Loading ...
Loading ...
Loading ...
13
ENGLISH
Making Cuts with a Cut-Off Machine
CAUTION: Before attempting to start, grasp tool firmly
with both hands beforelifting.
WARNING: Cut‑off saw not intended for surface
grinding or other applications where side loading of
the blade isencountered.
WARNING: Edge cutting can be performed only with
wheels that are designed and specified for this purpose.
Protect yourself during edge cutting by directing the
open side of the guard away from you, theoperator.
WARNING: Wheels used for cutting may break or kick
back if they bend or twist while the tool is being used to
do cut‑offwork.
WARNING: Always be alert for gyroscopic forces that
can be generated by a rapidly spinning cutting wheel.
Moving the cut‑off machine sideways can create a
gyroscopic force, causing the operator to experience an
unexpected perpendicular change indirection.
Wet Cut Method (Fig.A, J, K)
CAUTION: Close battery door and securely latch it
closed before using anywater.
Reducing the Risk of Kickback (Fig. I)
WARNING: Reactive forces may occur at any time
the cutting wheel is inmotion.
WARNING: To reduce the risk of kickback, avoid
cutting with the upper quadrant of the cutting
wheel whenever possible. Be extremely mindful of
binding or pinching of the cutting wheel in this area as
it can cause severe reactive forces resulting inkickback.
• Always be alert to any potential movement that could
cause the material being cut to close and pinch the
cuttingwheel.
• Proper support of the material will ensure the cut stays
open during the cut. If you cannot properly support the
material, do not use a cut‑off machine to make yourcut.
• Always support exposed pipe in the ground so that it
is stable and is able to support weight. Use additional
support closer to the area to be cut to prevent the pipe
from sagging and pinching the cuttingwheel.
• Material that is under stress could shift when it is cut.
Uneven pipe beds could exertstress.
• Always make sure the section of material being removed
is also supported. After the first cut is made you may
have to move supports or add additional support to
ensure both sides of the material are evenlysupported.
• Be aware of weakened work areas that could shift or slide
causing your supports tomove.
Heavy Load Indicator LED (Fig. A)
The heavy load indicator LED
7
will illuminate as a warning
when the tool is being pushed too hard. Continuing to use
the tool after the LED is lit could cause the tool to shut down
or reduce runtime.
Proper Hand Position (Fig. H)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position asshown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
suddenreaction.
WARNING: Never use the cut‑off machine with one hand.
Always grip the cut‑off machine firmly with bothhands.
WARNING: Make sure the handles and grips of
your cut‑off machine are secure and free of grease
and/ormoisture.
Proper hand position for both left‑ and right‑handed users
requires your right hand on the rear handle
1
and your left
hand on the front handle
8
.
Installing and Removing the Battery Pack
(Fig. G)
NOTE: For best results, make sure your battery pack is
fullycharged. Use only DEWALT FLEXVOLT™ batteries with
this cut‑offmachine.
Unlock battery door
5
by moving battery door latch
4
towards the front of the tool and open as shown in Figure G.
To install the battery pack
19
into the tool, align the
battery pack with the rails inside the tool and slide it in
until the battery pack is firmly seated. Ensure that it does
notdisengage.
Close the battery door
5
, and push the battery door latch
4
toward the back of the tool to lock the batterydoor.
To remove the battery pack from the tool, unlatch and open
the battery door. Then press the battery release button
20
and firmly pull the battery pack out of the tool. Insert it into
the charger as described in Charging aBattery.
Do not leave the battery dooropen.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can causeinjury.
the DEWALT Tool Connect™ app. For proper installation of
the DEWALT Tool Tag, refer to the DEWALT Tool Tagmanual.
To learn more,visit:
www.DEWALT.com/en‑us/jobsite‑solutions/tool‑connect
Wireless Tool Control (Fig. A)
CAUTION: Read all saftey warnings, instruction and
specifications of the appliance which is paired with
thetool.
Your tool is equipped with a Wireless Tool Control
transmitter which allows your tool to be wirelessly paired
with another Wireless Tool Control device, such as a DEWALT
dustextractor.
To pair your tool using Wireless Tool Control, depress the
trigger switch
2
and the Wireless Tool Control pairing
button on the seperate device. An LED on the seperate
device will let you know when your tool has been
successfullypaired.
Loading ...
Loading ...
Loading ...