Loading ...
Loading ...
Loading ...
IĈ
1
Ĉ
:O
.$
Â
Ĉ
$
$
$
~
10
Care/cleaning
ʑ
Machine housing, control panel
– Remove detergent residue immediately.
– Wipe with a soft, damp cloth.
– Do not clean the appliance with a water jet.
Clean the detergent drawer ...
... if it contains detergent or fabric softener residue.
1. Pull out, press the insert down, remove the drawer completely.
2. Remove the insert: using your finger, press the insert upwards.
3. Clean detergent dispenser and insert using water and a brush and dry
them.
4. Fit insert and lock it in place (push the cylinder onto guide pin).
5. Insert the detergent drawer.
Leave detergent drawer open so that residual water can evaporate.
ʑ
Drum
Leave washing machine door open so that the drum can dry out.
Rust stains – use chlorine–free cleaning agent, not steel wool.
ʑ
Descaling No laundry in the machine!
Not required if detergent dosed correctly. However, if this does occur, follow the instructions
of the descaling agent manufacturer. Suitable descalers can be purchased on our website
or from customer service. aPage 13
Information on the display panel depending on model
§jDoor can be opened.
ǯDoor cannot be opened due to high temperature inside aWait for the temperature
to drop
The door cannot be opened due to high water level a Drain the water (e.g. select
the Spin/Drain >programme).
§: ³ÅTurn on the tap (cold water) fully;
Supply hose kinked/jammed, water pressure too low. aPage 11:Maintenance,
Filter in the water inlet hose blocked
§: ³µDrain pump blocked aPage 11: Maintenance, Drain pump blocked
Drainage hose/outlet pipe blocked aPage 11: Maintenance, Drainage hose on the
siphon blocked
§: ´Water in the base pan, appliance leaking. Turn off the tap. Call customer service!
'
If the childproof lock is active. Deactivate a Page 5
ª
Flashes if too much detergent is used. a Page 12
Other
displays
Switch off the appliance, wait 5 seconds and switch on again. If the display appears
again, call customer service. aPage 13
– Risk of electric shock. Pull out the mains plug.
– Risk of explosion. No solvents.
11
Risk of scalding.
– Allow detergent solution to cool down.
– Turn off the tap.
Maintenance
Drain pump blocked
Set the programme selector to  Off, pull out the mains plug.
1. Open the service flap.
2. Take the drainage hose out of the holder.
3. Remove sealing cap, allow the detergent solution to flow out. Have a
suitable container ready.
Insert the sealing cap and place the drainage hose back in its holder.
4. Carefully unscrew the pump cover (Caution! residual water).
Clean the interior, the pump cover thread and the pump housing (the fan
impeller in the detergent-solution pump must rotate).
5. Reinsert and screw on the pump cover. Handle should be vertical.
6. Close the service flap.
To prevent unused detergent from flowing into the outlet during the next
wash:
Pour 1 litre of water into dispenser II and start the Spin/Drain
>
programme.
Drainage hose on the siphon blocked
Set the programme selector to  Off, pull out the mains plug.
1. Loosen the hose clip and carefully remove the drainage hose.
(Caution! Residual water.)
2. Clean the drainage hose and siphon spigot.
3. Re-attach drainage hose and secure connection point with hose clip.
Filter in the water inlet hose blocked
Risk of electric shock.
Do not immerse the Aqua-Stop safety device in water (contains electric valve).
Release the water pressure in the supply hose:
1. Turn off the tap.
2. Select any programme (except Spin/Drain >// 2Rinse).
3. Press $Start/Reload button. Leave programme running for
approx. 40 seconds.
4. Set the programme selector to ÂOff. Pull out the mains plug.
Clean the filter:
5. Disconnect the hose from the water tap.
Clean the filter with a small brush.
and/or for standard and Aqua-Secure models:
remove the hose from the rear of the appliance.
Take out the filter with pliers and clean.
6. Connect the hose and check for leaks.
ʑ
ʑ
$
a
ʑ
a
a
a
ʑ
$
ʑ
a
a
ʑ
ʑ
a
ʑ
ʑ
ʑ
0
a
ʑ
.
ʑ
ª
ʑ
a
a
ʑ
ʑ
ʑ
2
Â
a
Â
a
ʑ
a
ʑ
ʑ
ʑ
Loading ...