Loading ...
Loading ...
Loading ...
9
ENGLISH
Motor
Be sure your power supply agrees with the nameplate
marking. Voltage decrease of more than 10% will cause loss
of power and overheating. These tools are factory tested; if
this tool does not operate, check power supply.
Wall Mounting
Some CRAFTSMAN chargers are designed to be wall
mountable or to sit upright on a table or work surface.If wall
mounting, locate the charger within reach of an electrical
outlet, and away from a corner or other obstructions which
may impede air flow. Use the back of the charger as a
template for the location of the mounting screws on the wall.
Mount the charger securely using drywall screws (purchased
separately) at least 1” (25.4mm) long, with a screw head
diameter of 0.28–0.35” (7–9mm), screwed into wood to an
optimal depth leaving approximately 7/32” (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in theslots.
NOTE: Do not attempt to mount CMCB101 charger under a
bench ortable.
NOTE: Only mount CMCB101 charger with the charging
lights pointed upward toward theceiling.
VersaTrack™
WARNING: Do not charge batteries while charger is
hung onTrackwall.
CRAFTSMAN chargers, except the CMCB101, can
be stored on CRAFTSMAN VersaTrack™ Trackwall.
Hooks and accessories are sold separately. Please
refer to the VersaTrack™ Trackwall accessory sheet for
furtherinformation.
NOTE: The CMCB101 charger is not CRAFTSMAN VersaTrack™
Trackwallcompatible.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS
WARNING:
To reduce the risk of serious personal
injury, turn unit off and
remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can causeinjury.
Storage (Fig. A)
Accessory and Air Hose Storage
The accessories
8
,
9
,and
10
are stored on the top of the
unit inside the accessory storage
7
area.
When inflator is not in use, press the high-pressure air
hose
2
into the hose storage area
6
at the base of the tool.
When inflator is not in use, place the accessories into the
storage area located on top of the tool.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can causeinjury.
Charger Cleaning Instructions
WARNING:Shock hazard. Disconnectthe charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non‑metallic brush. Do not use water or
any cleaningsolutions.
Installing and Removing the Battery Pack
(Fig.A, E)
WARNING: Ensure the tool/appliance is in the off
position before inserting the batterypack.
NOTE: For best results, make sure your battery pack is
fullycharged.
1. To install the battery pack
11
into the tool handle, align
the battery pack with the rails inside the tool’s handle
and slide it into the handle until the battery pack is firmly
seated in the tool and ensure that it does notdisengage.
2. To remove the battery pack from the tool, press the
battery pack release button
12
and firmly pull the
battery pack out of the tool handle. Insert it into
the charger as described in the charger section of
thismanual.
Fitting the Accessories (Fig. A, H–J)
Your inflator is supplied with a high-pressure tapered nozzle
adaptor
8
, an inflator needle adaptor
9
, and a Presta valve
adaptor
10
, located on the top of thetool in the accessory
storage
7
area.
1. To use the air chuck
3
, make sure the lever is in the
upposition.
2. Place the air chuck over the stem of the inflator needle
adaptor, high-pressure tapered nozzle adaptor, or the
Presta valve adaptor.
3. Press the lever
13
on the air chuck down to lock it
inplace.
4. Place the inflator needle adaptor, high-pressure tapered
nozzle adaptor, or the Presta valve adaptor into the item
to beinflated.
NOTE: Always make sure that the lever is in the up position
when not in use. When operating your inflator with an
accessory, use only the accessories sold with this unit.
NOTE: Make sure the inflator needle adaptor or other
accessories are firmly locked in place before turning the
inflatoron.
Proper Hand Position (Fig. G)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
suddenreaction.
Proper hand position requires one hand on the handle
5
.
Loading ...
Loading ...
Loading ...