Loading ...
Loading ...
Loading ...
LocatetheL.Rgasorificespudsinliterature
package.Orificespudsarestampedwithanumber___
andmarkedwithtwocolordotsandagroove. /'_:_
_r5/16 '' (7 ram)
nut driver groove L.P.gas
orifice spud
orifice spud
Replace orifice _-_
spud with the ./_
number listed ,('( _ _.
inchart " rifice
nor / number
embly
L.P.Gas
Surface Propane Orifice Color
burner Rate(BTU/hr) Number Marking
Left rear 8,000 L80 Green/Lt. Blue
Left front 11,000 L99 Green/Yellow
Right front 8,000 L80 Green/Lt. Blue
Right rear 5,000 L65 Green/Brown
A brass orifice spud is located in the center of each burner
throat about 2" (5 cm) below the cooktop. Apply masking
tape to the end of a 5/16" (7 ram) nut driver to fit snugly
over the orifice spud. Press driver down onto the spud of
the left front burner and remove by turning spud counter-
clockwise and lifting it out. Replace the Natural gas spud
with the appropriate L.R gas spud shown in the table.
Continue to replace the remaining orifice spuds, one at a
time. Place the Natural gas spuds in plastic parts bag for
future use and keep with literature package. Replace burner
caps using both screws and burner grates.
pin hood f/t_'_/
L.P.gas
Natural gas _illli_" decrease
!ncrease gas _ gas
increase _t" _:_ _ decrease
flame size _ flame size
pre-set at factory _ orifice
for Natural gas hood
,. Oven burner: Use 1/2" (13 ram) combination
wrench to turn the orifice hood clown snug onto pin
(approximately 2 to 2-1/2 turns). DO NOT OVERTIGHTEN.The
burner flame cannot be properly adjusted if this conversion
is not made.
,. Broil burner: Use 1/2"(13 mm) combination wrench to
turn the orifice hood down snug onto pin (approximately 2
to 2-1/2 turns). DO NOT OVERTIGHTEN.The burner flame
cannot be properly adjusted if this conversion is not made.
Page 14
,. Reinstall the storage drawer. Complete installation
sections D through E, Pages 9-13. Checking for proper
cooktop burner and oven flame is very important.
YOU MUST ADJUST "LOW" SETTING FOR EACH COOKTOP
BURNER. SEE STEP 16, PAGE 10.
The small inner cone should have a very distinct blue flame
1/4" (6 ram) to 1/2" (13 mm) long.The outer cone is not as
distinct as the inner cone. L.R gas flames may have a
slightly yellow tip. If the flame is noisy or blowing, it is
getting too much air. If the flame is soft and lazy, it is not
getting enough air.
Natural gas conversion
,. Complete installation sections A-C (Pages 7-8) before
converting cooktop to natural gas. Check that main gas
supply line has been shut off and the power supply cord is
disconnected.
preaaure_ _ ......
regulator /_
_pressure _
.I _ /-_, \
plastic cover plastic cover
_- cap
--washer --
Nat. gas L.P, gas
L.P.
DO NOT REMOVETHE PRESSURE REGULATOR.
,. Pressureregulator: Remove storage drawer and locate
pressure regulator at back of range. Remove plastic cover.
Turn cap marked "LP:' on front of pressure regulator
counterclockwise with a wrench to remove. Do Not disturb
or remove the spring beneath the cap.Turn the cap over and
reinstall cap on regulator so that the letter "N" is
visible. Replace plastic cover over cap.
Loading ...
Loading ...
Loading ...