Loading ...
Loading ...
Loading ...
3. Rinse the shaver cutter and foil frame under
running water or in a sink. Do not use hot water.
Use only warm or cold water (see FIG F-G).
4. After wet cleaning, allow the foil frame and
cutters to air-dry before closing foil frame and
shaver head. Replace shaver head back onto
the main unit until it clicks into place. Wipe the
surface of the main unit with a dry towel.
DEEPLY CLEANING EVERY MONTH:
1. Perform the cleaning steps FIG. A to FIG. E.
2. Remover the inner cutter lock away from the
cutters (see FIG. H).
3. Remove the cutters (see FIG. I).
4. Thoroughly rinse away any debris from inner
and outer cutters (see FIG. J).
5. Replace the inner cutters by matching the
inner cutters to the corresponding outer cutter
hub (see FIG. K).
6. Place inner cutter lock back into position by
sliding it back into the support until it snaps into
place (see FIG. L).
7. Snap shaver head assembly back onto main
unit.
HOW TO CLEAN YOUR
SHAVER HEAD
This is a water-resistant appliance. The appliance
may be cleaned under warm or cold water.
NOTE: When cleaning your unit, make sure the
unit is turned off.
CAUTION!
• To clean the external surfaces of the appliance,
use a damp cloth. Do not use strong detergents
or other chemicals.
• To dry, wipe the surface of the appliance with
a fry towel. Do not use a hair dryer or heater to
dry the appliance.
CLEANING AFTER EVERY USE:
1. To take the shaver head off, twist the top of the
head from “
” to the right and align the arrows to
remove (See FIG. A-C)
2. To take the shaver cover off, twist the top
cover of the head from “
” to the left and align
the arrows to remove (see FIG. D-E).
BEFORE USE:
1. Test one small section of the leg or arm before
using any of the attachments on the rest of the
body.
2. If any sensitivity or allergic reactions occur
discontinue use immediately.
3. Do not use on sensitive or irritated skin.
USING THE ROTARY SHAVER
Never use a foil that is damaged, as this can result
in injury. This appliance is suitable for dry and wet
shaving!
SHAVING
1. Attach the shaver head
2. Twist the battery cover to the right and align
“
” and “ ” marks to start the unit.
3. Hold the shaving foil against the skin, moving
the shaver slowly and smoothly in circular motions
against the grain of your natural hair growth.
4. Don’t push too hard against the skin as this will
cause irritation and may damage the foil.
5. As your skin may be sensitive after shaving, test
your moisturizer on a small patch of skin and wait
to see if irritation occurs.
6. Cleaning: After each use, you will need to clean
the shaver head to ensure continued performance.
7. Twist the battery cover to the left and align
“
” and “ ” marks to turn the unit off.
NOTE: If you are switching to an electric or
battery-operated shaver for the first time, it will
take 12 uses for your skin and hair to adjust to
this new method of removing hair. Do not evaluate
performance until you have allowed your skin and
hair time to adjust.
SAVE THESE
INSTRUCTIONS
WARNING –
1. Women whose skin is sensitive to cosmetics
or easily irritated by shaving, or who suffer from
a skin allergy, should test one section of the leg
or arm before using the shaver head.
2. Do not use this appliance with damaged or
broken foil and blade, as injury may occur.
3. When cleaning, use cold or warm water.
Do not use hot water, sea water, or cleaners,
as they can cause damage to the waterproof
seals.
4. Use in or out of the shower, but do not
leave the entire unit submerged in
water.
5. This appliance is not a toy. Keep away from
children.
TROUBLESHOOTING
There are several things to look for if your unit
fails to operate:
1. Be sure the power handle is turned ON.
2. Make sure that the battery is properly placed
in the battery compartment. Test the battery to be
sure they are working.
3. Check the blades to see if they are clogged
with hair clippings; if so, use the cleaning brush
to remove hair.
4. If the unit still fails to operate, take or send it to
a Conair Service Center (see warranty procedure
and addresses).
OPERATING
INSTRUCTIONS
FOR YOUR ALL-IN-ONE
FACIAL TRIM SYSTEM
FOR HOUSEHOLD
USE ONLY
OPERATING INSTRUCTIONS
BATTERY INSTALLATION:
1. Twist bottom housing of unit to the left and
align triangles “
” and
“
” and pull (see FIG. 1).
2. Insert 1 AA battery (not
included).
3. Slide bottom housing
back in place and align
“
” and “ ”.
4. Ensure the battery
is installed correctly
with regard to polarity (+
and -).
5. Remove the battery if it is no longer functional
or if the trimmer is left unused for an extended
period of time.
6. Clean the battery contacts and also those of
the device prior to battery installation.
7. Remove used battery promptly.
8. Always purchase the correct size and grade
of battery most suitable for its intended use.
GETTING STARTED
TO SWITCH TRIMMER HEADS
1. Make sure the unit is turned off.
2. Turn head to the right, aligning triangles
“
” and “ ” (see FIG. 2).
3. Switch the attachment head and put new head
on then turn to the left and align “
” with “ ”
(see FIG. 3).
INSTRUCTIONS FOR USE
1. Twist the battery cover to the left to unlock
battery cover.
2. Insert 1 AA battery according to the polarity
marking, return the battery cover, turn to the right
and align with “
” and “ ” marks to lock, and
then twist to right again, the unit will start to work
and align “
” and “ ” marks.
3. After use, turn off the power making the
“ ” of the battery cover align with “ ” mark
(see FIG 1).
FIG. 1
FIG. 2 FIG. 3
lt85_18pg050897_ib_comp.indd 1 1/18/18 12:42 PM
Loading ...
Loading ...