Loading ...
Loading ...
Loading ...
4
again. If this abnormal situation happens several times, please
contact the customer service.
Danger of burns!!
- The use of an extension lead is not recommended, as
overheating of the extension lead may occur during the
operation of the heater.
The appliance complies with the following EC directives:
- Low Voltage Directive 2006/95/EC and subsequent
amendments;
- EEC Directive 2004/108 on electromagnetic compatibility
(EMC) and subsequent amendments;
INTRODUCTION
Thank you for choosing a De’Longhi product. Please take a few
moments to read the instructions to avoid risks or damage to the
appliance.
Symbols used in these instructions
Important warnings are identied by the symbols below.
It is important to respect the warnings.
Failure to respect the warnings could lead to electric shock, serious
injury, burns, re or damage to the appliance.
Important!
Failure to observe the warning could result in injury or damage to
the appliance.
Danger of burns!!
Failure to observe the warning could result in burns or scalds.
Please note:
This symbol indicates recommendations and important information
for the user.
General instructions
Remove the heater from the packaging. Check that neither the
heater nor the power cable has been damaged during transport.
Do not operate the heater if damaged. Remove all publicity
material present on the appliance. The appliance is suitable for
free-standing or wall-mounted usage. Do not assemble the feet if
wall-mounted.
Electrical connection
- Before connecting the appliance to the current outlet, check
that the voltage indicated on the appliance rating plate is the
same as your electric plant and that it can stand the power
consumption (Watt) indicated by the labelling.
- If more than one appliance is used at once, it is important to
ensure that the electric plant is able to support the power
required.
Mounting the feet
Turn the appliance upside down on a rug or soft surface in order to
prevent damaging the paint nish.
Fix the feet to the appliance with the nr. 4 screws B supplied
(see g. 1), 2 screws for each foot.
Wall-Mounting Installation
The wall mounting kit contains:
4 metal brackets (A)
2 screws 4,8x13 PH (B)
4 screws 4,5x25 PH (C)
4 plastic anchors 6x30 (D)
Required tools for assembly and estimated assembly time
Screwdriver PH 2 x 100 (Phillips type)
Estimated assembly time: 30 minutes
Before installing the unit , make sure of the following:
a. The appliance must not be located directly beneath a
current outlet.
b. The plug and outlet must be easy to reach after
installation.
c. No electric cables or other pipes could be damaged
during the installation.
d. Keep away from curtains or ammable materials.
To wall-mount, proceed as follows:
Turn the appliance upside down on a at stable surface . Using a
screwdriver, x the 2 brackets A with the 2 screws B as shown in Fig.
2. For brick walls use a 6 mm concrete drill bit.
For plaster board or false (hollow) walls, it is recommended to use
appropriate screws and anchors (not supplied).
1. Before drilling the wall, mark the exact points, respecting the
minimum distances as shown in g. 3.
2. Drill the wall where previously marked, and insert the plastic
anchors D.
3. Fix the 2 metal brackets A using the two screws C provided.
4. Hang the appliance on the bracket.
5. Mark out the 2 lower xing points. Remove the appliance, drill
the lower holes and insert the wall anchors D.
6. Now, you can hang back the heater on the bracket and x the
lower part of the appliance with the 2 remaining screws C.
USE
Operation and use
Plug into the mains, turn the thermostat dial to maximum (position
6) and turn the appliance on by means of the power selector (see
description) as described below:
• Turn the power selector knob to the Min position to select
minimum power.
• Turn the power selector knob to the Med position to select
medium power (only in some models).
Loading ...