Ancona AN2330SSWHT User Manual

Loading ...

— 10 —

Important Safety Information

GAS CONNECTIONS

Important: Do not apply pressure directly to the appliance

manifold pipe when tightening supply connections. The

manifold pipe should be held securely at the pressure

regulator to prevent twisting. Hold the pressure regulator

with a wrench during the tightening of the connection, or

the manifold pipe may be twisted and split and cause a

dangerous leak.

Note: Check all piping connections in the unit for leaks.

Never use an open ame to check for gas leaks. Use some

soap water (50% water and 50% soap) or a leak detector at

all joints and connections to check for leaks in the system.

Do not use a ame to check for gas leaks. It is possible for

connections made at the factory to leak, due to vibration

encountered in transportation. Make certain you have

checked them all, and repair any connections that leak.

• Theapplianceanditsindividualshut-offvalvemustbe

disconnected from the gas supply piping system during

any pressure testing of that system at test pressures in

excess of 1/2 psig.

• Theappliancemustbeisolatedfromthegassupplypiping

system by closing its individual manual shut-off valve

during any pressure testing of the gas supply piping system

at test pressures equal to or less than 1/2 psig (3.5kPa).

GAS LINE SHUT-OFF VALVE

• Toreducethepossibilityofgasleaks,applyTeontape

or a thread compound approved for use with LP or

Natural gases to all threaded connections.

• Installamanualgaslineshut-offvalveinthegasline

in an easily accessed location outside the range in the

gas piping external to the appliance for the purpose of

turning on or shutting off gas to the appliance.

• Installmale1/2’’areunionadapterto1/2”NPTinternal

thread elbow at inlet of regulator. On models equipped

with standard twin burners, install the male pipe thread

end of the ½” are union adapter to the ½” NPT internal

thread at inlet of pressure regulator. Use a wrench on the

regulator tting to avoid damage.

• Install male 1/2” or 3/4” are union adapter to the NPT

internal thread of the manual shut-off valve, taking care

to secure the shut-off valve to keep it from turning.

ELECTRICAL DANGER

Electrical Shock Hazard.

Do not use an extension cord.

Failure to follow these instructions can result in death,

re, or electrical shock.

• Anyadditions,changesorconversionsrequiredinorder

for this appliance to satisfactorily meet the application

needs must be made by a qualied service technician

inaccordancewiththemanufacturer’sinstructions

and all codes and requirements of the authority having

jurisdiction. Failure to follow the instructions could

result in serious injury or property damage. The qualied

agency performing this work assumes responsibility for

the conversion.

• DONOToperatethisapplianceusinga2-prongadapter

or an extension cord. If a 2-prong wall receptacle is the

only available outlet, it is the personal responsibility

of the consumer to have it replaced with a properly

grounded 3-prong wall receptacle installed by a

qualied electrician.

• Severeshock,ordamagetotherangemayoccurifthe

appliance is not installed by a qualied installer or electrician.

• Thisapplianceis240V/60Hz(AN-2330SS/(AN-2336SS),

240V (AN-2348SS). It is recommended to connect to a 15-

Amp or 20-Amp power supply.

• TotalInputPoweris3.2kW(AN-2330SS),3.4kW

(AN-2336SS), 5.2 kW (AN-2348SS), 50 A for ranges. A

dedicated circuit, protected by a minimum 15 to 20-amp

time delay fuse or circuit breaker is required.

• Forpersonalsafety,theappliancemustbeproperly

grounded.

• The power supply must be the correct polarity. Reverse

polarity will result in continuous sparking of the

electrodes, even after ame ignition. If there is any doubt

as to whether the power supply has the correct polarity

or grounded, have it checked by a qualied electrician.

• Your range must be electrically grounded in accordance

with local codes or, in the absence of local codes, in

accordance with the National Electrical Code (ANSI/

NFPA 70, latest edition). In Canada, electrical grounding

must be in accordance with the current CSA C22.1

Canadian Electrical Code Part 1 and/or local codes. A

copy of this standard may be obtained from: National

FireProtectionAssociation,1BatterymarchPark,Quincy,

Massachusetts 02269-9101.

WARNINGS:

• Electrical Grounding Instructions: this indoor gas cooking appliance is equipped with a three-prong (grounding) plug

for your protection against shock hazard and should be plugged directly into a properly grounded three-pronged

receptacle.

• Donotcutorremovethegroundingprongfromtheplug.

• Caution: label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and

dangerous operation. Verify proper operation after servicing.

Loading ...

Ancona AN2330SSWHT 30 Inch White Dual Fuel Freestanding Range

User Manual - Page 10