1
2
3
1
2
4
2
2
1
5
1
2
1
6
7
8
9
>75 % recycled paper
>75 % papier recyclé
English
Important safety information
Read this important information carefully before you use the appliance and
its accessories and save it for future reference. The accessories supplied
may vary for different products.
Danger
- Never vacuum up water or any other liquid. Never vacuum up flammable
substances and do not vacuum up ashes until they are cold.
- Never immerse the appliance or the adapter in water or any other liquid,
nor rinse it under the tap.
Warning
- Check if the voltage indicated on the adapter corresponds to the local
mains voltage before you connect the appliance.
- Always check the appliance before you use it. Do not use the appliance
or the adapter if it is damaged. Always replace a damaged part with one
of the original type.
- The adapter contains a transformer. Do not cut off the adapter to
replace it with another plug, as this causes a hazardous situation.
- This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety.
- Children should be supervised to ensure that they do not play with the
appliance.
- Keep the appliance and its cord out of the reach of children.
- The plug must be removed from the socket-outlet before cleaning or
maintaining the appliance.
- Unplug the adapter if you are not going to use the appliance for some
time.
- Do not let the motorized brush move over the mains cords of other
appliances or other cables as this may cause a hazard.
- Keep loose clothing, hair and body parts away from the motorized
brushes.
- Do not cover or block the ventilation openings when the appliance is
operating.
- To prevent damage, do not use the appliance if the filter is not present in
the dust container.
- Do not block the appliance inlet when operating.
- This appliance contains a rechargeable battery that can only be replaced
by a skilled person. Do not open the appliance to replace the
rechargeable battery.
- The rechargeable battery may only be replaced by qualified service
engineers. Take the appliance to an authorized Philips service center to
have the battery replaced when you can no longer recharge it or when it
runs out of power quickly.
- Do not store the appliance at a temperature above 40°C or below 5°C.
- Do not use the appliance in a room with a temperature above 40°C.
- Do not incinerate, disassemble or expose the appliance to temperatures
above 60°C. The rechargeable battery may explode if overheated.
- This vacuum cleaner is designed for household use only. Do not use this
vacuum cleaner to vacuum up building waste, cement dust, ashes, fine
sand, lime and similar substances. Never use the vacuum cleaner without
any of the filters. This could damage the motor and shorten the life of
the vacuum cleaner. Always clean all parts of the vacuum cleaner as
shown in the user manual. Do not clean any parts with water and/or
cleaning agents if this is not specifically shown in the user manual.
Caution
- Only charge the appliance with the adapter supplied. Only use 25V
adapter ZD12D250050 or 29V adapter ZD12D290050.
- During charging, the adapter becomes warm to the touch. This is normal.
- Do not plug in, unplug or operate the appliance with wet hands.
- Do not remove the adapter from the wall socket by pulling at the cord
(Fig. 1). Always unplug the appliance by first detaching the magnetic
connector from the magnetic charging disk (Fig. 2).
- Always switch off the appliance after use and before you charge it.
- Never block the exhaust air openings during vacuuming.
- Do not clean the dust container or the dust container lid in the
dishwasher. They are not dishwasher-proof.
- Do not clean the filter with scouring pads or abrasive cleaning agents.
- Always use the vacuum cleaner with the filter unit assembled.
- If you clean the filter with water, make sure that it is completely dry
before you put it back into the filter holder and dust container. Do not
dry the filter in direct sunlight, on the radiator or in the tumble dryer. Do
not clean the filter holder with water. This part is not washable.
- Replace the filter if it can no longer be cleaned properly or if it is
damaged (see 'Ordering accessories').
- Make sure that the temperature in the room where the appliance is
stored or charged is between 5°C and 40°C.
- Make sure that the appliance is installed with the wall fixture mounted to
the wall according to the instructions in the user manual.
- Be careful when you drill holes in the wall to attach the wall fixture, to
avoid the risk of electric shock.
© 2019 Koninklijke Philips N.V.
All rights reserved
3000.029.6545.2 (29/3/2019)
- If you use the appliance to vacuum fine sand, lime, cement dust and
similar substances, the pores of the filter will become blocked. Clean the
filter regularly.
Electromagnetic fields (EMF)
This Philips appliance complies with all applicable standards and
regulations regarding exposure to electromagnetic fields.
Ordering accessories
To buy accessories or spare parts, visit www.philips.com/parts-and-
accessories or go to your Philips dealer. You can also contact the Philips
Consumer Care Center in your country (see the international warranty
leaflet for contact details).
Warranty and support
If you need information or support, please visit www.philips.com/support
or read the international warranty leaflet.
Recycling
- Do not throw away the product with the normal household waste at the
end of its life, but hand it in at an official collection point for recycling. By
doing this, you help to preserve the environment.
- This product contains a built-in rechargeable battery which shall not be
disposed of with normal household waste. Please take your product to
an official collection point or a Philips service center to have a
professional remove the rechargeable battery.
- Follow your country’s rules for the separate collection of electrical and
electronic products and rechargeable batteries. Correct disposal helps
prevent negative consequences for the environment and human health.
Removing the rechargeable battery
Only remove the rechargeable battery when you discard the product.
Before you remove the battery, make sure that the product is
disconnected from the wall socket and that the battery is completely
empty.
Take any necessary safety precautions when you handle tools to
open the product and when you dispose of the rechargeable battery.
1 Remove the dust container from the appliance.
2 Pull the display cover from the top of the handgrip (Fig. 3).
3 Undo the screw of the handle cover and pull the handle cover off the
appliance (Fig. 4).
4 Undo the bottom cover screw (1) and then remove the side panels. (Fig.
5)
5 Remove the bottom cover screws on the left and right side (1). Then
remove the bottom cover (2) (Fig. 6).
6 Disconnect the battery connector and the display connector from the
printed circuit board (Fig. 7).
7 Undo the battery frame screws (Fig. 8).
8 Remove the battery from the appliance and dispose of it according to
the rules (Fig. 9).
Troubleshooting
This chapter summarizes the most common problems you could encounter
with the appliance. If you are unable to solve the problem with the
information below, visit www.philips.com/support for a list of frequently
asked questions or contact the Consumer Care Center in your country.
Problem Possible cause Solution
The appliance does
not work when I
push the button.
When the battery is
empty,the bottom
segment of the
display flashes red.
To charge the battery,
connect the appliance to the
charging base or attach the
handheld vacuum cleaner
directly to the magnet on the
charging base.
You have to push the
slider forward to
switch on the
appliance.
Push the slider forward to
setting 1 to switch on.
Increase the suction power
further by pushing the slider
to setting 2 to clean dirty
surfaces.
The appliance has
a lower suction
power than usual.
The filter and the
cyclone are dirty.
Clean the filter and the
cyclone. Make sure that you
wash the sponge filter at
least once a month if you use
the appliance regularly.
You have not
attached the dust
container lid properly
to the dust container.
You have not
attached the dust
container to the
appliance properly.
In both cases, there
will be a loss of
suction power.
Make sure that you attach
the dust container lid to the
dust container and the dust
container to the appliance
properly.
An object may be
stuck inside the tube.
Remove the tube and check
for blockages.
Dust escapes from
the appliance.
The filter is dirty. Clean the filter.
The filter is not
present in the
appliance.
Make sure that the filter is in
the appliance and assembled
correctly.
Something blocks
the cyclone.
Check the cyclone for objects
stuck in it and remove any
object that blocks the
cyclone.
If dust falls out of the
dust container, the
dust container lid is
probably not
attached properly to
the dust container.
Empty the dust container and
attach the dust container lid
correctly.
The appliance does
not move smoothly
across the floor
when cleaning a
carpet.
You selected a too
high suction power.
Reduce the suction power by
choosing setting 1.
The brush does not
turn anymore.
The brush
encounters too much
resistance.
Clean the brush with a pair of
scissors or by hand.
The brush may stop
turning when it
encounters too much
resistance from high-
pile carpet.
Switch off the appliance and
then switch it back on again.
You have not
installed the roller
brush in the nozzle
properly after
cleaning.
Follow the instructions in the
cleaning chapter of the user
manual to slide the roller
brush into the nozzle
properly and secure it inside
the nozzle by snapping home
the locking lever.
FC6727, FC6726,
FC6725, FC6723:
The LEDs in the
nozzle do not
come on.
You have not
attached the nozzle
to the appliance or
handheld properly.
Attach the nozzle to the
appliance or handheld
properly.
The appliance is
not charging.
The magnetic
connector is not not
connected correctly
to the charging disk
or the adapter is not
inserted into the wall
socket properly.
Make sure that the magnetic
connector is connected
properly to the charging disk
and that the adapter is
inserted into the wall socket
properly.
You have not
connected the
correct adapter and
cord.
Make sure that you use the
correct adapter and cord.
If you have checked the
above and the appliance still
does not charge, take it to a
Philips service center or
contact the Consumer Care
Center via
www.philips.com/support.
FC6727, FC6726:
The mini turbo
brush does not
function properly.
The roller brush is
blocked.
Remove hairs from the brush
with a pair of scissors (see
user manual).
The roller brush is
blocked by fabric or
surfaces during
cleaning.
Keep the mini turbo brush
aligned with the surface and
do not push the turbo brush
into soft surfaces.
The mini turbo brush
is not fully closed.
Make sure that the top and
bottom parts of the mini
turbo brush are properly
connected and there is no
gap between the two parts.
Check if the locking ring is in
closed position (see user
manual).
When I use my
vacuum cleaner I
sometimes feel
static electricity
shocks.
Your vacuum cleaner
builds up static
electricity. The lower
the air humidity, the
more static electricity
the appliance builds
up.
Discharge the appliance by
frequently holding the tube
against other metal objects in
the room (for example the
legs of a table or chair, etc.).
You can also raise the air
humidity level in the room.
You vacuumed up
fine sand, lime or a
similar substance.
This also causes
static electricity.
Empty the dust container and
clean the filter according to
the instructions in the user
manual.
Problem Possible cause Solution
The bottom
segment of the
display flashes red.
The battery is empty. To charge the battery,
connect the appliance to the
charging base or attach the
handheld vacuum cleaner
directly to the magnet on the
charging base.
All segments of the
display flash
quickly.
An error has
occurred.
First try to recharge the
appliance, empty the dust
container and clean the filter.
If this does not help, take the
appliance to a Philips service
center or contact the
Consumer Care Center via
www.philips.com/support.
简体中文
重要安全信息
使用本产品及其附件之前，请仔细阅读本重要信息，并妥
善保管以供日后参考。 随附的附件可能因产品而异。
危险
- 切勿吸入水或其他任何液体。 切勿吸入易燃物质，也不
要吸入未冷却的灰烬。
- 切勿将本产品或适配器浸入水或其他任何液体中，也不
要将它们放在水龙头下冲洗。
警告
- 在将本产品连接电源前，务必检查当地的电压是否与电
源适配器所标电压一致。
- 使用前，请务必检查产品。 如果产品或适配器受损，请
停止使用。 请务必用原装型号更换损坏的部件。
- 适配器中包含一个变压器。 请勿剪下适配器更换其他插
头，否则将导致严重后果。
- 产品不建议由有肢体、感官或精神能力缺陷或缺少使用
经验和知识的人（包括儿童）使用，除非有负责他们安
全的人对他们进行与产品使用有关的监督或指导。
- 请照看好儿童，本产品不能用于玩耍。
- 将产品及其线缆放在儿童接触不到的地方。
- 清洁或维护产品之前，必须先从插座拔掉插头。
- 如果在一段时期内不使用本产品，请拔下适配器插头。
- 切勿让电动刷在其它产品的电源线或其它线缆上移动，
否则可能会引发危险。
- 确保宽松的衣服、毛发和身体部位远离电动刷。
- 产品运行时，切勿覆盖或堵塞通风口。
- 为防止受损，请在集尘桶中放置过滤网后再使用本产
品。
- 运行时，切勿堵塞产品的进风口。
- 本产品包含充电电池，只能由技术人员更换。 切勿拆开
本产品更换充电电池。
- 只有具备资格的服务工程师才能更换充电电池。 当充电
电池无法继续充电或耗电很快时，请将产品送往授权的
飞利浦服务中心，以更换电池。
- 切勿将产品存放在温度超过 40°C 或低于 5°C 的环境
中。
- 切勿在温度超过 40°C 的房间中使用产品。
- 切勿焚烧、拆卸产品或者将其暴露在温度超过 60°C 的
环境中。 如果过热，充电电池可能会爆炸。
- 根据设计，本吸尘器仅限于家用。 切勿使用本吸尘器清
理建筑垃圾、水泥灰、灰尘、细沙、石灰和类似的物
质。 切勿在没有任何滤网的情况下使用本吸尘器。 这会
损坏马达并缩短吸尘器的使用寿命。 务必按照用户手册
中的说明清洁吸尘器的所有部件。 请勿使用水和/或清洁
剂清洁任何部件（如果用户手册中未特别说明）。
警告
- 只能用随附的适配器为本产品充电。请仅使用 25V 适配
器 ZD12D250050 或 29V 适配器 ZD12D290050。
- 充电期间，适配器会有微热。 这是正常现象。
- 切勿用湿手插入、拔下或操作产品。
- 切勿以拉拔电源线 (图 1)的方式将适配器从电源插座上
拔下。 拔下产品时，务必先将磁性连接器从磁性充电圆
盘 (图 2)上取下。
- 使用后和充电前，请务必关闭产品。
- 吸尘时切勿阻塞排气口。
- 切勿在洗碗机中清洗集尘桶或集尘桶盖。 这些部件不可
在洗碗机中清洗。
- 请勿使用丝绒型洗刷用具或腐蚀性清洁剂清洁过滤网。
- 使用吸尘器时，请确保装上过滤部件。
- 如果用水清洁过滤网，确保其完全干燥后再放回过滤网
架和集尘盒中。 切勿在直射的阳光下、散热器上或滚筒
式烘干机中干燥过滤网。 切勿用水清洁过滤网架。 该部
件不可水洗。
- 如果无法再洗净过滤网或其已损坏 (请参见 '订购配件
')，请予以更换。
- 请确保产品存放或进行充电的房间温度在 5°C 和
40°C 之间。
- 请确保按照用户手册中的说明，用壁装装置将产品安装
到墙上。
- 请注意，在墙上钻孔安装壁装装置时，请避免触电风
险。
- 如果在使用吸尘器清洁细沙、石灰、水泥灰和类似物
质，滤网孔会被堵塞。 定期清洁过滤网。
电磁场 (EMF)
本 Philips 产品符合所有有关暴露于电磁场的适用标准和法
规。
订购配件
如需购买附件或备件，请访问 www.philips.com/parts-and-
accessories 或联系您的飞利浦经销商。 您还可以联系所
在国家/地区的飞利浦客户服务中心（请参阅国际保修卡了
解详细联系信息）。
保修和支持
如需信息或支持，请访问 www.philips.com/support 或阅读
国际保修卡。
回收
- 弃置本产品时，请不要将其与一般生活垃圾放在一起，
应将其交给政府指定的回收中心。 这样做将有利于环
保。
- 此产品包含内置充电电池；请勿将充电电池与一般生活
垃圾一起弃置。 请您将产品送到官方收集中心或飞利浦
服务中心，请专业人士移除充电电池。
- 遵循您的国家/地区有关分类回收电子电气产品和充电电
池的规定。 正确弃置产品有助于避免对环境和人类健康
造成不良后果。
мȞġĈҴˀΙĀǩ؆Ӎߒʔ
ˌɫǩ؆
ĈҴˀΙ
(Pb)
᰽
(Hg)
⬡
(Cd)
ԣᲱ
(Cr (VI) )
Ġ⅑ԓ᧠
(PBB)
Ġ⅑ȕ᧠⓭
(PBDE)
֦ǗКۃଠ،
O O O O O O
Ǘ۷ҒԜ،
O O O O O O
ǕȪϜ֪֙ SJ/T 11364 Āܪǭৠ뺯
OȪФ˽ĈҴˀΙć˽ˌɫǨĈߴΙࠒնġĀߒʔߴć GB/T 26572 ܪǭĀՄʔđŘĪ뺯
XȪФ˽ĈҴˀΙψɺć˽ˌɫĀԚĂߴΙࠒնġĀߒʔɸŜ GB/T 26572 ܪǭĀՄʔđ뺯
拆下充电电池
必须在丢弃本产品前拆下充电电池。 卸下电池之前，请确
保本产品与电源断开连接并且电池电量已耗尽。
当您使用工具打开本产品时以及在您弃置充电电池时，请
采取必要的安全保护措施。
1 从产品上卸下集尘盒。
2 拆下手柄 (图 3)顶部的显示屏盖。
3 拧下手柄盖的螺钉，然后将手柄盖从产品 (图 4)上取
下。
4 拧下底盖螺钉 (1)，然后卸下两侧面板。 (图 5)
5 卸下左侧和右侧的底盖螺钉 (1)。 然后卸下底盖 (2) (图
6)。
6 从印刷电路板 (图 7)上断开电池连接器和显示屏连接
器。
7 拧下电池架螺钉 (图 8)。
8 从产品中取出电池并按照规定 (图 9)处理电池。
故障处理方法
本章归纳了使用本产品时最常见的一些问题。 如果您无法
根据以下信息解决问题，请访问 www.philips.com/support
查阅常见问题列表，或联系您所在国家/地区的客户服务中
心。
问题 可能的原因 解决方法
按下按钮时，
产品不工作。
电池电量耗尽
时，显示屏底段
呈红色闪烁。
为电池充电时，请将产
品连接到充电座，或将
手持式吸尘器直接连接
到充电座的磁体上。
必须向前推动滑
块才能打开产
品。
将滑块向前推动到设置
1 以打开。 将滑块向
前推动到设置 2 以进
一步增加吸力来清洁脏
污表面。
本产品的吸力
比往常要小。
过滤网和旋风滤
网不干净。
清洁过滤网和旋风滤网
。 如果您经常使用本
产品，请确保每月至少
清洗一次海绵滤网。
您未将集尘盒盖
正确安装到集尘
盒上。 您未将
集尘盒正确安装
到产品上。 在
这两种情况下，
吸力将降低。
请确保您将集尘盒盖正
确安装到了集尘盒上，
并将集尘盒正确安装到
了产品上。
管内可能卡有物
体。
取下管件并检查阻塞情
况。
灰尘从产品中
溢出。
过滤网变脏。 清洁过滤网。
滤网未放入产品
中。
确保滤网已放入产品并
正确安装。
污垢堵塞了旋风
滤网。
检查旋风滤网是否被物
体卡住，并清除任何堵
塞旋风滤网的物体。
如果灰尘从集尘
盒中掉出，则集
尘盒盖可能未正
确安装到集尘盒
上。
倒空集尘盒，并正确安
装集尘盒盖。
清洁地毯时，
产品无法在地
板上顺畅移
动。
您选择的吸力太
大。
通过选择设置 1 来降
低吸力。
滚刷不再旋
转。
滚刷遇到的阻力
太大。
用剪刀或用手清洁滚
刷。
滚刷在长毛绒地
毯上遇到太大阻
力时，可能会停
止转动。
关闭产品，然后将其重
新打开。
您没有在清洗滚
刷后将其正确安
装到吸嘴上。
请按照本用户手册“清
洁”一章中的说明，将
滚刷正确滑入吸嘴，并
将锁定杆扣合到位，以
便将滚刷固定到吸嘴
内。
FC6727、
FC6726、
FC6725、
FC6723： 吸
嘴中的 LED 指
示灯不亮。
您未将吸嘴正确
安装到产品上，
或未正确手持。
将吸嘴正确安装到产品
上，或采用正确的手持
方式。
产品未充电。 磁性连接器未正
确连接到充电圆
盘，或适配器未
正确插入电源插
座。
请确保磁性连接器正确
连接到充电圆盘，且适
配器正确插入电源插
座。
您没有连接正确
的适配器和电源
线。
请确保使用正确的适配
器和电源线。
如果已执行上述检查但
产品依然无法充电，请
将其送至飞利浦维修中
心，或通过
www.philips.
com/support 联系客户
服务中心。
FC6727、
FC6726： 迷
你涡轮刷无法
正常工作。
滚刷被阻塞。 用剪刀清除刷子上的毛
发（请参见用户手
册）。
清洁过程中，滚
刷被织物或表面
阻塞。
保持迷你涡轮刷与表面
对齐，且请勿将涡轮刷
推入软质表面。
迷你涡轮刷未完
全关闭。
确保迷你涡轮刷的顶部
和底部正确连接，两部
分之间没有间隙。 检
查闭锁环是否处于关闭
位置（请参见用户手
册）。
有时，在使用
吸尘器时会有
触静电的感
觉。
吸尘器会积聚静
电。 空气湿度
越低，产品积聚
的静电就越多。
经常握住硬管使其与房
间中的其它金属物体接
触（例如，桌椅脚
等），对产品进行放
电。 您也可以增加房
间的空气湿度。
您使用本产品清
理细沙、石灰或
类似的物质。
这还会引发静
电。
请清空集尘盒，并按照
用户手册中的说明清洁
滤网。
显示屏底段呈
红色闪烁。
电池已耗尽。 为电池充电时，请将产
品连接到充电座，或将
手持式吸尘器直接连接
到充电座的磁体上。
显示屏所有指
示段快速闪
烁。
发生错误。 首先尝试为产品充电，
倒空集尘桶并清洁过滤
网。 如果这不起作
用，可以将产品送至飞
利浦维修中心，或通过
www.philips.
com/support 联系客户
服务中心。
న֩ಝ૩ځಉ*%
*%*%
Ԗ*%ѷᤨ
֩ᴮᮮѱ฿ஷፗᄱሺա࠭ٛ
ڿԵᴮ)&
ᮜ߳ၶԀᴮ9ᵲ9
ᮜ߳ᮓᴮ+]
ᮜ߳ၶสᴮ$
ၪஹణᴮឣᜬ֩ࣸ
ڔᴮˊځරᔍᔍࢪ
ᮮѱ฿ᴜˊځᴝఙᬀАԶ
ʰๅࢽ᭕ߪӐ༚ᅶᡬԵ$
Ўځᮂߺజҟཊጦ
న֩ಝ૩ځಉ*%
*%*%Ԗ
*%ѷᤨ
֩ᴮᮮѱ฿ஷፗᄱሺա࠭ٛ
ڿԵᴮ)&
ᮜ߳ၶԀᴮ9ᵲ9
ᮜ߳ᮓᴮ+]
ᮜ߳ၶสᴮ$
ၪஹణᴮឣᜬ֩ࣸ
ڔᴮˊځරᔍᔍࢪ
ᮮѱ฿ᴜˊځᴝఙᬀАԶ
ʰๅࢽ᭕ߪӐ༚ᅶᡬԵ$
Ўځᮂߺజҟཊጦ
న֩ಝ૩ځಉ*%
*%*%Ԗ
*%ѷᤨ
֩ᴮᮮѱ฿ஷፗᄱሺա࠭ٛ
ڿԵᴮ)&
ᮜ߳ၶԀᴮ9ᵲ9
ᮜ߳ᮓᴮ+]
ᮜ߳ၶสᴮ$
ၪஹణᴮឣᜬ֩ࣸ
ڔᴮˊځරᔍᔍࢪ
ᮮѱ฿ᴜˊځᴝఙᬀАԶ
ʰๅࢽ᭕ߪӐ༚ᅶᡬԵ$
Ўځᮂߺజҟཊጦ
న֩ಝ૩ځಉ*%
*%*%Ԗ
*%ѷᤨ
֩ᴮᮮѱ฿ஷፗᄱሺա࠭ٛ
ڿԵᴮ)&
ᮜ߳ၶԀᴮ9ᵲ9
ᮜ߳ᮓᴮ+]
ᮜ߳ၶสᴮ$
ၪஹణᴮឣᜬ֩ࣸ
ڔᴮˊځරᔍᔍࢪ
ᮮѱ฿ᴜˊځᴝఙᬀАԶ
ʰๅࢽ᭕ߪӐ༚ᅶᡬԵ$
Ўځᮂߺజҟཊጦ
న֩ಝ૩ځಉ*%
*%*%Ԗ
*%ѷᤨ
֩ᴮᮮѱ฿ஷፗᄱሺա࠭ٛ
ڿԵᴮ)&
ᮜ߳ၶԀᴮ9ᵲ9
ᮜ߳ᮓᴮ+]
ᮜ߳ၶสᴮ$
ၪஹణᴮឣᜬ֩ࣸ
ڔᴮˊځරᔍᔍࢪ
ᮮѱ฿ᴜˊځᴝఙᬀАԶ
ʰๅࢽ᭕ߪӐ༚ᅶᡬԵ$
Ўځᮂߺజҟཊጦ
న֩ಝ૩ځಉ*%
*%*%Ԗ
*%ѷᤨ
֩ᴮᮮѱ฿ஷፗᄱሺա࠭ٛ
ڿԵᴮ)&
ᮜ߳ၶԀᴮ9ᵲ9
ᮜ߳ᮓᴮ+]
ᮜ߳ၶสᴮ$
ၪஹణᴮឣᜬ֩ࣸ
ڔᴮˊځරᔍᔍࢪ
ᮮѱ฿ᴜˊځᴝఙᬀАԶ
ʰๅࢽ᭕ߪӐ༚ᅶᡬԵ$
Ўځᮂߺజҟཊጦ
న֩ಝ૩ځಉ*%
*%*%Ԗ
*%ѷᤨ
֩ᴮᮮѱ฿ஷፗᄱሺա࠭ٛ
ڿԵᴮ)&
ᮜ߳ၶԀᴮ9ᵲ9
ᮜ߳ᮓᴮ+]
ᮜ߳ၶสᴮ$
ၪஹణᴮឣᜬ֩ࣸ
ڔᴮˊځරᔍᔍࢪ
ᮮѱ฿ᴜˊځᴝఙᬀАԶ
ʰๅࢽ᭕ߪӐ༚ᅶᡬԵ$
Ўځᮂߺజҟཊጦ
న֩ಝ૩ځಉ*%
*%*%Ԗ
*%ѷᤨ
֩ᴮᮮѱ฿ஷፗᄱሺա࠭ٛ
ڿԵᴮ)&
ᮜ߳ၶԀᴮ9ᵲ9
ᮜ߳ᮓᴮ+]
ᮜ߳ၶสᴮ$
ၪஹణᴮឣᜬ֩ࣸ
ڔᴮˊځරᔍᔍࢪ
ᮮѱ฿ᴜˊځᴝఙᬀАԶ
ʰๅࢽ᭕ߪӐ༚ᅶᡬԵ$
Ўځᮂߺజҟཊጦ
保留备用
发行日期: 29/3/2019
