Loading ...
Loading ...
Loading ...
LED display Charging status
LED 1, LED 2 are lit, LED
3 flashes
50%-75%
LED 1, LED 2, LED 3 are
lit, LED 4 flashes
75%-100%
LED 1, LED 2, LED 3,
LED 4 are lit
Fully charged
To start the product (LC 247i)
1. Open the battery lid.
2. Put a charged battery in 1 of the battery holders. For
longer operation time, put a second charged battery
in the other battery holder.
3. Turn the safety key to 1. (Fig. 31)
4. Stay behind the product.
5. Loosen the start inhibitor. (Fig. 18)
6. Push the motor brake handle in the direction of the
handlebar. (Fig. 32)
To start the product (LC347iVX,
LC353iVX)
1. Open the battery lid.
2. Put a charged battery in 1 of the battery holders. For
longer operation time, put a second charged battery
in the other battery holder.
3. Turn the safety key to 1. (Fig. 33)
4. Stay behind the product.
5. Push the ON/OFF button (A) on the control panel.
The display comes on. The battery indicator (B)
shows the battery charge of the 2 batteries. The
number of the battery that operates is shown
adjacent to the battery indicator. For models
LC347iVX, LC353iVX, the display also shows the
set speed. (Fig. 34)
6. Loosen the start inhibitor. (Fig. 35)
7. Push the motor brake handle in the direction of the
handlebar. (Fig. 36)
To use the drive on the wheels
LC347iVX, LC353iVX
• Pull the drive bail in the direction of the handlebar to
start the drive. (Fig. 37)
• Push + and - on the control panel to set the drive
speed in 4 steps. (Fig. 38)
• Release the drive bail to disengage the drive, for
example when you go near an obstacle.
To use the SavE
™
function (LC 247i)
The product has a battery saving function (SavE
™
) that
gives longer operation time.
• Push the SavE
™
button to position 1 to start the
function. (Fig. 39)
• Push the SavE
™
button to position 0 to stop the
function.
Note: The SavE
™
function stops automatically if the
ground conditions make it necessary to have a higher
output. The SavE
™
function starts automatically again
when the ground conditions let it.
To use the SavE
™
function
(LC347iVX, LC353iVX)
The product has a battery saving function (SavE
™
) that
gives longer operation time.
1. Push the SavE
™
button (A) to start the function. The
SavE
™
symbol (B) on the display comes on.
2. Push the SavE
™
button again to stop the function.
The SavE
™
symbol (B) on the display goes out. (Fig.
40)
Note: The SavE
™
function stops automatically if the
ground conditions make it necessary to have a higher
output. The SavE
™
function starts automatically again
when the ground conditions let it.
High load function
When the product cuts long or wet grass, the motor
automatically increases rpm. The motor goes back to
standard mode when high load is not necessary.
Motor stalling
During operation, the blade and motor can temporarily
stop because of obstacles such as grass blockage
below the cutting cover. If this occurs and you keep the
motor brake handle pushed down, the product restarts
automatically. If the product does not restart in 5-10
seconds, it can be necessary to clean below the cutting
cover. Refer to
To clean the product on page 18
.
WARNING:
If the motor stops, the
product tries to restart automatically for 5-10
seconds. Wait for a minimum of 15 seconds
before you do a check of the cutting cover.
WARNING: Before a check of the
cutting cover, release the motor brake
handle, turn the safety key to 0, remove
the battery and wait for a minimum of
5 seconds. There is a risk of injury if
the obstacle is removed and the product
accidentally starts.
16 1696 - 004 - 14.11.2022
Loading ...
Loading ...
Loading ...