier
Attachment
Hook
Shoulder Belt
Lock-Off
Bubble
Level
Indicator
Foot
Adjuster
Buttons
LATCH
Pull Strap
User Guide
Storage
(Inside Base)
PAGE INTENTIONALLY LEFT BLANK
26
27
CHILD RESTRAINT OVERVIEW
CHILD RESTRAINT OVERVIEW
CHILD REQUIREMENTS
CHILD REQUIREMENTS
WEIGHT REQUIREMENTS:
4 – 22 lbs (1.8 – 10 kg)
Use with children:
• Who weigh between 4 and 22 lbs (1.8 –10 kg).
• And height is less than 30 inches (76 cm).
• And top of head is at least 1 inch (25 mm) below
top of seat back.
• When Harness Straps can be positioned at
or just below the child’s shoulders*.
See Adjusting Harness Height
on page 60.
*
• Base installation continued on page 28.
• Without Base Installation continued on page 50.
Install Child Restraint:
WEIGHT REQUIREMENTS
4 lbs. 22 lbs.
(1.8 kg) (10 kg)
For premature infants, you must consult the infant's doctor before
using this Child Restraint. A premature infant may have difficulty breathing
or have other medical problems when placed in a seated position.
26
27
CHILD RESTRAINT OVERVIEW
CHILD RESTRAINT OVERVIEW
CHILD REQUIREMENTS
CHILD REQUIREMENTS
WEIGHT REQUIREMENTS:
4 – 22 lbs (1.8 – 10 kg)
Use with children:
• Who weigh between 4 and 22 lbs (1.8 –10 kg).
• And height is less than 30 inches (76 cm).
• And top of head is at least 1 inch (25 mm) below
top of seat back.
• When Harness Straps can be positioned at
or just below the child’s shoulders*.
See Adjusting Harness Height
on page 60.
*
• Base installation continued on page 28.
• Without Base Installation continued on page 50.
Install Child Restraint:
WEIGHT REQUIREMENTS
4 lbs. 22 lbs.
(1.8 kg) (10 kg)
For premature infants, you must consult the infant's doctor before
using this Child Restraint. A premature infant may have difficulty breathing
or have other medical problems when placed in a seated position.
28
29
BASE INSTALLATION
BASE INSTALLATION
INSTALL WITH BASE SETUP
INSTALL WITH BASE SETUP
See page 16 for “Vehicle Seating Positions” before installing. Make
sure the vehicle is on a level surface. Place Base on selected vehicle
seat. Make sure it is not blocking the vehicle seat belt buckle.
Locate the Bubble Level Indicator and adjust the Recline Foot by pushing in on
both Foot Adjuster buttons and lifting or lowering the base until the Bubble
falls between the arrows on the Bubble Level Indicator (2b).
1
2
LEVEL
SLO PE
• LATCH installation continued on page 30.
• Lap-Shoulder Belt installation continued on page 36.
• Lap Belt Only installation continued on page 42.
Installation Options:
2b
Infants may have difficulty breathing when in a sitting position.
Make sure the seat is reclined properly so that your child’s head does
not fall forward. Failure to properly recline the Child Restraint
could increase the child’s risk of serious injury or death.
28
29
BASE INSTALLATION
BASE INSTALLATION
INSTALL WITH BASE SETUP
INSTALL WITH BASE SETUP
See page 16 for “Vehicle Seating Positions” before installing. Make
sure the vehicle is on a level surface. Place Base on selected vehicle
seat. Make sure it is not blocking the vehicle seat belt buckle.
Locate the Bubble Level Indicator and adjust the Recline Foot by pushing in on
both Foot Adjuster buttons and lifting or lowering the base until the Bubble
falls between the arrows on the Bubble Level Indicator (2b).
1
2
LEVEL
SLO PE
• LATCH installation continued on page 30.
• Lap-Shoulder Belt installation continued on page 36.
• Lap Belt Only installation continued on page 42.
Installation Options:
2b
Infants may have difficulty breathing when in a sitting position.
Make sure the seat is reclined properly so that your child’s head does
not fall forward. Failure to properly recline the Child Restraint
could increase the child’s risk of serious injury or death.
30
31
BASE INSTALLATION
BASE INSTALLATION
INSTALL USING LATCH INSTALL USING LATCH
1 2
Pull up on the LATCH Release Lever and loosen LATCH straps to their full
length.
Locate the LATCH Connector storage compartments. Remove both LATCH
Connectors.
1
2
Store LATCH Connectors properly in the compartments when
not using for installation - See page 75.
When installing with LATCH, the unused seat belt should not
be buckled behind the Child Restraint System as this will engage
the inflatable portion of the belt.
30
31
BASE INSTALLATION
BASE INSTALLATION
INSTALL USING LATCH INSTALL USING LATCH
1 2
Pull up on the LATCH Release Lever and loosen LATCH straps to their full
length.
Locate the LATCH Connector storage compartments. Remove both LATCH
Connectors.
1
2
Store LATCH Connectors properly in the compartments when
not using for installation - See page 75.
When installing with LATCH, the unused seat belt should not
be buckled behind the Child Restraint System as this will engage
the inflatable portion of the belt.
32
33
BASE INSTALLATION
BASE INSTALLATION
INSTALL USING LATCH INSTALL USING LATCH
4
Locate the LATCH anchor bars in your vehicle. Attach both LATCH
Connectors to the vehicle LATCH anchor bars.
Tighten LATCH straps by pulling up on LATCH Pull Strap while pressing Base
firmly into vehicle seat.
3
4
3
32
33
BASE INSTALLATION
BASE INSTALLATION
INSTALL USING LATCH INSTALL USING LATCH
4
Locate the LATCH anchor bars in your vehicle. Attach both LATCH
Connectors to the vehicle LATCH anchor bars.
Tighten LATCH straps by pulling up on LATCH Pull Strap while pressing Base
firmly into vehicle seat.
3
4
3
34
35
BASE INSTALLATION
BASE INSTALLATION
Roll LATCH Pull Strap and store in Pull Strap Storage Slot, as shown.
5
INSTALL USING LATCH INSTALL USING LATCH
5
CHECK YOUR WORK
Hold Base at each side and pull side to side and forward. Base should not
move more than 1” (25 mm) from vehicle seat back or side-to-side.
Check installation before every use!
• Installation continued on page 46.
Install Child Restraint:
CHECK YOUR WORK
34
35
BASE INSTALLATION
BASE INSTALLATION
Roll LATCH Pull Strap and store in Pull Strap Storage Slot, as shown.
5
INSTALL USING LATCH INSTALL USING LATCH
5
CHECK YOUR WORK
Hold Base at each side and pull side to side and forward. Base should not
move more than 1” (25 mm) from vehicle seat back or side-to-side.
Check installation before every use!
• Installation continued on page 46.
Install Child Restraint:
CHECK YOUR WORK
36
37
BASE INSTALLATION
BASE INSTALLATION
INSTALL USING LAP-SHOULDER BELT
INSTALL USING LAP-SHOULDER BELT
Thread vehicle seat belt up through the belt path on the side of the Base.
Pull vehicle seat belt down through the vehicle seat belt path on opposite
side of the Base. Buckle the vehicle seat belt.
2
1
1 2
Belt
Path
CLICK!
36
37
BASE INSTALLATION
BASE INSTALLATION
INSTALL USING LAP-SHOULDER BELT
INSTALL USING LAP-SHOULDER BELT
Thread vehicle seat belt up through the belt path on the side of the Base.
Pull vehicle seat belt down through the vehicle seat belt path on opposite
side of the Base. Buckle the vehicle seat belt.
2
1
1 2
Belt
Path
CLICK!
38
39
BASE INSTALLATION
BASE INSTALLATION
While pushing down on the Base, pull up on the vehicle shoulder belt to
remove all slack from the vehicle lap belt.
3
INSTALL USING LAP-SHOULDER BELT
INSTALL USING LAP-SHOULDER BELT
3
38
39
BASE INSTALLATION
BASE INSTALLATION
While pushing down on the Base, pull up on the vehicle shoulder belt to
remove all slack from the vehicle lap belt.
3
INSTALL USING LAP-SHOULDER BELT
INSTALL USING LAP-SHOULDER BELT
3
40
41
BASE INSTALLATION
BASE INSTALLATION
CHECK YOUR WORK
While holding the shoulder belt tight, slide the shoulder belt strap
firmly into Shoulder Belt Lock-Off. Always use the Lock-Off on the
opposite side of where the vehicle seat belt is buckled.
Do NOT pull on shoulder belt after it is positioned in Lock-Off.
This could damage the Lock-Off and/or the vehicle belt
INSTALL USING LAP-SHOULDER BELT
4
CHECK YOUR WORK
Hold Base at each side and pull side to side and forward. Base should not
move more than 1” (25 mm) from vehicle seat back or side-to-side.
Check installation before every use!
4
INSTALL USING LAP-SHOULDER BELT
• Installation continued on page 46.
Install Child Restraint:
40
41
BASE INSTALLATION
BASE INSTALLATION
CHECK YOUR WORK
While holding the shoulder belt tight, slide the shoulder belt strap
firmly into Shoulder Belt Lock-Off. Always use the Lock-Off on the
opposite side of where the vehicle seat belt is buckled.
Do NOT pull on shoulder belt after it is positioned in Lock-Off.
This could damage the Lock-Off and/or the vehicle belt
INSTALL USING LAP-SHOULDER BELT
4
CHECK YOUR WORK
Hold Base at each side and pull side to side and forward. Base should not
move more than 1” (25 mm) from vehicle seat back or side-to-side.
Check installation before every use!
4
INSTALL USING LAP-SHOULDER BELT
• Installation continued on page 46.
Install Child Restraint:
42
43
BASE INSTALLATION
BASE INSTALLATION
INSTALL USING LAP BELT ONLY
INSTALL USING LAP BELT ONLY
Thread vehicle seat belt up through the belt path on the side of the Base.
Pull vehicle seat belt down through the vehicle seat belt path on opposite
side of the Base. Buckle the vehicle seat belt.
2
1
1 2
Belt
Path
CLICK!
42
43
BASE INSTALLATION
BASE INSTALLATION
INSTALL USING LAP BELT ONLY
INSTALL USING LAP BELT ONLY
Thread vehicle seat belt up through the belt path on the side of the Base.
Pull vehicle seat belt down through the vehicle seat belt path on opposite
side of the Base. Buckle the vehicle seat belt.
2
1
1 2
Belt
Path
CLICK!
44
45
BASE INSTALLATION
BASE INSTALLATION
INSTALL USING LAP BELT ONLY
INSTALL USING LAP BELT ONLY
While pushing down on the Base, pull up on the loose end of the
vehicle lap belt to remove all slack.
3
3
CHECK YOUR WORK
Hold Base at each side and pull side to side and forward. Base should not
move more than 1” (25 mm) from vehicle seat back or side-to-side.
Check installation before every use!
• Installation continued on page 46.
Install Child Restraint:
CHECK YOUR WORK
44
45
BASE INSTALLATION
BASE INSTALLATION
INSTALL USING LAP BELT ONLY
INSTALL USING LAP BELT ONLY
While pushing down on the Base, pull up on the loose end of the
vehicle lap belt to remove all slack.
3
3
CHECK YOUR WORK
Hold Base at each side and pull side to side and forward. Base should not
move more than 1” (25 mm) from vehicle seat back or side-to-side.
Check installation before every use!
• Installation continued on page 46.
Install Child Restraint:
CHECK YOUR WORK
46
47
BASE INSTALLATION
BASE INSTALLATION
1
INSTALL CARRIER TO BASE
Insert the Carrier into the Base.
Push down on the Carrier to make sure it locks onto the Carrier
Attachment Hooks on the Base.
1
INSTALL CARRIER TO BASE
2
2
Carrier
Attachment
Hook
46
47
BASE INSTALLATION
BASE INSTALLATION
1
INSTALL CARRIER TO BASE
Insert the Carrier into the Base.
Push down on the Carrier to make sure it locks onto the Carrier
Attachment Hooks on the Base.
1
INSTALL CARRIER TO BASE
2
2
Carrier
Attachment
Hook
48
49
BASE INSTALLATION
BASE INSTALLATION
INSTALL CARRIER TO BASE
Check to make sure the Carrier is securely attached to the Base.
3
INSTALL CARRIER TO BASE
3
ALWAYS lift up on Carrier to verify it is properly attached to the Base.
CHECK YOUR WORK
Hold Base at each side and pull side to side and forward. Child Restraint
should not move more than 1” (25 mm) from vehicle seat back or
side-to-side.
Make sure Child Restraint is level by confirming that the bubble on the
level indicator is between the level lines. Make sure infant’s head does
not fall forward. If necessary, re-adjust recline and repeat installation
steps to make sure Child Restraint is installed properly.
Check installation before every use!
48
49
BASE INSTALLATION
BASE INSTALLATION
INSTALL CARRIER TO BASE
Check to make sure the Carrier is securely attached to the Base.
3
INSTALL CARRIER TO BASE
3
ALWAYS lift up on Carrier to verify it is properly attached to the Base.
CHECK YOUR WORK
Hold Base at each side and pull side to side and forward. Child Restraint
should not move more than 1” (25 mm) from vehicle seat back or
side-to-side.
Make sure Child Restraint is level by confirming that the bubble on the
level indicator is between the level lines. Make sure infant’s head does
not fall forward. If necessary, re-adjust recline and repeat installation
steps to make sure Child Restraint is installed properly.
Check installation before every use!
50
51
WITHOUT BASE INSTALLATION
WITHOUT BASE INSTALLATION
INSTALL WITHOUT BASE SETUP INSTALL WITHOUT BASE SETUP
Position Child Restraint so that the Level Line (located on the seat label) is
LEVEL with the ground.
If needed, use a rolled up towel to help level the Child Restraint properly.
1
NEVER install Child Restraint without Base using a non-locking vehicle belt. The installation
will NOT be secure. Refer to your vehicle owner's manual for detailed vehicle belt information.
LEVEL
SLO PE
• Lap-Shoulder Belt installation continued on page 52.
• Lap Belt Only installation continued on page 56.
Installation Options:
2
2
Infants may have difficulty breathing when in a sitting position. Make sure the seat
is reclined properly so that your child’s head does not fall forward. Failure to properly
recline the Child Restraint could increase the child’s risk of serious injury or death.
Level Line
(Seat Label)
See page 16 for “Vehicle Seating Positions” before installing. Make sure
the vehicle is on a level surface. Place Child Restraint on selected vehicle
seat with child properly secured in Child Restraint
(See securing your child
on page 64)
. Make sure it is not blocking the vehicle seat belt buckle.
3
3
50
51
WITHOUT BASE INSTALLATION
WITHOUT BASE INSTALLATION
INSTALL WITHOUT BASE SETUP INSTALL WITHOUT BASE SETUP
Position Child Restraint so that the Level Line (located on the seat label) is
LEVEL with the ground.
If needed, use a rolled up towel to help level the Child Restraint properly.
1
NEVER install Child Restraint without Base using a non-locking vehicle belt. The installation
will NOT be secure. Refer to your vehicle owner's manual for detailed vehicle belt information.
LEVEL
SLO PE
• Lap-Shoulder Belt installation continued on page 52.
• Lap Belt Only installation continued on page 56.
Installation Options:
2
2
Infants may have difficulty breathing when in a sitting position. Make sure the seat
is reclined properly so that your child’s head does not fall forward. Failure to properly
recline the Child Restraint could increase the child’s risk of serious injury or death.
Level Line
(Seat Label)
See page 16 for “Vehicle Seating Positions” before installing. Make sure
the vehicle is on a level surface. Place Child Restraint on selected vehicle
seat with child properly secured in Child Restraint
(See securing your child
on page 64)
. Make sure it is not blocking the vehicle seat belt buckle.
3
3
52
53
WITHOUT BASE INSTALLATION
WITHOUT BASE INSTALLATION
INSTALL USING LAP-SHOULDER BELT
INSTALL USING LAP-SHOULDER BELT
Thread vehicle seat belt up and slide into the Seat Belt Guide on the side of
the Child Restraint.
Pull vehicle seat belt down and slide into the Seat Belt Guide on opposite
side of the Child Restraint. Buckle the vehicle seat belt. Pull out all of the
shoulder belt webbing and activate the locking mode of the vehicle belt.
If belt does not lock, do not use that seating position to install the carrier.
1
2
21
CLICK!
Seat Belt
Guide
52
53
WITHOUT BASE INSTALLATION
WITHOUT BASE INSTALLATION
INSTALL USING LAP-SHOULDER BELT
INSTALL USING LAP-SHOULDER BELT
Thread vehicle seat belt up and slide into the Seat Belt Guide on the side of
the Child Restraint.
Pull vehicle seat belt down and slide into the Seat Belt Guide on opposite
side of the Child Restraint. Buckle the vehicle seat belt. Pull out all of the
shoulder belt webbing and activate the locking mode of the vehicle belt.
If belt does not lock, do not use that seating position to install the carrier.
1
2
21
CLICK!
Seat Belt
Guide
54
55
WITHOUT BASE INSTALLATION
WITHOUT BASE INSTALLATION
INSTALL USING LAP-SHOULDER BELT
INSTALL USING LAP-SHOULDER BELT
While pushing down on the Carrier, pull up on the vehicle shoulder belt to
remove all slack from vehicle lap belt.
3
Put the vehicle seat belt in the locked mode, see vehicle owner's manual for more
information. A tightly rolled towel may be used under the front edge of the
Carrier if needed to adjust the angle of the Carrier. Angle is correct when level line
on Carrier is level with ground.
CHECK YOUR WORK
Hold Child Restraint at each side and pull side to side and forward.
Child Restraint should not move more than 1” (25 mm) from vehicle seat
back or side-to-side.
Make sure Child Restraint is level. Make sure infant’s head does not fall
forward. If necessary re-adjust recline and repeat installation steps to
make sure Child Restraint is installed properly.
Check installation before every use!
3
CHECK YOUR WORK
54
55
WITHOUT BASE INSTALLATION
WITHOUT BASE INSTALLATION
INSTALL USING LAP-SHOULDER BELT
INSTALL USING LAP-SHOULDER BELT
While pushing down on the Carrier, pull up on the vehicle shoulder belt to
remove all slack from vehicle lap belt.
3
Put the vehicle seat belt in the locked mode, see vehicle owner's manual for more
information. A tightly rolled towel may be used under the front edge of the
Carrier if needed to adjust the angle of the Carrier. Angle is correct when level line
on Carrier is level with ground.
CHECK YOUR WORK
Hold Child Restraint at each side and pull side to side and forward.
Child Restraint should not move more than 1” (25 mm) from vehicle seat
back or side-to-side.
Make sure Child Restraint is level. Make sure infant’s head does not fall
forward. If necessary re-adjust recline and repeat installation steps to
make sure Child Restraint is installed properly.
Check installation before every use!
3
CHECK YOUR WORK
56
57
WITHOUT BASE INSTALLATION
WITHOUT BASE INSTALLATION
CLICK!
Seat Belt
Guide
INSTALL USING LAP BELT ONLY
INSTALL USING LAP BELT ONLY
Thread vehicle seat belt up and slide into the Seat Belt Guide on the side of
the Child Restraint.
Pull vehicle seat belt down and slide into the Seat Belt Guide on opposite
side of the Child Restraint. Buckle the vehicle seat belt.
1
2
21
56
57
WITHOUT BASE INSTALLATION
WITHOUT BASE INSTALLATION
CLICK!
Seat Belt
Guide
INSTALL USING LAP BELT ONLY
INSTALL USING LAP BELT ONLY
Thread vehicle seat belt up and slide into the Seat Belt Guide on the side of
the Child Restraint.
Pull vehicle seat belt down and slide into the Seat Belt Guide on opposite
side of the Child Restraint. Buckle the vehicle seat belt.
1
2
21
58
59
WITHOUT BASE INSTALLATION
WITHOUT BASE INSTALLATION
INSTALL USING LAP BELT ONLY
INSTALL USING LAP BELT ONLY
While pushing down on the Child Restraint, pull up on the loose end of the
vehicle lap belt to remove all slack.
3
Put the vehicle seat belt in the locked mode, see vehicle owner's manual for more
information. A tightly rolled towel may be used under the front edge of the
Carrier if needed to adjust the angle of the Carrier. Angle is correct when level line
on Carrier is level with ground.
CHECK YOUR WORK
Hold Child Restraint at each side and pull side to side and forward.
Child Restraint should not move more than 1” (25 mm) from vehicle seat
back or side-to-side.
Make sure Child Restraint is level. Make sure infant’s head does not fall
forward. If necessary re-adjust recline and repeat installation steps to
make sure Child Restraint is installed properly.
Check installation before every use!
3
CHECK YOUR WORK
58
59
WITHOUT BASE INSTALLATION
WITHOUT BASE INSTALLATION
INSTALL USING LAP BELT ONLY
INSTALL USING LAP BELT ONLY
While pushing down on the Child Restraint, pull up on the loose end of the
vehicle lap belt to remove all slack.
3
Put the vehicle seat belt in the locked mode, see vehicle owner's manual for more
information. A tightly rolled towel may be used under the front edge of the
Carrier if needed to adjust the angle of the Carrier. Angle is correct when level line
on Carrier is level with ground.
CHECK YOUR WORK
Hold Child Restraint at each side and pull side to side and forward.
Child Restraint should not move more than 1” (25 mm) from vehicle seat
back or side-to-side.
Make sure Child Restraint is level. Make sure infant’s head does not fall
forward. If necessary re-adjust recline and repeat installation steps to
make sure Child Restraint is installed properly.
Check installation before every use!
3
CHECK YOUR WORK
60
61
SECURING YOUR CHILD
SECURING YOUR CHILD
ADJUSTING HARNESS HEIGHT
With child seated correctly in the Carrier, resting against back and
bottom of carrier and not slouched, locate the Harness Strap Adjustment
Slot closest to AT or JUST BELOW top of child's shoulders.
Remove your child from the carrier and loosen the Harness Straps. Turn
the Carrier over and locate the splitter plate. Unhook one Harness Strap
from the Splitter Plate.
1
2
ADJUSTING HARNESS HEIGHT
21
Splitter
Plate
AT OR JUST BELOW
*
60
61
SECURING YOUR CHILD
SECURING YOUR CHILD
ADJUSTING HARNESS HEIGHT
With child seated correctly in the Carrier, resting against back and
bottom of carrier and not slouched, locate the Harness Strap Adjustment
Slot closest to AT or JUST BELOW top of child's shoulders.
Remove your child from the carrier and loosen the Harness Straps. Turn
the Carrier over and locate the splitter plate. Unhook one Harness Strap
from the Splitter Plate.
1
2
ADJUSTING HARNESS HEIGHT
21
Splitter
Plate
AT OR JUST BELOW
*
62
63
SECURING YOUR CHILD
SECURING YOUR CHILD
ADJUSTING HARNESS HEIGHT
Pull Harness Strap out through the front of the Carrier. Then re-thread the
Harness Strap through the desired Harness Strap Adjustment Slot.
Re-attach Harness Strap to the Splitter Plate. Repeat steps 1-4 of
Adjusting Harness Height for the other Harness Strap. Make sure both
Harness Straps are at positioned at the same height, as shown.
3
4
ADJUSTING HARNESS HEIGHT
43
WARNING - Make sure Harness Straps are NOT twisted and
both Harness Straps are securely attached to the Splitter Plate.
62
63
SECURING YOUR CHILD
SECURING YOUR CHILD
ADJUSTING HARNESS HEIGHT
Pull Harness Strap out through the front of the Carrier. Then re-thread the
Harness Strap through the desired Harness Strap Adjustment Slot.
Re-attach Harness Strap to the Splitter Plate. Repeat steps 1-4 of
Adjusting Harness Height for the other Harness Strap. Make sure both
Harness Straps are at positioned at the same height, as shown.
3
4
ADJUSTING HARNESS HEIGHT
43
WARNING - Make sure Harness Straps are NOT twisted and
both Harness Straps are securely attached to the Splitter Plate.
64
65
SECURING YOUR CHILD
SECURING YOUR CHILD
SECURING CHILD WITH HARNESS SECURING CHILD WITH HARNESS
Loosen harness by pressing the Adjuster Button and pulling out on both
Harness Straps.
Press the button on the buckle and release both buckle tongues.
Separate chest clip and spread Harness Straps apart. Place child in carrier
in seated position.
1
2
3
For a better fit in the Carrier with smaller infants, the provided Newborn
Positioner may be needed. See page 76 for more details.
2
1
3
Child must be resting against back and bottom of carrier. Make sure
child is not slouched.
64
65
SECURING YOUR CHILD
SECURING YOUR CHILD
SECURING CHILD WITH HARNESS SECURING CHILD WITH HARNESS
Loosen harness by pressing the Adjuster Button and pulling out on both
Harness Straps.
Press the button on the buckle and release both buckle tongues.
Separate chest clip and spread Harness Straps apart. Place child in carrier
in seated position.
1
2
3
For a better fit in the Carrier with smaller infants, the provided Newborn
Positioner may be needed. See page 76 for more details.
2
1
3
Child must be resting against back and bottom of carrier. Make sure
child is not slouched.
66
67
SECURING YOUR CHILD
SECURING YOUR CHILD
SECURING CHILD WITH HARNESS
Make sure harness straps are AT or JUST BELOW top of child's
shoulders. If not, refer to page 60 for Adjusting Harness Height.
Pull Harness Straps over child's shoulders and pull waist straps around
their waist.
4
SECURING CHILD WITH HARNESS
AT OR JUST BELOW
4 5
NEVER use clothing or blankets that interfere with fastening or
tightening the harness. An unsecured child could be ejected in a
sharp turn, sudden stop or crash!
5
Never secure child in Carrier with child dressed in bulky garments or heavy clothing.
Heavy clothing can prevent harness from being properly tightened around child.
*
66
67
SECURING YOUR CHILD
SECURING YOUR CHILD
SECURING CHILD WITH HARNESS
Make sure harness straps are AT or JUST BELOW top of child's
shoulders. If not, refer to page 60 for Adjusting Harness Height.
Pull Harness Straps over child's shoulders and pull waist straps around
their waist.
4
SECURING CHILD WITH HARNESS
AT OR JUST BELOW
4 5
NEVER use clothing or blankets that interfere with fastening or
tightening the harness. An unsecured child could be ejected in a
sharp turn, sudden stop or crash!
5
Never secure child in Carrier with child dressed in bulky garments or heavy clothing.
Heavy clothing can prevent harness from being properly tightened around child.
*
68
69
SECURING YOUR CHILD
SECURING YOUR CHILD
Insert each Buckle Tongue into Harness Buckle; listen for a click (6a). Pull
up firmly on both Buckle Tongues to make sure that they are securely
latched (6b).
Fasten Chest Clip by snapping both sides together.
SECURING CHILD WITH HARNESS SECURING CHILD WITH HARNESS
6
6b6a
CLICK!
7
7
CLICK!
Harness Straps must be laying flat, free of twists and on top of child's shoulders.
68
69
SECURING YOUR CHILD
SECURING YOUR CHILD
Insert each Buckle Tongue into Harness Buckle; listen for a click (6a). Pull
up firmly on both Buckle Tongues to make sure that they are securely
latched (6b).
Fasten Chest Clip by snapping both sides together.
SECURING CHILD WITH HARNESS SECURING CHILD WITH HARNESS
6
6b6a
CLICK!
7
7
CLICK!
Harness Straps must be laying flat, free of twists and on top of child's shoulders.
70
71
SECURING YOUR CHILD
SECURING YOUR CHILD
Tighten the harness by pulling slowly on Harness Adjuster Strap while
pulling up on both shoulder straps to remove all slack from below (8a).
Make sure the Harness Straps are snug on child. If you can pinch a fold in
the Harness Strap at the child’s shoulders, harness is too loose (8b). If the
Harness Straps are too loose pull the Harness Adjuster Strap more.
Move the Shoulder Pads up to the child’s shoulders. Slide Chest Clip up to
center of child’s chest, level with the armpits.
8
9
8a
9
SECURING CHILD WITH HARNESS SECURING CHILD WITH HARNESS
8b
Pull excess strap up through buckle tongues so that harness is snug around
child's thighs.
WARNING - If harness is not snug around your child, child could be ejected
in a sharp turn, sudden stop or crash resulting in serious injury or death.
70
71
SECURING YOUR CHILD
SECURING YOUR CHILD
Tighten the harness by pulling slowly on Harness Adjuster Strap while
pulling up on both shoulder straps to remove all slack from below (8a).
Make sure the Harness Straps are snug on child. If you can pinch a fold in
the Harness Strap at the child’s shoulders, harness is too loose (8b). If the
Harness Straps are too loose pull the Harness Adjuster Strap more.
Move the Shoulder Pads up to the child’s shoulders. Slide Chest Clip up to
center of child’s chest, level with the armpits.
8
9
8a
9
SECURING CHILD WITH HARNESS SECURING CHILD WITH HARNESS
8b
Pull excess strap up through buckle tongues so that harness is snug around
child's thighs.
WARNING - If harness is not snug around your child, child could be ejected
in a sharp turn, sudden stop or crash resulting in serious injury or death.
72
73
SECURING YOUR CHILD
SECURING YOUR CHILD
Check the position of Chest Clip: Chest Clip should be centered on the child’s chest, level
with the armpits.
Never secure child in Carrier with child dressed in bulky garments or heavy clothing.
Heavy clothing can prevent harness from being properly tightened around child.
Never secure child in Carrier with child wrapped in a blanket. To keep child warm, place a
blanket over child AFTER you have properly secured and tightened harness around child.
Harness Straps must be snug. If you can pinch a fold in the strap at the shoulders, the
harness is too loose. A snug strap should not allow any slack. It lies in a relatively straight
line without sagging. It does not press on the child’s flesh or push the child’s body into an
unnatural position.
To ensure a better fit for smaller infants, the Newborn Positioner may be needed. Never
place extra padding under or behind the child. Only use the Newborn Positioner. Never use
Newborn Positioner if child weighs more than 11 pounds (5 kg).
Straps must lay flat, free of twists and centered on top of the child’s shoulders.
Check the height of the Harness Straps: Position the Harness Straps
at or just below the child’s shoulders.
SECURING CHILD CHECKLIST SECURING CHILD CHECKLIST
*
NO Bulky Clothing
72
73
SECURING YOUR CHILD
SECURING YOUR CHILD
Check the position of Chest Clip: Chest Clip should be centered on the child’s chest, level
with the armpits.
Never secure child in Carrier with child dressed in bulky garments or heavy clothing.
Heavy clothing can prevent harness from being properly tightened around child.
Never secure child in Carrier with child wrapped in a blanket. To keep child warm, place a
blanket over child AFTER you have properly secured and tightened harness around child.
Harness Straps must be snug. If you can pinch a fold in the strap at the shoulders, the
harness is too loose. A snug strap should not allow any slack. It lies in a relatively straight
line without sagging. It does not press on the child’s flesh or push the child’s body into an
unnatural position.
To ensure a better fit for smaller infants, the Newborn Positioner may be needed. Never
place extra padding under or behind the child. Only use the Newborn Positioner. Never use
Newborn Positioner if child weighs more than 11 pounds (5 kg).
Straps must lay flat, free of twists and centered on top of the child’s shoulders.
Check the height of the Harness Straps: Position the Harness Straps
at or just below the child’s shoulders.
SECURING CHILD CHECKLIST SECURING CHILD CHECKLIST
*
NO Bulky Clothing
ADDITIONAL INFORMATION
74
75
ADDITIONAL INFORMATION
BASE RELEASE HANDLE
LATCH STORAGE
1
Insert LATCH Connectors into the LATCH Connector storage compartments.
Pull on the LATCH Pull Strap to secure LATCH Connectors in the
compartments.
Roll LATCH Pull Strap and store in Pull Strap Storage Slot.
3
2
Store both LATCH Connector in compartments on either side of the Base when not in use.
1 2 3
Store LATCH Connectors properly in the compartments when
not using for installation.
RELEASE CARRIER FROM BASE:
To unhook the Carrier from the Base, squeeze the Base Release Handle
on the back of the Carrier then lift up on the Carry Handle.
ADDITIONAL INFORMATION
74
75
ADDITIONAL INFORMATION
BASE RELEASE HANDLE
LATCH STORAGE
1
Insert LATCH Connectors into the LATCH Connector storage compartments.
Pull on the LATCH Pull Strap to secure LATCH Connectors in the
compartments.
Roll LATCH Pull Strap and store in Pull Strap Storage Slot.
3
2
Store both LATCH Connector in compartments on either side of the Base when not in use.
1 2 3
Store LATCH Connectors properly in the compartments when
not using for installation.
RELEASE CARRIER FROM BASE:
To unhook the Carrier from the Base, squeeze the Base Release Handle
on the back of the Carrier then lift up on the Carry Handle.
ADDITIONAL INFORMATION
76
77
ADDITIONAL INFORMATION
NEWBORN POSITIONER
To ensure a better fit for smaller infants the Newborn Positioner may be needed.
Do NOT use any other newborn positioner or pillows. Only use the one provided
by Chicco for this Child Restraint.
Place the Newborn Positioner in the Carrier seat. Then pull the Buckle
through slot in the bottom of Newborn Positioner.
Pull both Harness Straps over the side panels of Newborn Positioner.
Push Newborn Positioner firmly into Carrier to make sure it is properly
positioned against the back of the seating area.
1
2
3
NEWBORN POSITIONER
WARNING
- Use the NEWBORN POSITIONER provided
for infants who weigh between 4 and 11 lbs (1.8 and 5 kg).
21
3
ADDITIONAL INFORMATION
76
77
ADDITIONAL INFORMATION
NEWBORN POSITIONER
To ensure a better fit for smaller infants the Newborn Positioner may be needed.
Do NOT use any other newborn positioner or pillows. Only use the one provided
by Chicco for this Child Restraint.
Place the Newborn Positioner in the Carrier seat. Then pull the Buckle
through slot in the bottom of Newborn Positioner.
Pull both Harness Straps over the side panels of Newborn Positioner.
Push Newborn Positioner firmly into Carrier to make sure it is properly
positioned against the back of the seating area.
1
2
3
NEWBORN POSITIONER
WARNING
- Use the NEWBORN POSITIONER provided
for infants who weigh between 4 and 11 lbs (1.8 and 5 kg).
21
3
ADDITIONAL INFORMATION
78
79
ADDITIONAL INFORMATION
HEAD REST INSERT
HANDLE POSITIONS
2
To Install Head Rest Insert, thread the Head Rest Straps through the
Harness Strap Adjustment Slots on the seat back.
Attach Head Rest hook and loop straps together.
1 2
1
To provide head support for smaller infants the Head Rest Insert may be used.
The Head Rest Insert can be used with or without the Newborn Positioner.
NEVER use Head Rest Insert with harness in upper slots. Head Rest Insert
could interfere with harness adjustment.
To Adjust the Handle, press both of the Handle Release Buttons and rotate the
handle. There are 3 positions:
Carrying Position Rocking Position
Stationary Position
ALWAYS place handle in one of the LOCKED positions when using Child Restraint in
vehicle.
BE SURE
handle is locked in the “carry position” before lifting carrier by
handle. An unlocked handle could move unexpectedly, causing injury to child.
ADDITIONAL INFORMATION
78
79
ADDITIONAL INFORMATION
HEAD REST INSERT
HANDLE POSITIONS
2
To Install Head Rest Insert, thread the Head Rest Straps through the
Harness Strap Adjustment Slots on the seat back.
Attach Head Rest hook and loop straps together.
1 2
1
To provide head support for smaller infants the Head Rest Insert may be used.
The Head Rest Insert can be used with or without the Newborn Positioner.
NEVER use Head Rest Insert with harness in upper slots. Head Rest Insert
could interfere with harness adjustment.
To Adjust the Handle, press both of the Handle Release Buttons and rotate the
handle. There are 3 positions:
Carrying Position Rocking Position
Stationary Position
ALWAYS place handle in one of the LOCKED positions when using Child Restraint in
vehicle.
BE SURE
handle is locked in the “carry position” before lifting carrier by
handle. An unlocked handle could move unexpectedly, causing injury to child.
ADDITIONAL INFORMATION
80
81
ADDITIONAL INFORMATION
REMOVING CANOPY:
Pull back the fabric and press the button
on Canopy Mount and pull up to remove.
Repeat for the other side.
ATTACHING CANOPY:
Re-attach both of the Canopy Mounts into
the slots on the side of the Carrier.
CANOPY INSTALLATION ON AN AIRCRAFT
When traveling by airplane with your child, Chicco recommends taking the
Carrier on the airplane with you so that you can use it with your child. Not only
will it protect your child during take-off, landing, and turbulence, but also allow
your child to be more comfortable.
• This Child Restraint is certified for use on aircraft. Contact the
airline prior to travel to discuss their Child Restraint policy.
• Use this Child Restraint only on FORWARD-FACING aircraft seats.
• Install Carrier on an aircraft the same way it is installed in a
vehicle when using a vehicle lap belt. Reference Without Base
Installation Lap Belt ONLY on page 56.
1
2
1
ADJUSTING CANOPY:
The Canopy can be adjusted by rotating the canopy forwards or backwards.
ADDITIONAL INFORMATION
80
81
ADDITIONAL INFORMATION
REMOVING CANOPY:
Pull back the fabric and press the button
on Canopy Mount and pull up to remove.
Repeat for the other side.
ATTACHING CANOPY:
Re-attach both of the Canopy Mounts into
the slots on the side of the Carrier.
CANOPY INSTALLATION ON AN AIRCRAFT
When traveling by airplane with your child, Chicco recommends taking the
Carrier on the airplane with you so that you can use it with your child. Not only
will it protect your child during take-off, landing, and turbulence, but also allow
your child to be more comfortable.
• This Child Restraint is certified for use on aircraft. Contact the
airline prior to travel to discuss their Child Restraint policy.
• Use this Child Restraint only on FORWARD-FACING aircraft seats.
• Install Carrier on an aircraft the same way it is installed in a
vehicle when using a vehicle lap belt. Reference Without Base
Installation Lap Belt ONLY on page 56.
1
2
1
ADJUSTING CANOPY:
The Canopy can be adjusted by rotating the canopy forwards or backwards.
ADDITIONAL INFORMATION
82
83
ADDITIONAL INFORMATION
• Cleaning Harness:
Sponge clean using warm water and mild soap. Air dry. Do NOT machine wash.
• Cleaning LATCH Straps:
LATCH Straps cannot be replaced. Sponge clean using warm
water and mild soap. Air dry.
• Cleaning Buckle and LATCH Hardware:
Sponge clean, using warm water only. If debris in buckle,
remove and rinse in warm cup of water. Air dry.
DO NOT USE BLEACH, solvents or household cleaners as they may
weaken plastics and straps.
DO NOT USE SOAPS OR LUBRICANTS on Buckle or LATCH hardware.
It may cause them to malfunction.
• Fabrics may be spot-cleaned, hand or machine washed:
Hand wash using mild soap and water, or machine washed in cold water on
delicate cycle using mild detergent. Hang to dry.
• Cleaning Shoulder Pads:
Hand wash using mild soap and water. Hang to dry.
• Cleaning Plastics:
Sponge clean using warm water and mild soap. Towel dry.
Do NOT remove LATCH or Harness Adjuster Straps. For additional information
visit the Chicco website at www.chiccousa.com or call 1-877-424-4226.
CLEANING AND MAINTENANCE CLEANING AND MAINTENANCE
For softgood removal instructions visit the Chicco website at www.chiccousa.com
or call 1-877-424-4226.
DO NOT USE Child Restraint if any part of the harness is damaged. For
proper removal and installation of the harness straps visit the Chicco website at
www.chiccousa.com or call 1-877-424-4226.
NEVER use Child Restraint without the seat pad.
ADDITIONAL INFORMATION
82
83
ADDITIONAL INFORMATION
• Cleaning Harness:
Sponge clean using warm water and mild soap. Air dry. Do NOT machine wash.
• Cleaning LATCH Straps:
LATCH Straps cannot be replaced. Sponge clean using warm
water and mild soap. Air dry.
• Cleaning Buckle and LATCH Hardware:
Sponge clean, using warm water only. If debris in buckle,
remove and rinse in warm cup of water. Air dry.
DO NOT USE BLEACH, solvents or household cleaners as they may
weaken plastics and straps.
DO NOT USE SOAPS OR LUBRICANTS on Buckle or LATCH hardware.
It may cause them to malfunction.
• Fabrics may be spot-cleaned, hand or machine washed:
Hand wash using mild soap and water, or machine washed in cold water on
delicate cycle using mild detergent. Hang to dry.
• Cleaning Shoulder Pads:
Hand wash using mild soap and water. Hang to dry.
• Cleaning Plastics:
Sponge clean using warm water and mild soap. Towel dry.
Do NOT remove LATCH or Harness Adjuster Straps. For additional information
visit the Chicco website at www.chiccousa.com or call 1-877-424-4226.
CLEANING AND MAINTENANCE CLEANING AND MAINTENANCE
For softgood removal instructions visit the Chicco website at www.chiccousa.com
or call 1-877-424-4226.
DO NOT USE Child Restraint if any part of the harness is damaged. For
proper removal and installation of the harness straps visit the Chicco website at
www.chiccousa.com or call 1-877-424-4226.
NEVER use Child Restraint without the seat pad.
PMS 2747 and PMS 186
