Loading ...
Loading ...
Loading ...
8
Read and understand all
assembly instructions before attempting
assembly and setup. Failure to comply may
cause serious injury.
5.0 Setup and assembly
5.1 Shipping contents
1 Belt Grinder with mounted abrasive
1 Operating instructions and parts manual
1 Product registration card
5.2 Unpacking and installing
The Grinder does not require assembly, only
mounting to a support, such as bench or table.
Inspect contents for shipping damage. Report
damage, if any, to your distributor. Do not discard
shipping materials until grinder is installed and
running properly.
Lift grinder out of carton along with plywood
platform. Remove platform and place grinder on a
sturdy table or workbench. Secure to workbench
with fasteners through the four holes in base. See
sect. 4.1 for hole spacings.
An optional adaptor plate (not included) is available
for mounting the grinder to the JET JDCS-505 Dust
Collection Stand. See your dealer or visit our
website for ordering information.
IMPORTANT: The abrasive belt has been de-
tensioned for shipping. Belt must be properly
tensioned before operating grinder. See sect. 7.3.
5.3 Dust collection
It is recommended that a dust collection system be
used with this machine. Connect dust hose (not
provided) to the 2-inch port at back of grinder and
secure with clamp.
6.0 Electrical connections
Electrical connections must be
made by a qualified electrician in compliance
with all relevant codes. This machine must be
properly grounded to help prevent electrical
shock and possible fatal injury.
Before connecting to power source, be sure switch
is in off position.
It is recommended that the Belt Grinder be
connected to a dedicated 20 amp circuit with circuit
breaker or time-delay fuse marked “D”. Local
codes take precedence over recommendations.
6.1 GROUNDING INSTRUCTIONS
1. All Grounded, Cord-connected Tools:
In the event of a malfunction or breakdown,
grounding provides a path of least resistance for
electric current to reduce the risk of electric shock.
This tool is equipped with an electric cord having an
equipment-grounding conductor and a grounding
plug. The plug must be plugged into a matching
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Do not modify the plug provided - if it will not fit the
outlet, have the proper outlet installed by a qualified
electrician.
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. The
conductor with insulation having an outer surface
that is green with or without yellow stripes is the
equipment-grounding conductor. If repair or
replacement of the electric cord or plug is
necessary, do not connect the equipment-grounding
conductor to a live terminal.
Check with a qualified
electrician or service personnel if the grounding
instructions are not completely understood, or if
in doubt as to whether the tool is properly
grounded. Failure to comply may cause serious
or fatal injury.
Use only 3-wire extension cords that have 3-prong
grounding plugs and 3-pole receptacles that accept
the tool's plug.
Repair or replace damaged or worn cord
immediately.
2. Grounded, cord-connected tools intended for use
on a supply circuit having a nominal rating less than
150 volts:
This tool is intended for use on a circuit that has an
outlet that looks like the one illustrated in A, Figure
6-1. An adapter, shown in B and C, may be used to
connect this plug to a 2-pole receptacle as shown in
B if a properly grounded outlet is not available. The
temporary adapter should be used only until a
properly grounded outlet can be installed by a
qualified electrician. This adapter is not permitted in
Canada. The green-colored rigid ear, lug, and the
like, extending from the adapter must be connected
to a permanent ground such as a properly grounded
outlet box.
3. Grounded, cord-connected tools intended for use
on a supply circuit having a nominal rating between
150 - 250 volts, inclusive:
This tool is intended for use on a circuit that has an
outlet that looks like the one illustrated in D, Figure
6-1. The tool has a grounding plug that looks like the
plug illustrated in D. Make sure the tool is connected
to an outlet having the same configuration as the
plug. No adapter is available or should be used with
this tool.
Loading ...
Loading ...
Loading ...